USB and pedal cables (1, 2) should be routed through inner channels
Power and optional shifter cables (3, 4) should be routed through outer channels
Cables may be wrapped multiple times around cable management cleat to take in slack

INSTALLATION — XBOX ONE — PC

Attach power adapter and USB cables as shown
Every time your racing wheel connects with your system, it will rotate fully to each side and then to the center to calibrate
Your wheel will be ready once this calibration is completed For PC to enable the force feedback and RPM LED features on your G923 Wheel and Pedals you must install the Logitech G HUB software This can be found at logitechg.com/support/g923-xb1

MOUNTING CLAMPS

G923 Racing Wheel is equipped with a built in clamping system for mounting to a table
Push down and rotate clamp knobs to lock or unlock Rotate clamp knobs to tighten or loosen clamps
Note: Clamp extenders should be removed for attachment to thicker tables

BUTTONS

1 Left bumper
2 Directional pad
3 View button
4 Left stick button*
5 +/- Setting Adjustment buttons*
6 Right bumper

7 A, B, X, Y buttons
8 Menu button
9 Right stick button*
10 Setting Selection Dial and select button*
11 Xbox button

* requires supported games on Xbox One Assignable in any game on PC using either in-game assignment or Logitech G HUB software

FORCE FEEDBACK

Your Racing Wheel contains dual motors that will provide force feedback with supported games and systems
In supported titles you will also experience our next generation approach to force feedback: TRUEFORCE
TRUEFORCE integrates directly with game physics and audio to unlock high-definition, real-time force feedback Tire grip, suspension, weight, horsepower—even unique engine sound resonance—are immediately and accurately felt through the wheel
Supported titles on Xbox One and PC may implement TRUEFORCE high-definition force feedback For a list of supported titles visit logitechg com/support/g923-xb1

Note: Your Racing Wheel has an overheat protection circuit safeguard to protect it under high-temperature operating conditions
In rare instances, force feedback features may shut down during use while controls continue to operate
If this occurs, allow the wheel to cool down and power it down by unplugging it If this occurs frequently, contact product support

FEATURES

Clutch pedal
Brake pedal
Throttle pedal
Textured heel rest
Bolt mounting points (uses M6X1 bolts)
Patented carpet grip system
Carpet grip release clip
Push towards rear of pedal unit to release
Change pedal face position (requires 2 5mm hex key)

USING THE DUAL CLUTCH IN-GAME

Using a dual clutch system from a grid start in a race enables you to achieve maximum traction without the need to find the bite point of your clutch pedal – this can give you a significant advantage at the start of a race
To use the dual clutch system in-game:

At race start, fully depress the clutch pedal and the button assigned to the dual clutch function (see next section for setting instructions)
Select first gear using the Gear Up Paddle and fully depress the gas pedal
As soon as you get the green light for race start, immediatelyrelease the Dual Clutch button The car should start moving as the bite point of the clutch is engaged
Smoothly release your foot from the clutch pedal in order to
achieve maximum traction It’s worth practicing this last stepand modifying the bite point setting several times to find a method that works for you Once you have it perfected, this feature can help make up several places on the grid

Note: Support for the dual clutch function is not possible in some games A list of games that support the dual clutch feature can be found at logitechg com/support/g923-xb1

SETTING UP THE DUAL CLUTCH SYSTEM

Press and hold the left and right gear paddle and Left stick button and Right stick button together for two seconds to enter dual clutch setting mode The RPM LEDs will illuminate blue and flash slowly:Note: Whilst in the Dual Clutch setting mode the RPM LEDs will not respond to the game/SDK
Press the button you want to set as the dual clutch button The only valid buttons for this are the left stick button (LSB) and right stick button (RSB) The RPM LEDs will flash red to show that you’re in clutch position setting mode
While in your chosen simulation or game with the car still on a track, fully depress the clutch and gas pedals Engage first gear and keep pressing the minus button down until the car begins to move in-game You can adjust the precise bite point of the clutch by using the plus and minus buttons until you are happy with the setting
At this point you may test the dual clutch without leaving the setting mode It is recommended you attempt a race start, stop the car and adjust the bite point and then try again until you are satisfied with the performance of the dual clutch
Press the Select button in the middle of the dial on the wheel to exit dual clutch setting mode The RPM LEDs will flash in a sequence from green to blue to show that the setting is saved The RPM LEDs will then go out and begin responding again to RPM output from supported games

RESETTING DUAL CLUTCH SYSTEM
Press and hold the left gear shift, right gear shift, and X button for two seconds
The RPM LEDs will all flash four times and then extinguish to indicate that the Dual Clutch system has been reset
The button assigned to the Dual Clutch system (LSB or RSB) will revert to its normal function

USING LOGITECH G HUB
Logitech G HUB enables the following features on the G923:

Button programming with profiles that can be linked to games
Adjustment of wheel settings, such as Rotation Angle and TRUEFORCE strength
Testing of the various buttons, wheel and pedal functions

G HUB WHEEL SETTINGS
Sensitivity
Alters the output response of the wheel to be more or less sensitive Leaving this slider at 50% will provide a linear 1:1 output Between 51% and 100% will make the wheel increasingly more sensitive around the centre movement of the wheel Between 0% and 49% will make the wheel decreasingly sensitive around the centre movement of the Wheel

Operating Range
The G923 is capable of up to 900 degrees of rotation Reducing this setting will change the point at which the wheel will reach full steering lock This is especially useful if you’re driving a car with a smaller actual steering lock angle, such as a Formula 1 or GT3 car
Centering Spring (for games without force feedback) Most games that support force feedback already model the correct return to center function of the G923 based on the virtual car It is recommended that the Centering Spring option be turned off for tLhese games
Enabling the Centering Spring option will allow you to override the game features and adjust the strength of the return to center force using the provided slider
Torque
Only available for TRUEFORCE-supported games Torque controls the overall force feedback strength for your G923

Audio Effects Only available for TRUEFORCE-supported games Controls the overall strength of the audio-related effects (engine note, rumble strips etc ) when using TrueForcecompatible titles If you are using your G923 in older titles that do not support TRUEFORCE then adjustment of the force feedback can be performed from the settings menus of the game title
G HUB PEDALS SETTINGS

Sensitivity
Alters the output response of the pedals to be more or less sensitive Leaving this slider at 50% will provide a linear 1:1 output Between 51% and 100% will make the pedal
increasingly more sensitive around the initial movement of the pedal Between 0% and 49% will make the pedal decreasingly sensitive around the initial movement of the Pedal
Combined Pedals
If checked, this will set the gas and brake pedals to become two halves of a single axis This will help the pedals operate correctly in older racing titles that do not support separate axefor pedals
Note: if left checked then the pedals will not behave correctly in modern racing titles If you find that just one of your pedals is functioning by accelerating when pressed and braking when released then you should make sure that this option is not checked

TESTING YOUR WHEEL AND PEDALS
On the wheel and pedals screens in G HUB you can check every button and axis on your G923 in order to ensure everything is functioning correctly For the wheel you can also see the effect of altering the Operating range
QUESTIONS?
logitechG com/support/g923-xb1
© 2019 Logitech Logitech, Logitech G and the Logitech and Logitech G logos are trademarks or registered trademarks of Logitech Europe S A and/or its affiliates in the U S and other countries All other trademarks are the property of their respective owners Logitech assumes no responsibility for any errors that may appear in this manual
Information contained herein is subject to change without noticePlayseat

TAKE A SEAT AND DRIVE LIKE A CHAMPION

F1 RACING

BECOME YOUR OWN
F1 HERO AT HOME

VISIT PLAYSEAT.COM

CHALLENGE

FOLDABLE FOR
EASY STORAGE

VISIT PLAYSEAT.COM

SENSATION

SUPERIOR BUILD QUALITY,

STABILITY AND COMFORT

visit: playseat.com
11@ PLAYSEATGLOBAL

THE COLOR COLLECTION

Welcome to a fresh new take on gaming gear.
Logitech G performance and quality meet fun, vibrant colors. Playstyle matters. Choose yours.

Warning! Pedals have pinch points that may cause personal injury. Keep fingers, bare toes, and children away from pedals.
Warning! Wheel will automatically ~ adjust during setup, when adding power which may cause personal injury. During adjustment, keep hands, fingers, and children away from wheel. Important Safety, Compliance and Warranty lnforrnation Read Manual Before Product Use.
POWER SUPPLY WARNING! The power supply is for indoor use only.
Only use the power supply included with your product. Do not attempt to repair or use a damaged power supply. Do not immerse the power supply in water or subject it to physical abuse. Inspect the power supply regularly for cable, plug, and casing damage.
BATTERY WARNING !: Improperly replaced batteries may present a risk of leak or explosion and personal injury. Mistreated rechargeable batteries may present a risk of fire or chemical burn. Do not disassemble or expose to conducting materials, moisture, liquid, or heat above 54°( (130°F). Do not use or charge the battery if it appears to be leaking, discolored, deformed, or in any way abnormal. Do not leave your battery discharged or unused for extended periods Do not short circuit. Your device may contain an internal, rechargeable battery that is not replaceable. Battery life varies with usage. Non-operational batteries should be discarded according to local laws. If no laws or regulations govern, dispose of your device in a waste bin for electronics. Keep batteries away from children.
SAFE Usage Guidelines for Products

Do not open or modify the product except for battery removal and replacement.
Do not disassemble or attempt to service this product.
This product is safe under normal and reasonably foreseeable operating conditions.
If product is operating improperly, call Logitech support.

Product must be returned to the manufacturer for any service or repair.
This 1s not a Children’s Product and is not intended for use by children under 14 years old.
Long periods of repetitive motion using the product may be associated with nerve, tendon or muscle injury in Y<>t.fr hands, wrists, arms. shoulders, neck or back. See a qualified health professional for pain, numbness, weakness. swelling, burning, cramping, or stiffness. Please read the guidelines at http://www.logitech.com/comfort.
Use caution when operating moving parts.
WARNING! The product contains small. detachable parts, which may cause choking, personal injury, or death, especially in children. Please exercise care in the use and handling of small parts, and keep them away from children under 4 years of age.
For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

Use Guidelines: sate & Proper Use of Your Product:

Use the product with list1=d/certified ITE computers and accessories.
Connect power supply or power cord to a properly wired and grounded electrical outlet.
Disconnect the power source pnor to defeating or bypassing the equipment safeguard. RE?store the equipment safeguard before restoring power.

Warning. Risk of fire or explosion if the battery is replaced by an incorrect type. Ensure batteries are installed correctly by following the instructions provided. A battery subJected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
caution Connect all power cords to a property wired and grounded electrical outlet.
Moving parts. This product is not intended for use by children. Unplug this product when not in use for extend!)(! periods of time. Store product awa>J from children when not in use for extended periods of time.
Logitech Compliance. For Product Safety, EMC, RF and Energy information, go to www.logitech.com/compliance. Maintenance is not required for product compliance.
This product complies with relevant legal requirements for Restriction of Hazardous Substances (RoHS) and management of waste electronic and electrical equipment (WEEE) in the EU, Turkey, Ukraine, United A@b Emirates, India, China and Taiwan. For RoHS and WEEE information, go to www.logitech.com/compliance. lt -0
Batteries, electronic and electrical equipment should not be disposed of with household waste. Wherever possible, they should be segregated and brought to an appropriate collection point to enable recycling and avoid potential impacts on the environment and human health. For more information, contact your local authorities or place of purchase, or visit www.logitech.com/recycling.

FCC statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. And, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Warning: Where shielded interface cables or accessories have been provided with the product or specified additional components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to ensure compliance with FCC. Changes or modifications to product not expressly approved by Logitech, Inc could void your right to use or operate your product by the FCC.
IC statement :

CAN ICES-3 (B) / NMB-3 (B)
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement
This wireless product complies with the FCC and Industry Canada RF exposure limit for portable devices.
Logitech Limited Hardware Product Warranty- A Summary Logitech warrants that its hardware product shall be free from defects in materials and workmanship for the length of time identified on your product package beginning from the date of the original retail purchase. See support.logitech.com for specific warranty information about your product and procedures to act on a warranty claim. Logitech’s entire liability and your exclusive remedy for any breach of warranty shall be, at Logitech’s option, to repair or replace a functional eQu1valent of the product, or to refund the price paid, if the hardware is returned to the point of purchase or such other place as Logitech may
direct along with a receipt. Warranty protections are in addition to rights provided under local consumer laws and may vary among countries. See full warranty information to know your consumer rights and the additional protections provided by this product warranty.

Logitech Address: Log1tech, Inc., 7700 Gateway Blvd. Newark, California
94560. Full Warranty Information: support.logitech.com

Visit IogitechG.com and follow @logitechG to find out more.
Visita logitechG.com y sigue a @logitechG para averiguar mos.

Documents / Resources

logitech G923 Racing Wheel and Pedals for Playstation 4 [pdf] User Guide
G923 Racing Wheel and Pedals for Playstation 4, G923 Racing Wheel and Pedals, Playstation 4 Racing Wheel and Pedals, Racing Wheel and Pedals, Racing Wheel, Racing Pedals