ZigBee Smart plug
ຄູ່ມືຜູ້ໃຊ້

ແນະນຳຜະລິດຕະພັນ

ນ້ໍາຫນັກຂອງອຸປະກອນແມ່ນຫນ້ອຍກວ່າ 1 ກິໂລກໍາ. ຄວາມສູງຂອງການຕິດຕັ້ງຫນ້ອຍກວ່າ 2 m ແມ່ນແນະນໍາໃຫ້.

ຄໍາແນະນໍາການຕິດຕັ້ງ

1. ປິດເຄື່ອງ ເພື່ອຫຼີກເວັ້ນການຊ໊ອກໄຟຟ້າ, ກະລຸນາປຶກສາຕົວແທນຈໍາຫນ່າຍຫຼືຜູ້ຊ່ຽວຊານທີ່ມີຄຸນວຸດທິສໍາລັບການຊ່ວຍເຫຼືອໃນການຕິດຕັ້ງແລະສ້ອມແປງ.
2. ຄໍາແນະນໍາສາຍໄຟ
   ໃຫ້ແນ່ໃຈວ່າສາຍໄຟຖືກຕ້ອງກ່ອນທີ່ຈະເປີດອຸປະກອນ. S1/S2 can connect with the rocker light switch, or it doesn’t connect. To ensure safety, do not connect the neutral wire and live wire to it.

ຂໍ້ມູນຈໍາເພາະ

ຄຸນສົມບັດ

ZigBee plug is a smart Plug that adopts the ZigBee plug wireless protocol and connects to your internet through the ZigBee hub. You can turn on/off, schedule on/off, and share the device with your family to control together, and so on.

ການຄວບຄຸມໄລຍະໄກ	ຕາຕະລາງ ກຳ ນົດເວລາ
ການຄວບຄຸມສຽງ	ແບ່ງປັນການຄວບຄຸມ
ສາກແບບ Smart

The above functions are determined by the ZigBee Hub.

ຄໍາແນະນໍາການດໍາເນີນງານ

1. ດາວໂຫລດ APP
   Please refer to the user guide of the hub to download the corresponding APP. below platforms are recommended:

   SmartThings	Amazon Alexa	ເຫ້ວ

2. ການເຊື່ອມຕໍ່ Hub
   Set the hub according to the user guide. Support ZigBee plug hubs as follows:
   Echo Studio
   Echo Plus (ແບບ: ZE39KL)
   2nd Gen Echo Show (ແບບ: DW84JL)
   ຮຸ່ນທີ 2 Echo Plus (ຮຸ່ນ: L9D29R)
   ສູນ Samsung SmartThings
   Philips Hue
   ຖ້າການເຊື່ອມຕໍ່ລົ້ມເຫລວ, ກະລຸນາຍ້າຍສູນໄປໃກ້ໂທລະສັບຂອງທ່ານແລ້ວລອງໃໝ່ອີກຄັ້ງ.
3. ເປີດເຄື່ອງ
   ຫຼັງຈາກເປີດເຄື່ອງແລ້ວ, ອຸປະກອນຈະເຂົ້າສູ່ໂໝດການຈັບຄູ່ໃນລະຫວ່າງການໃຊ້ຄັ້ງທຳອິດ, ແລະສັນຍານໄຟ LED ຈະກະພິບ.
    The device will exit the pairing mode if no next operation for a long time. If you enter again, please long-press the manual switch for 5s until the LED signal indicator flashes and release.
4. ເຊື່ອມຕໍ່ກັບ Alexa
   1. Power on the Plug
   2. Ask, “Alexa, discover devices!
   3. Plug ashes once it’s connected
   4. Wait until Alexa finishes, check the new devices” First/Second….plug”

ເຊື່ອມຕໍ່ກັບ SmartThings

1. Power up the smart bulb, bulb breathe 3 times, and enter the configuration state.
2. Open the SmartThings app, and click”+”, click “Device”, click “SmartThings”, click “Lighting”, click ” Smart Bulb”, click “Start”, click “Next”, click “Skip the step”, click “Done”

ຣີເຊັດເປັນຄ່າໂຮງງານ

Long-press the configuration button for 5s until the LED signal indicator flashes and release, then the reset is successful. The device enters spairing mode.

If you pair the device with the hub again, please reset the device to factory default.

ຜະລິດຢູ່ໃນປະເທດຈີນ

ເອກະສານ / ຊັບພະຍາກອນ

ໂມດູນສະຫຼັບແສງ ZigBee [pdf] ຄູ່ມືຜູ້ໃຊ້ ໂມດູນສະວິດໄຟ, ໂມດູນສະຫຼັບ, ໂມດູນ

ເອກະສານອ້າງອີງ

• ຄູ່ມືຜູ້ໃຊ້