MEAN WELL NPB-450 Series 450W High Reliable Ultra Wide Output Range Intelligent Battery Charger User Manual

ໂລໂກ້ MEAN WELL

NPB-450 Series

ຄຸນ​ລັກ​ສະ​ນະ

  • Patented auto ranging with ultra-wide charging voltage (10.5~21V,21~42V,42~80V, 54~100V; Please refer to page 8 for setting)
  • ອະນຸສັນຍາ CANBus ທີ່ມີໃນຕົວສໍາລັບການຄວບຄຸມ, ການຕັ້ງຄ່າແລະການຕິດຕາມ
  • ສາມາດຕັ້ງໂປຣແກຣມໄດ້ 2/3 ວິນາທີtage ແລະເສັ້ນໂຄ້ງການສາກໄຟຜ່ານ SBP-001
  • ການຕັ້ງຄ່າຄູ່ມືສໍາລັບ 2/3 stage ແລະ 4 ເສັ້ນໂຄ້ງການສາກໄຟໃນຕົວຜ່ານ DIP SW
  • Multiple protections:
    Short circuit / Over voltage / Over temperature/ Battery under voltage/ Battery reverse polarity (No damage)
  • ເຄື່ອງສາກຕົກລົງ ແລະ ສັນຍານແບັດເຕີຣີເຕັມ
  • ຟັງຊັນການຊົດເຊີຍອຸນຫະພູມເພື່ອຍືດອາຍຸຂອງຫມໍ້ໄຟ (Lead-acid ເທົ່ານັ້ນ)
  • -30°C~+70°C wide operating temperature
  • ພັດລົມ DC ຄວບຄຸມຄວາມຮ້ອນສໍາລັບການຫຼຸດຜ່ອນສຽງ
  • ການຄວບຄຸມ ON / OFF ໄລຍະໄກ
  • Smart programmer available (Order NO.: SBP-001, sold separately)
  • ເຄື່​ອງ​ມື​ຖື​ທີ່​ມີ​ຢູ່ (Order NO.: DS-Carry handle, ຂາຍ​ແຍກ​ຕ່າງ​ຫາກ)
  • ປະຕິບັດຕາມ 62368-1 + 60335-1/-2-29 ການຢັ້ງຢືນຄູ່
  • ເຫມາະສໍາລັບແບດເຕີຣີ້ອາຊິດນໍາ (Pb) ແລະ li-ion
  • 3 ປີຮັບປະກັນ

ຄໍາຮ້ອງສະຫມັກ

  • AGV
  • E-Bike, E-Scooter, ຄampໃນລົດ, ລົດເມ, ຍານພາຫະນະພິເສດ
  • ເຄື່ອງຕັດຫຍ້າຫຸ່ນຍົນ
  • ຫຸ່ນຍົນຊັກ
  • ຫັດຖະກໍາການພັກຜ່ອນ, yacht ສ່ວນບຸກຄົນຫຼືເຮືອເຮັດວຽກ
  • ລະບົບເຝົ້າລະວັງ
  • ສະຖານີໂທລະຄົມ
  • ວິ​ທະ​ຍຸ​ການ​ແກ້​ໄຂ​ສໍາ​ຮອງ​ຂໍ້​ມູນ​ລະ​ບົບ​
  • Equipments or instruments with backup battery

ລາຍລະອຽດ

NPB-450 ເປັນຊຸດຂະໜາດນ້ອຍ, ຫຼາກຫຼາຍຊະນິດ, ແລະກວ້າງສຸດtage intelligent charger. It utilizes a fully digital control design with patented automatic battery voltagເຕັກ​ໂນ​ໂລ​ຊີ​ການ​ກວດ​ສອບ e​, ມີ​ຫ້າ​ລັກ​ສະ​ນະ​ທີ່​ສໍາ​ຄັນ​ລວມ​ທັງ​ອັດ​ສະ​ລິ​ຍະ​, versatile​, ຜູ້​ເປັນ​ມິດ​, ຄວາມ​ປອດ​ໄພ​, ແລະ​ຫນາ​ແຫນ້ນ​. ຊຸດມີສີ່ແບບທີ່ມີຜົນຜະລິດ voltage ranges of 10.5~21V, 21~42V, 42~80V, and 54~100V respectively. The charging voltage ຊ່ວງຂອງແຕ່ລະແບບແມ່ນກວ້າງພໍທີ່ຈະກວມເອົາຄວາມຫລາກຫລາຍຂອງແບດເຕີລີ່ທີ່ແຕກຕ່າງກັນtages ແລະເຄມີສາດຫມໍ້ໄຟ, ແລະມີ vol ອັດສະລິຍະກໍ່ສ້າງໃນtage ໂໝດການສາກໄຟກວດພົບ (ໝາຍເຫດວ່າ ໂໝດນີ້ຖືກຕັ້ງເປັນປິດຕາມຄ່າເລີ່ມຕົ້ນຈາກໂຮງງານ ແລະ ເໝາະສຳລັບແບັດເຕີຣີ lithium ທີ່ມີ BMS ເທົ່ານັ້ນ). NPB-450 ສາມາດຈັບຄູ່ກັບໂປແກມ SBP-001 ຂອງ MEAN WELL ສໍາລັບການຕັ້ງຄ່າດິຈິຕອນ, ເຊັ່ນ: ເລືອກ 2/3 s.tage ການສາກໄຟ, ປັບການສາກໄຟ voltage/Current, ແລະຕັ້ງເວລາຮອບວຽນການສາກໄຟເພື່ອປົກປ້ອງອາຍຸແບັດເຕີຣີ. ໂດຍຜ່ານ DIP SW ທີ່ເປັນມິດກັບຜູ້ໃຊ້ຢູ່ໃນແຜງດ້ານຫນ້າ, ຜູ້ໃຊ້ອາດຈະປັບຕົວໂດຍກົງ 2/3 ວິນາທີtage ການສາກໄຟ, ປະຈຸບັນ (50 ~ 100%), ແລະເລືອກລະຫວ່າງ 4 ປະເພດຂອງເສັ້ນໂຄ້ງການສາກໄຟທີ່ກໍານົດໄວ້ກ່ອນ. ນອກຈາກນັ້ນ, ໂປໂຕຄອນການສື່ສານ CANBus ໄດ້ຖືກສ້າງຂື້ນເພື່ອຕອບສະຫນອງຄໍາຮ້ອງສະຫມັກທີ່ເປັນມືອາຊີບ, ເຊິ່ງຊ່ວຍໃຫ້ການຄວບຄຸມຫ່າງໄກສອກຫຼີກແລະການຕິດຕາມສະຖານະຂອງເຄື່ອງຊາດ. ໃນແງ່ຂອງຄວາມປອດໄພ, ມັນມີການກວດສອບອັດສະລິຍະສໍາລັບຫມໍ້ໄຟທີ່ເຫມາະສົມ voltage and connection as well as protection from reverse polarity. It passes ITE IC/EN/UL62368-1 and household appliances EN60335-1/-2-29 dual safety and 3-year warranty to guarantee reliable operation. The NPB-450 is truly an intelligent, safe, and reliable universal charger with outstanding cost performance.

ການເຂົ້າລະຫັດແບບ ຈຳ ລອງ

ຂໍ້ມູນ

ຂໍ້ມູນ

ລາຍລະອຽດຕໍ່ເນື່ອງ

ຕັນແຜນວາດ

PFC fosc: 80KHz
PWM fosc: 60KHz

ຕັນແຜນວາດ

ເສັ້ນໂຄ້ງ Derating

ເສັ້ນໂຄ້ງ DeratingDerating Curve Continued

ຄຸນລັກສະນະຄົງທີ່

ຄຸນລັກສະນະຄົງທີ່

ຄູ່ມືການໃຊ້ງານ

1. ການຕັ້ງຄ່າດ້ວຍຕົນເອງ

ການຕັ້ງຄ່າດ້ວຍຕົນເອງ

1.1 2 or 3-stage selectable via DIP S.W on panel

2 ຫຼື 3-stage selectable via DIP S-W on panel

1.2 Charging curve can be adjustable via DIP S.W on panel

Charging curve can be adjustable via DIP S-W on panel

  • The default curve is programmable, whereas other pre-defined curves can be activated by the means of the DIP S.W; This series provides 2 or 3 stage charging curve please refer to the table below and the Mechanical Specification.

Charging curve can be adjustable via DIP S-W on panel continued

2. Programmable charging curve

Charging Curve can be set via SBP-001 with computer

1 ຂັ້ນຕອນ

ການຕັ້ງຄ່າຮາດແວ

ການຕັ້ງຄ່າຮາດແວ

2 ຂັ້ນຕອນ

Connect to software for setting

Connect to software for setting

Connect to software for setting continued

ລາຍລະອຽດ ໜ້າ ທີ່:

SBP-001 is a programmer, particularly for MEAN WELL’s various programmable battery charger models to program the parameters of charging curves, such as the 2 or 3 stage selectable, Constant current (CC), tapper current(TC), Constant voltage (CV), float voltage (FV),Charging time out and so on, to accommodate the diversified battery specification in industry. With the design accounting for simplicity and convenience, users can easily configure MEAN WELL’s programmable battery chargers with SBP-001 programmer and the computer; all of the setups are able to be finished easily by the means of the specific software.
Note:(1) Tapper current(TC) default is 10%, can be fine tuned from 2% to 30% by SBP-001 with computer or CANBus Interface.
(2) Please contact MEAN WELL for more details.

※ Software Interface:

ການໂຕ້ຕອບຊອບແວ

3. Auto Ranging for Charging (Default non-Auto ranging)

※ Function Description:

a. NPB-450 has built-in auto ranging mode.
(Note this mode is set to OFF by factory default and is suitable for lithium batteries with BMS only)

b. When operating in auto ranging mode , NPB-450 will automatically detect the voltage of battery that is connected and adjust charging voltage accordingly. It will not start charging unit appropriate battery voltage ຖືກກວດພົບ.

c. While under auto ranging mode, NPB-450’s built-in MCU will adjust charging voltage. There is no potentiometer for voltage adjustment on the front panel.

d. While under auto ranging mode, the charging current can be adjusted between 50~100%. (The charging current can not be adjusted via potentiometer while not operating in auto ranging mode)

※ When using the auto ranging charging curve function, please pay attention to the following:

Input-Output Side

  1. Default factory setting is OFF via DC output side DIP S.W, Follow steps A1~A6 below to enable the setting.
  2. Auto ranging function should use together with Lithium batteries and BMS (Battery Management System).
  3. Do not exceed the output voltage and current ranges as specified in the NPB-450 specifications (please refer to page 2).

※ Auto Ranging function by DIP S.W Setting

Auto Ranging function by DIP SW Setting

※ Back to non-auto ranging as following:

Non-auto ranging

4. Auto Derating function

※ Covered by over temperature protection, auto de-rating function works under operation either in charging curve (2 or 3 stage) or under control by communication protocol(CANBus).

T1(Typ.): Maximum ambient temperature of 100% output current.
T2(Typ.): T1+5℃.

Auto Derating function

5. CANBus communication interface

CANBus 2.0B version, Can control, setting and monitoring that including output charging voltage, output charging current, internal temperature and DC output ON/OFF……and so on, please refer to the ຄູ່ມືຜູ້ໃຊ້ ສໍາລັບລາຍລະອຽດເພີ່ມເຕີມ.

CANBus communication interface

CANBus communication interface continued

6. Charger OK Signal

Charger OK signal is a TTL level signal.
The maximum sourcing current is 10mA.

Charger OK Signal

7. Battery Full Signal

Battery full signal is a TTL level signal.
The maximum sourcing current is 10mA.

Battery Full Signal

8. Remote ON-OFF Control

The NPB-450 can be turned ON/OFF by using the “Remote Control” function.

ການຄວບຄຸມ ON-OFF ໄລຍະໄກ

※ The charger is shipped, by factory default, with Remote ON-OFF(pin 7) and +12Vaux (pin 8) shorted by connector.

Remote ON-OFF Control continued

9. Temperature compensation (3 stage ເທົ່ານັ້ນ)

Temperature compensation function to prolong battery life for lead-acid batteries. Temperature compensation range is 0 ~ 40℃.
The battery temperature sensor comes along with the charger can be connected to the unit to allow temperature compensation of the charging voltage.
If the sensor is not used, the charger works normally.

ການຊົດເຊີຍອຸນຫະພູມ

10. DC Output Side LED Indicators & Corresponding Signal at Function Pins

DC Output Side LED Indicators

ການສະເພາະດ້ານກົນຈັກ

※ Intelligent Battery Charger model

Intelligent Battery Charger model

※ DIP S.W

DIP SW

※ Control Pin No. Assignment : HRS DF11-14DS or equivalent

Control Pin No Assignment

※ LED Status Table

ຕາຕະລາງສະຖານະພາບ LED

※ Connector Pin No. Assignment : HRS DF11-14DS or equivalent

Connector Pin No Assignment

ຟັງຊັນ Pin

Note1: Non-isolated signal, referenced to [GND(signal)].
Note2: Isolated signal, referenced to GND-AUX

ບັນຊີເຄຶ່ອງອຸປະກອນເສີມ

※ NTC Sensor and Remote Control mating along with NPB-450 (Standard accessory)

ບັນຊີເຄຶ່ອງອຸປະກອນເສີມ

※ Carry handle (Optional accessory, battery charger and pull handle should be ordered seperately)

Accessory List Continued 1

Accessory List Continued 2

ຄູ່ມືການຕິດຕັ້ງ

ກະລຸນາອີງໃສ່: http://www.meanwell.com/manual.html

ເອກະສານ / ຊັບພະຍາກອນ

MEAN WELL NPB-450 Series 450W High Reliable Ultra Wide Output Range Intelligent Battery Charger [pdf] ຄູ່ມືການສອນ
NPB-450 Series, 450W High Reliable Ultra Wide Output Range Intelligent Battery Charger, NPB-450 Series 450W High Reliable Ultra Wide Output Range Intelligent Battery Charger

ເອກະສານ

ອອກຄໍາເຫັນເປັນ

ທີ່ຢູ່ອີເມວຂອງທ່ານຈະບໍ່ໄດ້ຮັບການຈັດພີມມາ. ທົ່ງນາທີ່ກໍານົດໄວ້ແມ່ນຫມາຍ *