Lucci decor 261091 Citta Table Lamp Instruction Manual
Lucci decor 261091 Citta Table Lamp

Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before using the product. Please keep the instructions for future reference.

Installation requirements

  • Select a suitable location for the fitting;
    • Ensure it is on a flat and stable surface.
    • This product is suitable for indoor use only.
    • Do not place flammable material near or over the fitting.
    • Ensure the fitting is not installed next to any air vents and is not in any moist or damp areas.
  • Do not exceed the maximum wattage rating.
  • Take care not to pull any electrical wires during unpacking as this may damage the connection.
  • Lay out all the components on a smooth surface and make sure there are no components missing before assembling.
    If parts are missing, return the complete product to the place of purchase for inspection or replacement.
  • Check whether the fitting has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
  • Do not plug into the mains power socket outlet before or during assembly. Only do so after the portable lamp is fully assembled and ready to use for the first time.

Installation directions

  1. Remove all packaging material from the product.
  2. To help with assembly, lay the fitting on its side on a smooth non scratch surface.
  3. Install the body of the lamp onto the base. There is a label with a line at the adjusting joint (figure A), this line represents the middle point of the adjusting joint. Ensure the label is facing the forward direction and is positioned over the base before tightening the nut. The head of the lamp or the label must not face the backwards direction, as this will affect the stability of the portable lamp. (figure B)
    Installation directions
  4. When everything is aligned, tighten the nut using the spanner provided. (figure A)
    Installation directions
  5. To adjust the angle of the shade, no tool is required. It can be adjusted in both the horizontal and vertical directions.
    The maximum horizontal adjustment for the shade is 180°. (figure D)
    Installation directions
    The maximum vertical adjustment for the shade is 60°. (figure E)
    Installation directions

    Do not force or adjust the shade more than these maximum angles. It may damage the fitting and internal wiring.
    NOTE: During normal operation the shade may be hot to touch. Always ensure the power is OFF and the fitting has cooled down before performing any maintenance, cleaning, changing the globe or adjustment to the fitting.
  6. Install a globe (not included) into the lamp holder. (figure C) Do not exceed the maximum rated wattage.
    Installation directions
  7. Insert the plug into the socket outlet and ensure it is fully plugged in.
  8. Turn power on at the mains power socket outlet and use the cord line switch to turn the lamp on/off.

NOTE: Do not force or adjust the shade more than the maximum angles shown above.
Doing so may damage the fitting and the internal wires.

Safety tips

  • Always ensure the power is OFF and the fitting has cooled down before performing any maintenance, cleaning, changing the globe or adjustment to the fitting.
  • To avoid injury or damage to the fitting, ensure that power leads and screws are secure before connecting the power.
  • Young children should be supervised to ensure that they do not play with the portable lamp.
  • Handle the fitting and/or shade with care to avoid any damage or breakage.
  • Select a suitable location away from liquids and hazards.
  • Ensure that the fitting does not come in contact with corrosive chemicals, etc.
  • To clean, wipe with a damp clean cloth. Never soak the fitting with water

Specifications

SKU # 261090 261091
Model # LS-AT240B-BLK LS-AT240B-WH
Rated Voltage 220-240V~ 50Hz
Rated Wattage 45W Max.
Lamp Holder ES / E27
Weight 1.8kg
Dimensions W:375mm    H:605mm MAX

Warranty

  • This fitting is covered by a 12 month warranty. Please retain proof of purchase.
  • Warranty will be void if there is any damage due to improper usage or modification to the fitting.

Citta
SKU# 261090, 261091
Rated Voltage 220-240V~ 50Hz

 

Documents / Resources

Lucci decor 261091 Citta Table Lamp [pdf] Instruction Manual
261090, 261091, 261091 Citta Table Lamp, Citta Table Lamp

Leave a comment

Your email address will not be published.