TOGUARD CE18A Dash Camera User Manual
TOGUARD CE18A Dash Camera

ແຈ້ງການສໍາຄັນ

  • This product is intended for using in motor vehicles only. Do NOT install the camera where it might block the driver’s view of road (including the mirrors) or the deployment of the airbag.
  • Before using this device, please insert the memory card first, and need to format micro SD card to FAT32 format on PC firstly, then format the memory card in camera menu.
  • This camera records video at high resolution. Be sure to use high speed Micro SD card (Class 10 or above). 16 GB or 32 GB Micro SD card is recommended.
  • safety reasons, this camera has a small built-in battery, which is used to save the video file after external power supply cuts off (car turns off).
  • Be sure the camera lens is clean and there is nothing blocking the lens.
  • DO NOT leave the camera in direct sunlight for a long period of time or where the temperature could go above 140°F(60°C).

ການໂຕ້ຕອບແລະຟັງຊັນປຸ່ມ

ການໂຕ້ຕອບແລະຟັງຊັນປຸ່ມ
ການໂຕ້ຕອບແລະຟັງຊັນປຸ່ມ

Function ປຸ່ມ

  • ພະລັງງານ
    • When the camera is off, press and hold power button to turn on the camera.
    • Under any mode, press and hold power button to turn off the camera.
    • When the camera is on, short press to turn on/off screen display.
  • ເມນູ
    • In Video / Photo / Playback mode, short press to enter setup menu for that particular mode, short press again to access System Setup Menu.
    • During video recording, short press to manually lock/ unlock current video.
    • In Standby, press and hold to switch working mode.
  • Up
    • During video recording, short press to turn ON/OFF audio recording.
    • In setup menu, short press to select options and adjust values.
    • In Playback, short press to select files.
  • ລົງ
    • In setup menu, short press to select options and adjust values.
    • In Playback, short press to select files.
    • In the recording state, short press the down button to switch the recording screen.
  • OK
    • In Video Mode. short press to start/stop recording.
    • In Photo Mode. short press to take a photo.
    • In Setup Menu, short press to confirm selection and changes.
    • In Playback Mode. short press to play a video file.
  • ຕັ້ງ​ຄ່າ
    • Short press to reset the camera to factory default status.

Set up and Installation

Set up and Installation

  1. Before installation, please check the camera’s normal function, and make sure you are using a high speed Micro SD card (speed Class 10 or above),and format the card in the camera menu before recording.
  2. Use the suction cup mount to install the CE18A dash cam on the windshield. The recommended place is near the rearview mirror facing front, adjust the lens angle for best coverage
  3. .Adjust the lens angle of the camera, make sure you get the best coverage over the hood and the road ahead, so you can record what happens.
  4. Connect the power to the camera and the cigarette lighter, hide the rest of the cable in the gap of the interior trim board.

ຮູບແບບການເຮັດວຽກ

The CE18A operates in 3 modes: Video Recording Mode, Photo Mode and Playback Mode. These modes also have menu to help you configure recording and taking photos. Press and hold “Menu” to switch between different modes and access to the mode you want. Watch the icon on top left corner of the screen for each mode.

ຮູບແບບການບັນທຶກວິດີໂອ

The camera will automatically enter Video Recording Mode and start recording when connected to a car charger and power on. A Red dot flashing on the top left corner indicates recording is in progress. Press the OK to stop recording, or start recording again.

In all 3 operating mode, you can press the Menu button once to access the menu settings for that particular mode, and press twice to display System Setting Menu. The System Setting Menu is common to all modes.

Press UP and DOWN to scroll through the various setting options and press OK to select and confirm selection, Press MENU again to exit the setting menu.

ຮູບແບບການບັນທຶກວິດີໂອ

  1. ຮູບແບບວີດີໂອຮູບແບບ
  2. ສະຖານະພາບການບັນທຶກ Loop
  3. Motion Detection
  4. ຕົວຊີ້ວັດການບັນທຶກ
  5. Video Lock Status
  6. WDR Status
  7. G-Sensor Status
  8.  ຄວາມຍາວການບັນທຶກ
  9. Video Resolution
  10. ຫນ້າຈໍຫລັງ
  11. ສະຖານະພາບຕິດຕາມບ່ອນຈອດລົດ
  12. ສະຖານະພາບບັດຄວາມ ຈຳ
  13. ສະຖານະພາບພະລັງງານ
  14. ປ້າຍລົດ
  15. ສະຖານະພາບການບັນທຶກສຽງ
  16. ວັນແລະເວລາ

Video Recording Menu

Video Recording Menu

ການແກ້ໄຂ: Adjust recording video resolution, 1080P/ 720P/ VGA available. When connected to the rear camera, recording video resolution: 1080P+720P/720P+720P/VGA+VGA Loop Recording: This function allows you to set video length to 1/3/5minutes, select a value to activate loop recording, so when storage is full, it will automatically loop back to the earliest file and record over it.
WDR: Wide Dynamic Range: turn on to optimize video quality with wider light range and image details.
ການກວດຈັບການເຄື່ອນໄຫວ: Turn ON/OFF motion detection function. In the video mode, in the standby state, when the front camera screen changes, the driving recorder will automatically record for 11 seconds .

Video Recording Menu
ສຽງບັນທຶກ:
Turn ON/OFF audio recording in video. Date Stamp : Enable/Disable the date and time marks in video files.
G-Sensor: G-sensor will detect significant or sudden shock and movement, then automatically locks current file from loop recording. Low/Medium/High sensitivity available.
ຕິດຕາມກວດກາບ່ອນຈອດລົດ: It’s used to protect your car after parking. With this function on, after you stop the car and the camera turns off, it stays standby. When camera detects collision, it will automatically turn on and take a short video, then shut down automatically.
ເບີລົດ: Turn on to stamp your car plate number in video.

Photo Taking Mode

The CE18A camera can operate in Photo Taking Mode, and take HD photo up to 12 Mega pixels.

ເພື່ອຖ່າຍຮູບ:

Simply power on the CE18A camera. Press Mode to select Photo Mode, and press OK to take photo.
Like the Video Recording Mode, you can press the menu button once to access the setting menu for Photo Mode, press menu twice to enter system setting menu.

Photo Taking Mode

  1. ຮູບແບບຮູບພາບ
  2. ຕ້ານ Shake
  3. Photo Resolution
  4. Photo Counts
  5. ສະຖານະພາບບັດຄວາມ ຈຳ
  6. ສະຖານະພາບພະລັງງານ
  7. Date& Time

Photo Mode Menu

ການແກ້ໄຂ: Set the photo resolution, Up to 12MP available.
ຕ້ານ Shake: Turn on to stabilize photo, reduce shaking.
ວັນທີ Stamp: Enable/Disable the date and time stamp in photo.

ຮູບແບບການຫຼິ້ນ ໃໝ່

ຮູບແບບນີ້ອະນຸຍາດໃຫ້ທ່ານສາມາດຫຼິ້ນຄືນວິດີໂອທີ່ບັນທຶກໄວ້ຫຼື view ຮູບພາບ.

  1. Stop video recording, press and hold Menu button twice to switch to Playback Mode.
  2. ໃຊ້ປຸ່ມຂຶ້ນແລະລົງເພື່ອເລື່ອນຜ່ານບັນທຶກໄວ້ files/ photos, ແລະກົດຕົກລົງເພື່ອ view ວິດີໂອທີ່ບັນທຶກໄວ້.

ເມນູການຫຼິ້ນ

After choosing a recorded video or photo, press the Menu button once to access the setting menu for Playback Mode.

ເມນູການຫຼິ້ນ

ລຶບ: ລຶບປະຈຸບັນ file displayed or delete all files.
ການປົກປ້ອງ: Lock/Unlock the current file displayed or Lock/ Unlock all files.
ພາບສະໄລ້: Select a time gap to activate this function, and all recorded file will be displayed in slide show.

ເມນູການຕັ້ງຄ່າລະບົບ

Press MENU button twice to access System Setting Menu in any mode. The TOOL icon is highlighted in the upper left corner.

ເມນູການຕັ້ງຄ່າລະບົບ

ເຄື່ອງປະຫຍັດ ໜ້າ ຈໍ: ຕັ້ງເວລາໃນການປິດຈໍສະແດງ LCD ໂດຍອັດຕະໂນມັດພາຍຫຼັງບໍ່ມີການເຮັດວຽກ.
ພະລັງງານອັດຕະໂນມັດ: Set the time for the camera to automatically power off to save energy. After the camera is idle for set time, it will power off.
ຄວາມຖີ່: Set light frequency to 50Hz or 60Hz, and press OK. Beep Sound: Turn on/off sounds when you press any buttons.

ເມນູການຕັ້ງຄ່າລະບົບ
ພາສາ:
Chinese/English/Japanese/Deutsh/French/ Italian/Spanish
ວັນທີ່ / ເວລາ: Change the time and date by using the UP and DOWN button, then press OK to confirm.
ຮູບແບບ: Format the Micro SD card.
ການຕັ້ງຄ່າເລີ່ມຕົ້ນ: Reset all settings back to factory default.
Version: ກວດສອບລຸ້ນ firmware.

ຂໍ້ມູນ

ຮູບແບບ Toguard  CE18A
ເຊັນເຊີຮັບພາບ ເຊັນເຊີຄວາມລະອຽດສູງ CMOS
ຫນ້າຈໍ ຈໍ LCD 2.45 ນິ້ວ
ທັດສະນະທີ່ 170°  High-Resolution Wide Angle Lens
Video  Resolution 1920*1080P+1280*720P/
1280*720P+1280+720P/
640*480P+640*480P
ຮູບແບບວິດີໂອ MOV
ລະຫັດວິດີໂອ H.264
Picture  Format JPG
Photo  Resolution 12MP / 10MP / 8MP / 5MP /3MP/2MP/

1.3MP/VGA

Loop Recording ສະຫນັບສະຫນູນ
Power on recording ສະຫນັບສະຫນູນ
WDR ສະຫນັບສະຫນູນ
ລັອກ G-Sensor ສະຫນັບສະຫນູນ
ພາສາ Chinese/English/Japanese/Deutsh/ French/Italian/Spanish
ການບັນທຶກສຽງ ໄມໂຄຣໂຟນຕິດຕັ້ງ, ເປີດ / ປິດໄດ້
ການເກັບຮັກສາ ບັດ Micro SD (ສູງສຸດ 32GB)
USB interface Mini USB
ລະ​ບົບ​ປະ​ຕິ​ບັດ​ການ Windows 7/10 ຫລື MAC
ພະລັງງານພາຍໃນ ແບດເຕີຣີ Li-ion ກໍ່ສ້າງ
ການສະ ໜອງ ພະລັງງານພາຍນອກ ຊິງຕັນດີຊີ 5V / 1.5A
ອຸນຫະພູມການເກັບຮັກສາ -4 ° F ~ 140 ° F (-20 ° C ~ 60 ° C)
ອຸນຫະພູມປະຕິບັດການ 14°F~122°F(-10°C~50°C)

ບັນຫາທົ່ວໄປແລະວິທີແກ້ໄຂ

  • Q: Even though set the screen saver, but the screen will randomly.
    A: The power supply might not be stable, please change another car charger to try.
  • Q: Why dash cam drain car battery?
    A: Please check whether the cigarette lighter still be on after you turn off car engine.
  • Q: The camera keeps starting and off?
    A: That could be the parking monitor function being triggered, check the setup menu.
  • The dash cam will stop automatically while recording.
    1. A: Check whether the memory card is full.
    2. Check whether the Micro SD card is high-speed above C10.
    3. ກວດເບິ່ງບັດຄວາມ ຈຳ, ອາດຈະມີວິດີໂອລັອກຫລາຍເກີນໄປທີ່ການບັນທຶກ loop ຈະບໍ່ສາມາດໃຊ້ໄດ້.
    4. Check the car charger connection status, if the connection is loose, the power supply is not stable, the camera will automatically turn off.
  • If the video played on the computer is somehow not fluent or jammed.
    • A: Try to play the video with other video players, like : Pot player or VLC player.
    • ຈັດຮູບແບບ SD Card Micro ຂອງທ່ານໄວ້ໃນກ້ອງຖ່າຍຮູບ.
    • Run speed test on the memory card to make sure the memory card fits the requirement: Write Speed is over 10MB/S.
  • Q: There are stripes interference in the image. There should be wrong light frequency.
    A: According to the local main frequency, make the appropriate settings 50HZ or 60HZ.
  • Suction mount cannot attach on windshield well?
    1. A: Please clean the windscreen where attaching with a glass cleaning wipe. Removed the protective film, If it does not work, warming your windscreen then try it again.
    2. Please soak suction mount to warm water for a moment.
    3. If it is still not working, we are glad to send a new suction mount to you, please contact us ([email protected]) to get a replacement.
  • Q: Without external power supply, the camera only lasts very short time, or it just can’t turn on.
    A: The built-in battery is very small for safety reasons, not designed to work alone, so please keep it connected to external power supply.
  • Q: When connect the camera with PC by USB cable, it will show “Mass Storage” and “PC Camera”, I ສາມາດເຮັດໄດ້not do any thing.
    A: In this situation, you can directly playback video on PC. If you want to operate camera, please connect it with cigarette lighter by car charger we provided.

Not having a positive experience?

ກະລຸນາຕິດຕໍ່ຫາພວກເຮົາໂດຍ

[email protected]

We will offer prompt and authoritative reply within 24 hours and try our best to resolve your problem ASAP. More Safe Guarantee with Toguard!

 

ເອກະສານ / ຊັບພະຍາກອນ

TOGUARD CE18A Dash Camera [pdf] ຄູ່ມືຜູ້ໃຊ້
CE18A Dash Camera, CE18A, Dash Camera

ອອກຄໍາເຫັນເປັນ

ທີ່ຢູ່ອີເມວຂອງທ່ານຈະບໍ່ໄດ້ຮັບການຈັດພີມມາ.