Įvadas
This manual provides essential information for the safe and efficient operation of your VEVOR 3"-550 Deep Well Submersible Pump. Please read these instructions thoroughly before installation and use, and retain them for future reference.
The VEVOR 3"-550 Deep Well Submersible Pump is designed for reliable water supply from deep wells, suitable for domestic, agricultural, and industrial applications. It features a robust stainless steel construction, a powerful 550W motor, and a high flow rate.
Saugos instrukcijos
ĮSPĖJIMAS: Nesilaikant šių saugos nurodymų, gali kilti elektros smūgis, gaisras arba sunkūs sužalojimai.
- Įsitikinkite, kad maitinimo šaltinis atitinka siurblio įtampątage (230 V / 50 Hz).
- Prieš atlikdami bet kokius techninės priežiūros ar montavimo darbus, visada atjunkite maitinimo šaltinį.
- Do not operate the pump without water or at a low water level to prevent overheating and damage.
- The pump must be fully submerged during operation.
- Handle the pump with care. Use the provided rope for lowering and raising the pump.
- Ensure all electrical connections are properly sealed and protected from water.
- Šis prietaisas nėra skirtas naudoti asmenims (įskaitant vaikus), kurių fizinės, jutimo ar psichikos negalios arba neturintys patirties ir žinių, nebent už jų saugumą atsakingas asmuo juos prižiūrėtų arba instruktuotų, kaip naudoti prietaisą.
Produktas baigtasview
The VEVOR 3"-550 Deep Well Submersible Pump is constructed from durable stainless steel, designed for longevity and resistance to corrosion. It features a powerful copper motor with built-in overheat protection.
Image: VEVOR 3-inch Deep Well Submersible Pump, showing its stainless steel body and integrated power cable.
Pagrindinės funkcijos:
- Nerūdijančio plieno konstrukcija: Enhanced durability and corrosion resistance (IP68 waterproof rating).
- Powerful Copper Motor: 550W motor with high-precision rotor and built-in overheat protection.
- Didelis srautas: Maximum flow of 2100 L/h (35 L/min).
- High Head Lift: Maximum head lift of 108 meters (354 feet).
- Multiple Filtration Mesh: Stainless steel filter mesh to prevent impurities, suitable for sand content less than 5%.
- Kompaktiškas dizainas: 3-inch diameter, suitable for well casings of 3 inches or larger.
- Pridedami priedai: 20m electric cord and 20m rope.
Image: Close-up of the pump's stainless steel discharge and connection, highlighting its robust construction.
Image: Diagram illustrating the internal copper motor with high-precision rotor and built-in overheat protection.
Sąranka ir diegimas
Tinkamas montavimas yra labai svarbus siurblio veikimui ir ilgaamžiškumui. Atidžiai atlikite šiuos veiksmus:
- Paruoškite šulinį: Užtikrinkite šulinio casing is at least 3 inches in diameter and free from debris.
- Attach the Rope: Securely attach the provided 20m rope to the designated sling holes on the pump. This rope will be used to lower and retrieve the pump.
- Connect Discharge Pipe: Connect a suitable discharge pipe (1-inch NPT) to the pump's outlet. Ensure a watertight seal.
- Elektros jungtis: Connect the 20m electric cord to a compatible power source (230V/50Hz). Ensure all connections are waterproof and meet local electrical codes.
- Nuleiskite siurblį: Carefully lower the pump into the well using the rope. Ensure the pump is fully submerged in water. Negalima let the pump rest on the bottom of the well; keep it suspended a few feet above the bottom to avoid drawing sediment.
- Pradinis patikrinimas: Before powering on, double-check all connections and ensure the pump is correctly positioned.
Image: Illustration demonstrating correct vertical installation where the pump is fully submerged, and a warning against operating without sufficient water.
Naudojimo instrukcijos
Įdiegus VEVOR giluminio gręžinio panardinamąjį siurblį, jį valdyti paprasta:
- Maitinimas: Connect the pump to the power supply. The pump will start operating automatically.
- Vandens srauto stebėjimas: Observe the water flow from the discharge. Ensure it is consistent and clear.
- Nepertraukiamas veikimas: The pump is designed for continuous operation as long as it is fully submerged and the water level is adequate.
- Apsauga nuo perkaitimo: The built-in overheat protection will automatically shut down the pump if it becomes blocked or overheats. If this occurs, disconnect power, allow the pump to cool, and investigate the cause before restarting.
Image: Operational diagram showing the submersible pump drawing water from a well, indicating a maximum flow of 35 L/min and a maximum head of 108m.
Priežiūra
Reguliarus siurblio aptarnavimas užtikrina optimalų veikimą ir prailgina jo tarnavimo laiką.
- Filtro tinklelio valymas: Periodically inspect and clean the stainless steel filter mesh to prevent clogging from sediment. For newly drilled wells with excessive granular sediment, consider adding a layer of gauze at the inlet.
- Patikrinkite, ar nėra žalos: Annually, or if performance degrades, retrieve the pump and inspect the casing, cable, and connections for any signs of wear, corrosion, or damage.
- Saugykla: Jei siurblys bus sandėliuojamas ilgesnį laiką, kruopščiai jį išvalykite, išleiskite visą vandenį ir laikykite sausoje, nuo šalčio apsaugotoje vietoje.
Vaizdas: Stambus planas view of the pump's multiple filtration mesh, designed to filter impurities. A tip suggests adding gauze for new wells.
Trikčių šalinimas
Dažniausiai pasitaikančias problemas ir jų sprendimus žr. šioje lentelėje:
| Problema | Galima priežastis | Sprendimas |
|---|---|---|
| Siurblys neįsijungia | No power; tripped circuit breaker; motor overheat protection activated; faulty wiring. | Check power supply; reset breaker; allow pump to cool and check for blockages; inspect wiring. |
| Mažas vandens srautas arba jo nėra | Low water level in well; clogged filter mesh; air in the system; discharge pipe blockage; worn impeller. | Check well water level; clean filter mesh; bleed air from system; clear pipe blockage; contact service for impeller replacement. |
| Siurblys veikia, bet nėra vandens | Pump not fully submerged; airlock; suction leak. | Ensure pump is fully submerged; prime the pump if possible (though submersible pumps are self-priming, air pockets can occur); check for leaks in the discharge line. |
| Siurblys dažnai įsijungia ir išsijungia | Low water level; pressure switch malfunction (if applicable); small leak in system. | Check well water level; inspect pressure switch; check for leaks in plumbing. |
Specifikacijos
Technical specifications for the VEVOR 3"-550 Deep Well Submersible Pump:
| Specifikacija | Vertė |
|---|---|
| Modelis | 3QGD1-60-0.55 (3"-550) |
| Medžiaga | Nerūdijantis plienas |
| Galia | 550 W |
| ttage | 230 V / Hz 50 |
| Maks. Srauto greitis | 2100 L/h (35 L/min) |
| Max. Head Lift | 108 m (354.3 pėdų) |
| Sand Resistance | Mažiau nei 5 proc. |
| Siurblio skersmuo | 7.6 cm (3 coliai) |
| Išleidimo dydis | 2.5 cm (1 inch) NPT |
| Electric Cord Length | 20 m |
| Included Rope Length | 20 m |
| Atsparus vandeniui klasė | IP68 |
| Darbinė temperatūra | 0–40 °C |
Image: Diagram showing key dimensions and performance curves of the VEVOR 3"-550 Deep Well Submersible Pump, including flow rate, head lift, power, and voltage.
Garantija ir palaikymas
The manufacturer's warranty information is not explicitly provided in the product details. For warranty claims or technical support, please contact VEVOR customer service directly or refer to the official VEVOR websvetainę.
Gamintojas: VEVOR
Modelio numeris: 3QGD1-60-0.55
UPC: 840281544639