„Keilton Basic RM51“ nuotolinio valdymo pultas šviestuvų jutikliams

Aprašymas

The RM51 Remote is used to program the configurations of the Keilton Basic sensors using infrared (IR) communications with the devices. It offers 6 default modes of configurations plus manual settings. Customer configurations can be created, saved, and then sent to each device, ensuring a rapid deployment.

Savybės

• Mažas energijos suvartojimas.
• Infrared communication.
• Setting most of the Keilton Sensors G2.
• Custom Configurations can be saved to A, B, C, D, or For.
• 40′ maximum IR range.
• RML (included with new orders, available as an accessory for order), installed, will increase the IR range. (See table below)

Specifikacijos

Užsakymo informacija

Modelis	Aprašymas
RM51.A0	Basic Sensor Controller RM51
RM51.A1	Basic Sensor Controller RM51 With RML

Užsakymo informacija – priedai

Modelis	Aprašymas
RML	Extended IR range for commissioning

Matmenys

Produkto etiketė

Nuotolinės instrukcijos

Atminties režimas (paleidimas)
To begin commissioning, follow these steps:

1. Pasirinkite atminties specialistąfileA, B, C, D arba E.
2. The remote’s indicator lights will flash, indicating the currently saved settings.
3. Settings can be configured by pressing the appropriate buttons in the highlighted gray area of the remote (TRIM-LEVEL, SENSITIVITY, HOLD TIME, STANDBY DIM, STANDBY TIME, and PHOTOCELL). Review the selected settings and make changes as needed.
4. Point the remote at the desired luminaire and press “SEND.”
5. The luminaire will flash twice to confirm that he settings are saved. Changing a parameter in a memory profile will automatically override previous settings.
6. If configuring multiple luminaires, repeat steps 4 and 5 after selecting the configured memory mode.

E Mode allows for visual adjustment to choose the desired dimming level.

Dienos šviesos panaudojimas (F režimas)
Continuous Adjustment Mode adjusts dimming levels based on daylight.

1. Point the remote at the desired luminaire and press “ON,” then press DIM+ or DIM- to adjust the dimming level.
2. Press “F.” The indicator lights on the remote will show the current saved settings. Note: Only TRIM-LEVEL, SENSITIVITY, and HOLD TIME can be selected for Daylight Harvesting settings
3. Review the selected settings and make changes as necessary. Press “SEND.”
4. If the configuration is successful, the luminaire will flash twice to confirm that the setting is saved. If configuring multiple luminaires, select the configured Daylight Harvesting settings, then follow steps 1, 2, and 3.

Papildomos nuotolinio valdymo funkcijos

ON	Posūkiai ON šviestuvai.
IŠJUNGTA	Posūkiai IŠJUNGTA šviestuvai.
TESTAS	The fixture enters the test mode and exits automatically after 5 minutes. The test mode parameters are configured as follows: Trim-level: 100 proc. Jautrumas: AUKŠTAS, Laikymo laikas: 2, Standby dim: 50 proc. Budėjimo laikas: 2s.
RESET	Trim= 100 %, Sensitivity = Aukštas, T1 = 5 min, Standby Dim = 30 %, T2 = 60 min, Photocell = IŠJUNGTA.
DIM+/-	Press Dim+ or Dim- to adjust brightness in 0.5V increments. Hold the button for continuous Pritemdymas
TRIM-LYGIS	Set the Maximum brightness.
JAUTRUMAS	Set the motion sensitivity of the sensor LOW:50 % / AUKŠTAS:100 proc. IŠJUNGTA: disable the motion detection function.
HOLDTIME	Laikotarpis, praeinantis be buvimo aptikimo prieš perjungiant į budėjimo režimą.
BUDĖJIMO REŽIMAS	Select any standby dim level.
LAIKYMAS LAIKAS	Standby time, when the time is set to “∞”, the daylight detection function is activated.
NUOTRAUKOS	visible light threshold, the fixture is allowed to be turned on when it falls below the threshold LOW:5fc / AUKŠTAS:20fc, CAL: Collect the current visible light illuminance as the threshold, IŠJUNGTA: disable PHOTOCELL function.
REŽIMAS	Default configuration parameters for modes A į F.
SIŲSTI	Siųskite nustatymus į jutiklį.
NUMATYTOJI A REŽIMAS	Trim= 100 %, Sensitivity = Žemas, T1 = 30 min, Standby Dim = 50 %, T2 = ∞, Photocell = CAL.
NUMATYTOJI REŽIMAS B	Trim= 100 %, Sensitivity = Žemas, T1 = 30 min, Standby Dim = 50 %, T2 = 15 min, Photocell = CAL.
NUMATYTOJI REŽIMAS C	Trim= 100 %, Sensitivity = Žemas, T1 = 30 min, Standby Dim = 50 %, T2 = 15 min, Photocell = IŠJUNGTA.
NUMATYTOJI REŽIMAS D	Trim= 50 %, Sensitivity = Žemas, T1 = 30 s, Standby Dim = 50 %, T2 = 30 min, Photocell = CAL.
NUMATYTOJI REŽIMAS E	Manual Dimmer Mode, Trim 100 %.
NUMATYTOJI REŽIMAS F	Daylight Harvesting, Trim= 50 %, Sensitivity = Žemas, T1 = 15 min.

Susisiekite su mumis

• 7001 Columbia Gateway Drive, Suite 210, Columbia, MD 21046, USA
• T: +1 443-320-2233 (M-F 9 am-5 pm ET)
• E: support@autani.com

DUK

How do I change the memory profile nustatymus?

Select the desired memory profile on the remote and adjust settings as needed before pressing SEND to save

Can I configure Daylight Harvesting settings for multiple luminaires simultaneously?

No, you need to configure Daylight Harvesting settings for each luminaire individually using the F Mode on the remote.

What is the expected operation if the user sets Standby Time to something other than INFINITE?

moiton -> the intensity of ambient light is lower than the threshold set by the PC->turn on the light and dim to trim-level->t1 timeout->dim to standby dim ->t2 timeout->turn off the light.

If it does not turn OFF the fixture, why would Mode B and D use CAL as the default?

The ambient light intensity stored by CAL will serve as the threshold for turning on the lights, but it has no connection with the function of turning off the lights.

Dokumentai / Ištekliai

„Keilton Basic RM51“ nuotolinio valdymo pultas šviestuvų jutikliams [pdfNaudotojo vadovas RM51.A0, RM51.A1, RM51 nuotolinio valdymo pultas šviestuvo jutikliui, RM51, nuotolinio valdymo pultas šviestuvo jutikliui, šviestuvo jutiklis, šviestuvo jutiklis

Nuorodos

• Vartotojo vadovas