AINOPE AV849

AINOPE Cable Bluetooth FM Transmitter User Manual

Modelis: AV849

Prekės ženklas: AINOPE

Produktas baigtasview

The AINOPE Cable Bluetooth FM Transmitter is designed to enhance your in-car audio experience by allowing you to stream music and make hands-free calls through your car's FM radio. It features fast charging capabilities for two devices simultaneously, an upgraded microphone for clearer calls, and a vibrant 7-color LED backlight.

AINOPE Bluetooth FM Transmitter with LED lights and charging ports

Figure 1: AINOPE Bluetooth FM Transmitter

Sąrankos instrukcijos

Follow these steps to set up your AINOPE Bluetooth FM Transmitter and connect it to your car's audio system.

Step 1: Find a Blank FM Frequency

Locate a "blank" or unused FM frequency on your car radio, typically between 88.1-107.9 MHz. A blank frequency will have no working radio station and will produce a slight rustle or white noise. This ensures optimal sound quality without interference.

Car radio display showing a blank FM frequency

Figure 2: Identifying a blank FM frequency on your car radio.

Step 2: Adjust FM Transmitter Frequency

Plug the FM transmitter into your car's cigarette lighter socket. Long press the "/CH" button on the transmitter to enter frequency adjustment mode. Use the joystick controller to adjust the transmitter's frequency to match the blank frequency you found on your car radio. Once synced, the sound from the transmitter should be very quiet, indicating a clear connection.

Hand adjusting the frequency on the AINOPE FM Transmitter

Figure 3: Adjusting the FM transmitter frequency to match the car radio.

Step 3: Pair Your Phone with the FM Transmitter

Įjunkite „Bluetooth“ savo mobiliajame telefone. Ieškokite available Bluetooth devices and select "AV849" (or similar model name) to pair. If prompted for a PIN, enter "0000". Once paired, you can stream audio from your phone to your car's speakers via the FM transmitter.

Smartphone screen showing Bluetooth pairing with the FM transmitter

Figure 4: Pairing your phone via Bluetooth.

Video Guide: Setup and Operation

Video 1: Official user guide for setting up and operating the AINOPE Bluetooth Car Adapter. This video demonstrates finding a blank FM frequency, adjusting the transmitter, and pairing your phone for audio streaming and calls.

Naudojimo instrukcijos

Garso reguliavimas

To adjust the audio volume, first increase the volume on your phone. If the volume is still too low, then adjust the volume on the FM transmitter using the joystick controller, and finally, adjust the volume on your car's speaker system. This three-step process ensures optimal sound output.

Hand adjusting volume on the AINOPE FM Transmitter

Figure 5: Adjusting the volume using the transmitter's controls.

Skambinimas laisvų rankų įranga ir balso asistentas

The built-in microphone and Bluetooth chip enable stable hands-free calls. Use the dedicated call button to answer, reject, or end calls with a single press. The transmitter also supports smart voice navigation from your phone, streaming audio from navigation apps, Siri, or Google Assistant directly to your car's speakers, enhancing driving safety.

AINOPE FM Transmitter with icons for Siri, Bixby, and Google Assistant

Figure 6: Voice assistant integration for hands-free operation.

LED foninio apšvietimo valdymas

The FM transmitter features a 7-color LED backlight. Short press the light/CH button two times to cycle through the breathing 7-color light mode, which adds ambiance and improves visibility in low light conditions.

AINOPE FM Transmitter showing different LED backlight colors

Figure 7: Demonstrating the 7-color LED backlight feature.

Gilių žemųjų dažnių režimas

Activate the Deep Bass Mode by pressing the 'b' button for enhanced bass sound, suitable for genres like Hip-Hop, Jazz, and Electronic Music. Press it again to return to Standard Mode for Pop, Light, R&B, Country, and Classic Music.

AINOPE FM Transmitter with 'b' button for deep bass mode

Figure 8: Switching between Standard and Deep Bass music modes.

Įkrovimo galimybės

The AINOPE FM Transmitter is equipped with advanced charging ports for rapid device charging.

  • PD 24W prievadas: Provides up to 24W output, capable of fast charging compatible devices like iPhone 15/14/13/12 and Pixel 3 up to 8 times faster than standard chargers.
  • QC 3.0 prievadas: Offers up to 18W output, charging compatible devices to 80% in approximately 35 minutes.
  • USB įkrovimo prievadas (5 V / 1 A): Can also be used as a USB flash drive port for music playback.

The total output when charging two devices simultaneously is 42W. Built-in protections include overcurrent, overvoltage, overcharge, overload, overheat, and short circuit protection to ensure safe charging.

AINOPE FM Transmitter showing PD 24W and QC 18W charging ports

Figure 9: Fast charging capabilities with PD and QC 3.0 ports.

Trikčių šalinimas

If you encounter issues with your AINOPE Bluetooth FM Transmitter, please refer to the following common problems and solutions:

ProblemaGalima priežastis / sprendimas
Static Noise / Poor Sound Quality
  • Interfered FM Frequency: Ensure your car radio is tuned to a truly "blank" frequency (no working station, slight rustle). Re-adjust the transmitter to this blank frequency.
  • Garsumo lygiai: Adjust volume in the sequence: Phone → FM Transmitter → Car Speaker. Ensure all are at appropriate levels.
  • Atstumas: Ensure your phone is within close range of the transmitter for stable Bluetooth connection.
Mažas garso lygis
  • Telefono garsumas: Increase the volume on your connected phone first.
  • Transmitter Volume: Use the joystick controller on the transmitter to increase its output volume.
  • Car Speaker Volume: Finally, increase the volume on your car's stereo system.
Difficulty Pairing Bluetooth
  • „Bluetooth“ įjungtas: Įsitikinkite, kad jūsų telefone įjungtas „Bluetooth“.
  • Įrenginio matomumas: Make sure the transmitter is powered on and in pairing mode (usually automatic upon power-on).
  • Pamiršti įrenginį: Jei anksčiau buvote suporuotas, pabandykite „pamiršti“ įrenginį telefono „Bluetooth“ nustatymuose ir suporuoti iš naujo.
  • PIN kodas: If prompted, enter "0000".
Įrenginys neįsijungia
  • Cigarečių degiklio lizdas: Ensure the car's cigarette lighter socket is clean and providing power. Test with another device if possible.
  • Saugus ryšys: Make sure the transmitter is firmly inserted into the socket.

Specifikacijos

FunkcijaDetalė
Modelio numerisAV849
Gaminio matmenys1.81 x 1.84 x 3.14 colio
Prekės svoris2.39 uncijos
Bluetooth versija5.0
Įvesties tomastageDC12V-24V
USB C Output (PD)24W MAX (5V/2.4A, 9V/2.5A, 12V/2A)
USB A Output (QC 3.0)18W MAX (5V/3A, 9V/2A, 12V/1.5A)
Bendra produkcija42W (when charging two devices)
LED Backlight7 Colors (Red, Green, Blue, Yellowish Green, Purple, Cyan, Silver White)
Ypatingos savybėsDeep Bass Mode, Enlarged Microphone, Voice Assistant Support, Voltmeter Display
SuderinamumasSmartphones, tablets, MP3 players, 12-24V vehicles

Saugos informacija

Always follow the instructions provided with the product. Do not use the product if the power cord or plug is damaged. Keep the product away from heat sources and liquids. Do not expose the product to extreme temperatures or humidity. Do not use the product while it is charging. Always unplug the product from the power source before cleaning it. Do not use the product if it has been damaged in any way. If the product malfunctions or if you notice any signs of damage, stop using it immediately and contact the manufacturer.

Garantija ir palaikymas

AINOPE provides a 24-month warranty and lifetime support for this product. If your cigarette lighter charger does not fit your car or does not work as expected, please feel free to contact the seller for a satisfying solution. Our philosophy is to serve every customer, and we are here to help you have a good experience with our products.

© 2024 AINOPE. Visos teisės saugomos.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.