Lumens VC-TR40N Auto Tracking Camera

Important To download the latest version of Quick Start Guide, multilingual user manual, software, or driver, etc., please visit Lumens https://www.MyLumens.com/support

Package Contents

Product Appearance

I/O functions Introduction

Description of LED indicator

Instruction for installation

Instruction for installation of TR40 and TR40,AT

• Note: The VC-TR40 comes in a standard version and an AT version. The AT version requires different firmware for upgrades, which can be downloaded from the Lumens website.
• The AT version differs only in the tracking function; all other functions are the same.

Introduction

• The TR40 and TR40, AT have different Tracking functions. You can decide which version will suit your needs.
• a. VC-TR40: To track or frame the target in the tracking zone.
• Available modes: Everywhere Tracking, Stage Tracking, Partition Tracking, Auto Framing, Partition Framing
• b. VC-TR40, AT: Offers a choice between Presenter and Audience modes.
• Presenter Mode: The camera tracks the target within the tracking zone.
• Audience Mode: The camera starts tracking when it detects the target standing up.
• Refer to the  5.2.4 Tracking page for more information

Scenario for TR40 and TR40, AT

• a. Applicable distance range of VC-TR40/TR40,AT : 2 -14 m.
• Best tracking target distance recommended: 8 m
• The default maximum tracking distance is 12m, but it can changed to 14m via the webpage.
• Refer to 5.2.12 System Settings – Control
• b. Mounting height: 2 – 3 m, best height recommended: 2.4 m
• <Note> To maintain the best tracking results, please avoid having images of people on posters, screens, monitors or TVs in the background

Scenario for VC-TR40,AT

• VC-TR40, AT*1: Install at the back of a room to capture the presenter.
• VC-TR40, AT*2: Install at the front of a room to capture the audience.

Preparation before installation

• Installation and connection of HD cameras require special skills. To install by yourself, please follow the necessary steps, ensure steady and tight installation of the device, and pay attention to your safety to avoid any accidents.
• Ensure the safety of the installation environment. Please do not install the device on an unstable ceiling or in a place where the device is in danger of falling to avoid any accident.
• Please check whether the accessories in the box are complete or not. Please contact the supplier for any shortage, and make sure to keep the accessories in the box intact.
• Please choose a proper place for the installation of the camera in advance. Please determine an installation place according to the following requirements
• a. Confirm the position for the object to be captured.
• b. Confirm whether the camera is set at a proper distance from other light sources.

Instruction for installation

I would like to install the camera on the desk

• Please install the machine on a flat desk
• Do not grab the camera head by hand when handling the device
• Do not rotate the camera head by hand. Improper rotation may result in the breakdown of the camera

I would like to install the camera on the ceiling/wall/TV stand

• Lumens can provide the following optional accessories. Please contact your Lumens distributer if needed for purchase
• VC-WM14 3 in-1 Folding Bracket
• VC-WM15 Ceiling Mounted Bracket
• For installation of brackets, please download the VC-WM14/VC-WM15 Quick Installation Guide from the Lumens website
• Install on the TV
• Install on the ceiling
• Install on the wall
• Note: The camera will only track the target within the panoramic scene. Please ensure that the panoramic view covers the entire area you want to shoot.

Camera Size

• Length x Width x Height: 190 x 138 x 185 mm
• Weight: 1.3 Kg

Dimensions of the bottom of the machine

• The camera can be mounted on a 1/4”-20 UNC PTZ tripod deck by using the lock holes on the bottom of the tripod

Connecting devices

<Remark> Network cable port, supporting PoE (IEEE802.3af) power supply

RS-232 connection (up to 7 Lumens cameras)

RS-232 pins definition instructions

Remote Control and Setting Menu

Remote Control

Setting Menu

<Remark> Press [MENU] on the remote control to enter the setting menu; the bold underlined values in the following table are defaults.

Network Function Settings Description

Connecting Camera to Network

Connecting to Internet

Two common connection methods are shown below

1. Connecting via switch or router
2. To connect directly through the network cable, the IP address of the computer should be changed so that it is on the same network segment as the camera E.g.:
   • The factory-preset default IP address of the camera is 192.168.100.100. The computer IP address must be set with the same network segment, such as 192.168.100.101 so that the computer can be connected correctly to the camera
   • Change network settings

Using the Browser to View the Images

• Open the browser, and enter the IP address of the camera in the address bar E.g.: http://192.168.100.100 (default IP address)
• Enter the administrator’s account and password

<Remark> For the first-time login, please refer to5.2.10System Settings – User to change the default password

Using RTSP Player to View the Images

• Free software can be used for RTSP connection, such as VLC, Quick Time, and PotPlayer

RTSP connection address formats are as follows:

• RTSP Stream 1 => rtsp://camera IP:8557/h264
• RTSP Stream 2 => rtsp://camera IP:8556/h264
• RTSP Stream3 => rtsp://camera IP:8553/h264
• Stream 3 is for the Panoramic image.

If password authentication is enabled, the RTSP connection address is as follows:

• rtsp://Username: Password@VC IP address: port/h264
• To enable the  password authentication function, please refer to5.2.8 System Setting – Network
• Example: Open the VLC software, click [Open Network Streaming], and enter the URL: rtsp://192.168.100.150:8557/h264.

Web Page Menu Function Description

Login Screen

No	Item	Function Descriptions
1	User Login Account	Enter user login account (default: admin)
2	User Password	Enter user password (default: 9999) <Remark> For the first-time login, please refer to 5.2.10 System  Settings – User to change the default password
3	Remember the user account and password	Save the user login account and password to the browser. When you log in next time, there is no need to re-enter them
4	Language	Supporting English/Traditional Chinese/Simplified Chinese
5	Login	Log into the administrator screen on the website

Live Video – PTZ Control

No	Item	Function Descriptions
1	Camera ID/location	Display camera ID/location Please refer to 5.2.7 System Settings – Output Setting
2	Preview window	Display the screen currently captured by the camera

Live Video – Camera Setting

No	Item	Function Descriptions
1	Exposure	Mode: Select exposure mode (Full Auto/Shutter Pri/Iris Pri/Manual/ White Board) Gain Level: Adjust the gain level (adjustable only under the “Manual”) Gain Limit: Adjust the gain limit (adjustable only under the “Manual”) Exposure Comp. Level: Select exposure compensation level WDR: Set the level of wide dynamic range (WDR) to obtain better images Iris Level: Adjust the size of the aperture (adjustable only under the “Manual” or “Aperture Priority” Shutter Speed: Adjust the shutter speed (adjustable only under the “Manual” or “Shutter Priority” Anti-Flicker: Enable Anti-flicker function(adjustable 50Hz or 60Hz)
2	White Balance	Mode: Select the color temperature mode Open Push WB: Single color temperature execution adjustment (adjustable only under the “One Push WB” Manual Red/Blue: Manually adjust blue/red color temperature

3	Focus	AF Sensitivity: Set automatic focus sensitivity AF Frame: Set automatic focus range
4	Mirror	Mirror: Set image mirroring Flip: Set image flip
5	Pan Tilt Zoom(PTZ)	Pan/Tilt limit: Enable, and set the pan/tilt limit Preset Speed: Set the rotation speed of the cradle head when the Preset is executed Initial Position: Set the camera lens to return to Last MEM or 1st Preset after POWER ON <Remark> 1st Preset = Preset 0 D-Zoom Limit: Set the D-Zoom Limit PTZ Speed Comp: After it is activated, the Pan/Tilt moving speed will vary from the zoom position Initial Position: Set the camera lens to return to the last operated position or the first preset position after POWER ON Motionless Preset: When the function is enabled, the screen will Freeze when the Preset is executed. Freeze will be released after the Preset is completed
6.	Photo	2D noise reduction: 2D noise reduction settings 3D noise reduction: 3D noise reduction settings Image Mode: The user may customize his/her desired image mode Hue: Hue adjustment of the image; Adjustable when the image mode is set to Custom

Tracking

(This Tracking section is for the VC-TR40. For the TR40, AT version, please refer to section 5.2.4.A)

13	Tracking Mode	Set the Tracking Mode (Everywhere Tracking/Stage Tracking/Center Stage/Partition Tracking/Auto-Framing/Partition Framing)
14	Sensitivity	Set tracking sensitivity
15	Tracking Speed	Set tracking speed
16	Target Lost Time	Set a delay for taking action after a tracking object is lost
17	Target Lost Action	Set the action after a tracking object is lost
18	Auto-trigger zone	When people walk into the trigger zone you have set, the auto-tracking will be turned on.
19	Tracking Mode Setting	VC-TR40 supports 6 kinds of tracking mode
19.1	Settings – Everywhere tracking	Body Size: Set Full/Half Body Head Position: Set the head position of the person on the screen Block Area: Click into the Edit mode, frame by holding the left mouse button, and set the block area Tracking Zone: Set a specific tracking range.
19.2	Settings – Stage Tracking	Body Size: Set Full/Half Body Head Position: Set the head position of the person on the screen Block Area: Click into the Edit mode, frame by holding the left mouse button, and set the block area Stage Zone: Click into the Edit mode, frame by holding the left mouse button, and determine the tracking range
19.3	Settings – Partition Tracking	Set Partition Tracking. Up to 4 zones can be set When a person enters the zone of a partition, the camera switches to the partition. Tracking is not performed in the zone, but everywhere outside the partition Please refer to 5.2.4.2 Partition Tracking for the setting steps

		Body Size: Set Full/Half Body Head Position: Set the head position of the person on the screen Block Area: Click into the Edit mode, frame by holding the left mouse button, and set the block area Partition Edit: Edit, save partition positions, and preview the partition image. Click to enlarge the partition image, and then click the enlarge icon to cancel the preview. Partition amount: Display the total stored number of Partition. Starting Partition: Initiating the partition position
19.4	Setting – Center Stage	Enable Center Stage allows the camera to keep the target in the center of the frame frame-based image in the PTZ lens after calling a new preset. Center Stage: on/off Head Position: Set the head position of the person on the screen
19.5	Settings – Auto -Framing	Body Size: Set Full/Half Body Head Position: Set the head position of the person on the screen Block Area: Click into the Edit mode, frame by holding the left mouse button, and set the block area Framing Size: Tight / Medium / Wide
19.6	Setting – Partition Framing	Partition Edit: Edit, save partition positions, and preview the partition image. Click to enlarge the partition image, and then click the enlarge icon to cancel the preview. Partition amount: Display the total stored number of Partition.

Stage

1. Select [Stage] for Tracking Mode, and click to access the settings
2. Select Zone to enter Edit mode, and click the left mouse button to frame it (yellow frame) in the panoramic preview window, determining the area and moving range. After framing, use the mouse to click the frame line to move or delete it.
3. Select to click the left mouse button to frame it (red frame) in the panoramic preview window, and set the block area
4. After framing, click on the setting
5. Click to enable the Stage feature

Partition

1. Select [Partition] for Tracking Mode, and click to access the settings
2. Click to enable the Partition edit, click the left mouse button to frame it (orange frame) in the panoramic preview window, determine the area, and click to save. The partition icon below will be changed to the saved position
3. If you need to set other partitions, please continue framing, and then click to save
   • <Remark> Overlapping partition positions may cause abnormal tracking behavior
4. Click to enable the Partition feature

Tracking (For VC-TR40,AT version)

No	Item	Function Description
1	Camera ID/ location	Display the camera ID and location. Refer to 5.2.7 System-Output
2	Preview window	Display the image from the Lens.
3	Panoramic preview window	Display the image from the Panoramic Lens. Left-clicking the target with the green icon on head by the mouse to track the desired target in the panoramic scene
4	Mode	Presenter: Track the target on the stage. Audience: Track the audience when an audience does the corresponding movement.
5	Auto Tracking	On / Off	Auto Tracking
6	Zoom ratio	Zoom In/Out
7	Pan/Tilt setting	Pan / Tilt the camera to your desired angle. When the auto-tracking is enabled, the PTZ is uncontrollable
8	Take Turn	Change the tracking target from left to right in order one at a time after clicking the button. Not supported in Audience mode.
9	Setting Area	To display the Stage zone and Blocking zone you have drawn in a panoramic field.
10	Basic setting-Presenter	Designated ID: The targets detected in the panoramic scene will display a green indicator for easier identification. Sensitivity: Low/Middle/High. Target lost time: Set how long the camera will take to act after losing the target Target lost Action: what action will be done after losing the target: Back to start position/Stay in the last position/PTZ back to the center and wide

		Tracking speed: Low/Middle/High Outside Stage: Whether the camera will keep tracking after leaving the Stage area. Body Size: Full/Upper Head position: Set the individual’s head will be in which position in the scene. Low/ Middle/ High Area Setting Profiles and Synchronized: Save or Load the zone profile you have drawn. Stage Zone: Click it then start editing. Use the left button of the mouse to draw a tracking zone in the panoramic scene. The camera will then track the target in this area. Blocking Zone: Click it then start editing. Use the left button of the mouse to draw a blocking zone in the panoramic scene. The camera will then not track the target in this area. Remark: <Please note that the Stage and Blocking zone can overlap if needed.>
10	Basic Setting-Audience	Designated ID: The targets detected in the panoramic scene will display a green indicator for easier identification. While tracking, click on a different indicator to switch to a different target. Sensitivity: Low/Middle/High Stand Up Lost Time: After triggering, how long the camera will keep tracking the target? Target Lost Action: What the camera will do after losing the target? PTZ back to the enter and wide/ Stay in the last position/ Back to start position.

		Area Setting Profiles and Synchronized: Save or Load the zone profile you have drawn. Blocking Zone: Click it then start editing. Use the left button of the mouse to draw a blocking zone in the panoramic scene. The camera will then not track the target in this area.
11	Commands-Press enter (To be used with Lumens LC300)	Noted: To use the camera with the Lumens LC300 intelligent director function, the checkbox above needs to be checked. Send Times: Once/ Always Send Up/Down Stage: Configure that the camera will only track the target when the individual is on stage. Detect Type: Single Object / Mutlple Object. Behavior Detect: Normal: Will not send the PTZ start and Stop command. PTZ     Start-Stop: The PTZ Stop and PTZ Start command will be sent.
11	Command-Audience (To be used with Lumens LC300)	Noted: To use the camera with the Lumens LC300 intelligent director function, the checkbox above needs to be checked. Send Times: Once / Always send
12	Advanced-Audience/Presenter (To be used with Lumens LC300)
		Noted: To use the camera with the Lumens LC300 intelligent director function, the setting here needs to be configured correctly. Connect by: Network/ Serial port Protocol: UDP/ TCP Director IP: Enter the LC300 IP address.

How to use the VC-TR40, AT with the Lumens LC300 Intelligent Director function

No	Item	Function Description
1	Target lost action	Allows you to choose which scene will be displayed when the target is lost
2	Presenter/Audience Settings	Allows you to choose which scene will be displayed and what action will trigger the scene change.
3	Priority	When two events are triggered, you can choose which one should take priority.
4	On/Off	Enable or disable the Intelligent Director.
5	Apply	Apply the settings
Please remember to complete the Command and Advanced sections’ settings to link the VC-TR40, AT, and LC300.

Audio

No	Item	Function Descriptions
1	Audio Enable	Select to enable the Audio function Audio In: Set Line In / Mic In Encode sample rate: Encode type and sample rate (48KHz(AAC) Volume: Adjust Audio Volume
2	Audio Delay	After checking the box, set the audio delay time (10 ~ -500 ms)
3	Apply/Cancel	Apply/Cancel Audio Setting

Streaming

No	Item	Function Descriptions
1	Streaming 1/ Streaming 2	Supporting 2-way streaming output
2	Streaming parameter setting	Please refer to 5.2.6.1 Streaming Parameter Setting for relevant settings
3	RTSP	Select to enable RTSP Enable/Disable Multicast It is suggested to enable Multicast when the number of users online watching the live image simultaneously is more than 4 Enable/Disable Password Authentication RTSP connection format can be found in 5.1.3 Using RTSP Player To view the Images The username/password is the same as the web login password of the camera, please refer to 5.2.10 System Settings – User to add/modify account information
4	RTMP/ RTMPS	Copy the RTMP web address provided by the RTMP service platform and paste it to the RTMP connection address to publish the camera images on the RTMP service platform To upload to YouTube for live streaming, please refer to 5.2.5 Audio to turn on the audio function
5	SRT	Check to enable and set SRT streaming After the SRT streaming is opened, it will be connected automatically upon startup The port number must be set in the range above 1024 with a maximum value of 9999 <Remark> The following port is to be used by the camera. The setting of the said port may not connect correctly 8554, 8555, 8557, 8080, 9090, 1935 The delay time is 20 to 8000 microseconds. The default value is 120 microseconds
6	NDI	For VC-TR40N only. Please refer to 5.2.7 Streaming – NDI.

Streaming parameter setting

Stream – NDI (For VC-TR40N only)

No	Item	Function Descriptions
1	Camera ID/ Location	Displaying ID/location according to [System] > [Output] settings
2	Group Name	The group name can be modified here and set with Access Manager – Receive in NDI Tool If no group is assigned, the machine belongs to the Public. As the default of Access Manager includes Public, Studio Monitor can discover this machine. If a group is assigned, but this group is not added to Access Manager, Studio Monitor cannot discover this machine. If a group is assigned and this group is added to Access Manager, Studio Monitor can discover this machine. <Remark> The name can contain commas (,) to distinguish different groups Example: “default, 123, ABC” means this machine belongs to three groups at the same time (default/ 123/ ABC)
3	NDI|HX	HX2/HX3 can be set on VC-TR40N n   HX2: HX2 is supported n   HX3: HX3 is supported (Stream 1/ 2 will be disabled.)
4	Multicast	Multicast Settings. It is recommended to enable this feature when there are more than 4 viewers online simultaneously
5	Discovery Server	Check to enter the Server IP address
6	Apply	After the setting has been modified, click this button to apply the settings

System – Output Setting

No	Item	Function Descriptions
1	Camera name	Change the camera name here Supporting 1 – 32 characters for the camera name Please mix uppercase and lowercase letters or numbers for characters. Special symbols such as “/” and “space” cannot be used <Remark> Modifying this field will modify the Onvif device name synchronously
2	Camera Location	Modify the location of the camera, such as Room 1 Supporting 1 -32 characters for the camera location Please mix uppercase and lowercase letters or numbers for characters. Special symbols such as “/” and “space” cannot be used <Remark> Modifying this field will modify the Onvif device location synchronously
3	Resolution	Set the resolution of the camera After switching the resolution, the camera will restart. Please refresh the browser
4	HDMI format	Select YUV444/RGB
5	Privacy Mode (UVC)	Enable/Cancel Privacy Mode After the function is enabled when the camera is turned off via the remote control or software, the lens will automatically turn to the bottom right to ensure the user’s privacy
6	Apply/Cancel	Apply/Cancel Setting

System – Network

No	Item	Function Descriptions
1	DHCP	Network setting of the camera. Change of setting is available when the DHCP function is closed
2	HTTP port number	Set HTTP port. The default Port value is 80
3	HTTPS port number	Set HTTPS port. The default Port value is 81
4	Apply/Cancel	Apply/Cancel Setting

System – Date & Time

Function Descriptions

Display the current camera/PC date and time, and set the display format and synchronization way When Manually Set is selected for [Time Settings], Date & Time can be customized

System – User

Function Descriptions
Add/Modify/Delete user account Supporting 4 – 32 characters for username and password Please mix uppercase and lowercase letters or numbers for characters. Special symbols or the underlined cannot be used Authentication Mode: Set the new account management permissions
	User Type	Administrator (Admin)	Operator (Operator)	Viewer (Viewer)
	View images	V	V	V
	Settings	V	V	X
	Account management	V	X	X

System Settings – Control

No	Item	Function Descriptions
1	Protocol	Supporting VISCA protocol
2	Baud Rate	Choose the transmission speed of the control signal as 9600/38400
3	VISCA address	The camera ID addresses 1 ~ 7 can be assigned. Select 0 for automation
4	Tracking LED status	Enable/Disable the LED in the front panel flick when tracking is triggered.
5	Tracking Distance	Change the longest tracking distance to either 12 or 14 meters. (The camera will reboot itself after switching)
6	Apply/Cancel	Apply/Cancel Setting

Maintenance

No	Item	Function Descriptions
1	Firmware Upgrade	Select the firmware file, and click [Upgrade] to update the firmware. <Remark>Update takes about 2-3 minutes. <Remark> Please do not operate or turn off the power of the device during the update to avoid firmware update failure.
2	Factory Reset	Reset all configurations to factory default settings Except for the Network Setting after reset
3	System Settings	Save setup parameters as a Profile, and users can download and upload camera setup parameters
4	Error Log	If the camera operates abnormally, please export the error log and provide it to Lumens for confirmation
5	Reboot	·   Reboot: Conduct the reboot immediately. ·   Daily Reboot Time: Choose the desired exact time for the camera to reboot. <Remark: Can only be configured when SNTP is on.> ·   Reboot Timing: Choose how many hours later the camera will reboot: 1HR~24HR.

About

Function Descriptions

Display the firmware version, serial number, and other related information of the camera For technical support, please scan the QR code at the bottom right.

Troubleshooting

This chapter describes problems you may encounter while using VC-TR40. If you have questions, please refer to related chapters and follow all the suggested solutions. If the problem still occurs, please contact your distributors or the service center.

Safety Instructions

Always follow these safety instructions when setting up and using the VC-TR40 PTZ Video Camera:

1. Operation
   • Please use the product in the recommended operating environment, away from water or sources of heat
   • Do not place the product on a tilted or unstable trolley, stand, or table.
   • Please clean the dust on the power plug prior to usage. Do not insert the product’s power plug into a multiplug to prevent sparks or a fire.
   • Do not block the slots and openings in the case of the product. They provide ventilation and prevent the product from overheating.
   • Do not open or remove covers, otherwise it may expose you to dangerous voltages and other hazards. Refer all servicing to licensed service personnel.
   • Unplug the product from the wall outlet and refer servicing to licensed service personnel when the following situations happen:
   • If the USB port becomes damaged or frayed.
   • If liquid is spilled into the product or the product has been exposed to rain or water.
2. Installation
   • For security considerations, please make sure the standard mount you use is in line with UL or CE safety approbations and installed by technician personnel approved by agents.
3. Storage
   • Do not place the product where the cord can be stepped on as this may result in fraying or damage to the lead or the plug.
   • Unplug this product during thunderstorms or if it is not going to be used for an extended period.
   • Do not place this product or accessories on top of vibrating equipment or heated objects.
4. Cleaning
   • Disconnect all the cables before cleaning and wipe the surface with a dry cloth. Do not use alcohol or volatile solvents for cleaning.
5. Batteries (for products or accessories with batteries)
   • When replacing batteries, please only use similar or the same type of batteries.
   • When disposing of batteries or products, please adhere to the relevant instructions in your country or region for disposing of batteries or products.

Precautions

• This symbol indicates that this equipment may contain dangerous voltage which could cause electric shock. Do not remove the cover (or back). No user-serviceable parts inside. Refer servicing to licensed service personnel.
• This symbol indicates that there are important operating and maintenance instructions in this User Manual with this unit.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

IC Warning

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.

EN55032 CE Warning

• Operation of this equipment in a residential environment could cause radio interference.
• Warning: Operation of this equipment in a residential environment may cause radio interference

Extron IP Link Compatible

• Extron has developed and tested an IP Link driver for this product. Using IP Link technology, this device can be monitored, controlled, and supported over a standard Ethernet network.
• To enable IP Link network connectivity and control, you must install and configure an IP Link-enabled device such as a MediaLink controller or IP Link Ethernet control interface. For more information, please see www.extron.com/iplc”.

Supplier’s Declaration of Conformity

47 CFR § 2.1077 Compliance Information

• Manufacturer: Lumens Digital Optics Inc.
• Product Name: VC-TR40
• Model Number: PTZ Video Camera
• Responsible Party – U.S. Contact Information
• Supplier: Lumens Integration, Inc.
• 4116 Clipper Court, Fremont, CA 94538, United States
• e-mail support@mylumens.com

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation

Copyright Information

Copyrights © Lumens Digital Optics Inc. All rights reserved

• Lumens is a trademark that is currently being registered by Lumens Digital Optics Inc.
• Copying, reproducing, or transmitting this file is not allowed if a license is not provided by Lumens Digital Optics Inc. unless copying this file is for backup after purchasing this product.
• To keep improving the product, the information in this file is subject to change without prior notice.
• To fully explain or describe how this product should be used, this manual may refer to names of other products or companies without any intention of infringement.
• Disclaimer of warranties: Lumens Digital Optics Inc. is neither responsible for any possible technological, editorial errors or omissions, nor responsible for any incidental or related damages arising from providing this file, using, or operating this product.

Documents / Resources

Lumens VC-TR40N Auto Tracking Camera [pdf] User Manual VC-TR40, VC-TR40N, VC-TR40N Auto Tracking Camera, VC-TR40N, Auto Tracking Camera, Tracking Camera

References

• User Manual