• Shure: 2202§ Shure: 2202
• Sennheiser: 45
• Sennheiser TCCM: 443
• Nureva: 8931
• Yamaha: 49280
• Audio-Technica : 17300

Note Only Nureva allows customized PORT

• Sennheiser:-90~0 (recommended -55)
• Nureva:0~120 (recommended 40+)
• Audio-Technica:0~60 (recommended 30)
• Yamaha:0~126 (recommended 80+ for RM-CG / 70+ for RM-W)

• Call Preset Position： Click a number first and the
• Store Preset Position： Click a number first and then Store

• Array No.: Applicable to Shure / Audio-Technica devices
•  Azimuth Angle: Applicable to Sennheiser, Nureva, and Yamaha devices. Angles can be manually adjusted

•  Center Stage： When the camera has been triggered to a preset position, the individual will be centered on the screen for 5 seconds before tracking stops.

• Sound Device
• Camera
• Video Output

• Save/ Load: Save or Load the desired profile.
• AutoSave Interval: Set the auto saving interval.
• System Startup Waiting Time: Set startup waiting time.

After AI-Box1 powers on, it will automatically search for microphones and cameras. If the devices have a long boot-up time, AI-Box1 may not connect to the devices properly. To prevent this issue, please adjust the system waiting time based on the current environment and the boot-up time of the microphones and cameras.

• Cross: 4-split screen
• PBP: Picture by Picture screen
• Crop: Screen cropping function

Choose either Cross/PBP only

1. Connect one end (with two rings) to the computer.
2. Connect the other end (with three rings) to the Reserve hole on the Cam Connect Pro.
3. The end with a single ring should be connected to the speaker to capture the audio.

 Audio Trigger(dB): Set the audio detection threshold (-100~0 dB).The microphone will only trigger detection when the volume exceeds the set threshold.
Detective Time(s): Set the duration of the detection (0~10 seconds)
Enable: On / Off
Apply: Click to apply the settings.

Connection: The Lumens BC200 auxiliary camera must be connected. The BC200 is set to be released in Q1 2025. For a more detailed introduction, please refer to the BC200 user manual at that time. 

Auxiliary Camera: Enable or disable the BC200 camera.
Vision Zone Detection: This feature is not functional at the moment and is not for use.
Apply: Click to apply the settings.

• Array Microphone Number：Select the desired number of microphones to connect
• Devices: Select a Microphone
• Device IP: Enter the IP address of the microphone
• Displays the microphone’s port
  • Shure: 2202
  • Sennheiser: 45
  • Sennheiser TCCM: 443
  • Nureva: 8931
  • Yamaha: 49280
  • Audio-Technica : 17300

Note Only Nureva allows customized PORT

• Connect: Enable/Disable microphone connection
• Advanced Function Settings

• Audio Trigger Level > dB： Triggered when an audio source exceeds the specified dB value.
  • Sennheiser:-90~0 (recommended -55)
  • Nureva:0~120 (recommended 40+)
  • Audio-Technica:0~60 (recommended 30)
  • Yamaha:0~126 (recommended 80+ for RM-CG / 70 up for RM-W)
• Time To Trigger Preset: Audio Reception Delay Settings

When a second sound trigger occurs, there will be a delay in triggering camera preset based on the configured duration in seconds.

• Back To Home Time: If there is no audio input, the camera will move to its home position after the set seconds.
• Back To Home Position:    You can select either the Home position or designate a preset number.

• Voice Tracking: When enabled, the microphone can receives signals, and the camera would moves to preset positions when triggered. When setting preset positions, disable this function.

Mapping Q’ty: Select the number of locations to be mapped. Up-to 128 presets supported.
Note Shure MXA310/ MXA910/ MXA920/ Audio-Technica no supported
Note Not supported with Shure MXA310/ MXA910/ MXA920 and Audio-Technica microphones.

• Indicator: a green light indicates that the microphone is detecting a sound.
• Array No. / Azimuth Angle：
  • Array No.: Applicable to Shure/ Audio-Technica devices
  • Azimuth Angle: Applicable to Sennheiser, Nureva, and Yamaha devices. The angle can be manually adjusted
• Primary Camera: Select a Primary camera from the dropdown menu
• Secondary Camera: Select a desired Secondary camera from the dropdown menu. When a camera is triggered to a preset position, and another preset position for the same camera is subsequently triggered, the Secondary camera will be the prior one to move to instead of the primary camera.

Note: This feature is available only when Seamless Switching is enabled

• Preset No.: Select the preset position for the camera from the dropdown menu
• AI Setting：Enable / Disable AI tracking
  • Center Stage：When the camera has been triggered to move to a preset position, the individual will be centered on the screen for 5 seconds before tracking stops.
  • Continuous Tracking ： The camera will continuously track the individual, maintaining them in the center position.

• Refresh : search the cameras in this network segment.
• Add： Manually type the IP address, then click Add

Note Please ensure that cameras and AI-Box1 are in the same network segment。

• Connect / Disconnect ： Click [Connect] to enable or disable the connection with the camera.
• PTZ Control： Click it to access the camera’s webpage. Default account: admin/ 9999

For more information, please refer to the camera’s user manual.

A.  Camera: Assign commands for connected cameras to move to a preset position or return to their home position.
B.  Microphone:

1. trigger count: Set the number of triggers (1~100) required to activate the camera.
2. All Mic off Stream: Define the action Cam Connect Pro will take when the microphone stops receiving sound. For example, change the image layout scene or send commands to cameras.

(See example below)
C.  Layout:

1. Video Layout: Cross / PBP
2. Video Layout of camera quantity: 1×1 / 1×2 / 1×3 / 2×2
3. Video source to specific position

1. Script Start:
   • This block must be placed at the beginning of any valid script.
   • Set the priority to determine which script takes precedence when multiple scripts are active.
2. Script End: This block must be placed at the end of any valid script
3. Delay time: milliseconds / seconds / minutes
   • Set the custom time and select the units.
   • This block can be used as a stopover point in a script.

Example:

Note: A valid script must always include both the Script Start block and Script End block.
E.  Leave: Exit the page
F.  Save: Save the settings
G.  Run: Start executing the script
H.  Bin: Drag unwanted blocks to the bin icon to discard them.
I.  Execution Log: Displays the activity log of the AI Director. 

Script edition: Customize Mode example

A. Camera

Preset Cruise
Set how the preset positions of 2–3 cameras are triggered in sequence
Mode 1: Assign one preset position for each camera. Each camera moves to its preset position in order.

Configurable value:

1. Movement speed (degrees per second) for the camera when the preset position is triggered.
2. Delay time(seconds)

Camera settings

• Move to a specific preset position or home position
• Movement speed (degrees per second) for the camera when the preset position is triggered.

B. Layout

1. Layout: Cross / PBP
2. Video Layout for Camera Quantity: 1×1 / 1×2 / 1×3 / 2×2
3. Video source to specific position

C. Control

1. Script Start:
   • This block must be placed at the beginning of any valid script.
   • Set the priority to determine which script takes precedence when multiple script are active.
2. Script End: This block must be placed at the end of any valid script.
3. Delay time: milliseconds / seconds / minutes
   • Set the custom time and select the units.
   • This block can be used as a stopover point in a script.
4. Reschduled in _ seconds: Specify how many seconds will be needed before triggering the next step.
5. Repeat Count: How many times the scrpt will repeat
6. Script stop: Stops the script execution.
7. Loop Script: The script will repeat continuously.

Example:
Note: A valid script must always include both the Script Start and Script End blocks.

D.  Leave: Exit the page
E.  Save: Save the settings
F.  Run: Start executing the script
G.  Bin: Drag unwanted blocks to the bin icon to discard them.
H.  Execution Log: Display the activity log of AI Director.

• Cross: 4-split screen
• PBP: Picture by Picture screen
• Crop: Screen cropping function

Note Choose either Cross/PBP only

• Connect one end (with two rings) to the computer.
• Connect the other end (with three rings) to the Reserve hole on the Cam Connect Pro.

• The end with a single ring should be connected to the speaker to capture the audio.

Audio Trigger(dB):
Set the audio detection threshold (-100~0 dB).The microphone will only trigger detection when the volume exceeds the set threshold.
Detective Time(s): Set the duration of the detection (0~10 seconds)
Enable: On / Off
Apply: Click to apply the settings.

1. Check the power supply of camera or PoE power supply is stable.
2. Make sure the cameras are on the same network as the Cam Connect AI-Box1.
3. Replace the cables and make sure they are not faulty

1. Make sure the Azimuth Angle settings in the Cam Connect software include that angle position
2. Check the blocked zones in the Sennheiser Control Cockpit software. Refer to 5 Microphone Settings for details.

1.  Please check if you are using static IP.

Turn to DHCP and try update again.