ໂລໂກ້ Honeywell

H-Class - logo

HD Peel & Present Option

Honeywell OPT78-2627 H-Class Powered Internal Rewind Option - detamexຖືກຕ້ອງໂດຍລູກຄ້າຂອງພວກເຮົາ.

Honeywell OPT78-2613-04 H-Class Thermal Transfer Option

ໃນໄລຍະview

This document describes the contents, installation, and use of the Heavy Duty Peel and Present option for the H-Class printer. After verifying the contents of the kit and the tools needed, follow the steps below to install and begin using the option. A maintenance procedure is also included, so keep this documentation for future reference.

ການ​ເຕືອນ​ໄພ ຂໍ້ຄວນລະວັງ
For your safety and to avoid equipment damage, always turn ‘Off’ power and unplug the printer’s power cord before beginning this installation and when performing service.

Contents of the Heavy Duty Peel and Present Option

ຊຸດ​ນີ້​ປະ​ກອບ​ດ້ວຍ​ລາຍ​ການ​ດັ່ງ​ຕໍ່​ໄປ​ນີ້​:
• Heavy Duty Peel and Present Assembly

Honeywell H-4310 H-Class HD Peel and Present Option - Heavy Duty Peel and Presentເຄື່ອງມືທີ່ຕ້ອງການ
ເພື່ອຕິດຕັ້ງຕົວເລືອກນີ້, ທ່ານຈະຕ້ອງມີ screwdriver ມາດຕະຖານ.

ຂັ້ນຕອນທີ 1: ການກະກຽມເຄື່ອງພິມ

A) ປິດ 'ປິດ' ໄດ້ Power Switch ແລະຖອດສາຍໄຟອອກຈາກເຄື່ອງ ເຄື່ອງຮັບ AC.

Honeywell H-4310 H-Class HD Peel and Present Option - Preparing the Printer

B) ກົດລົງທີ່ ຈັບ, ຫຼັງຈາກນັ້ນ, ດຶງໄປຂ້າງຫນ້າເພື່ອເອົາອອກ ປະຕູ.

Honeywell H-4310 H-Class HD Peel and Present Option - DoorC) ຍົກ ການປົກຫຸ້ມຂອງການເຂົ້າເຖິງ ແລະເອົາສື່ຂອງເຈົ້າອອກຈາກເຄື່ອງພິມ.

Honeywell H-4310 H-Class HD Peel and Present Option - Access Cover

D) ດຶງອອກຈາກ ໂປ້ໂປ້ ແລະ Tear Plate. (Alternately, if equipped with an Arc Plate, Present Sensor, or Cutter, remove that device.)

Step 2: Installing the Heavy Duty Peel and Present Assembly

A) ກົດປຸ່ມ Latch ແລະເປີດ Peel and Present ສະພາແຫ່ງ.

Honeywell H-4310 H-Class HD Peel and Present Option - Present Assembly

B) ລະມັດລະວັງກົດ Peel and Present Assembly ເຂົ້າໄປໃນ Front Plate Connector.

Honeywell H-4310 H-Class HD Peel and Present Option - Peel and Present

C) ເຄັ່ງຄັດຂື້ນ ສະກູ ເພື່ອຄວາມປອດໄພ Peel and Present Assembly ກັບເຄື່ອງພິມ.

ຂັ້ນຕອນທີ 3: ການນໍາໃຊ້ທາງເລືອກ
ໃນລະຫວ່າງການປະຕິບັດການ, ປ້າຍຊື່ຈະຖືກປອກເປືອກອອກຈາກວັດສະດຸຮອງແລະແຈກຢາຍ "ຕາມຄວາມຕ້ອງການ" - ນັ້ນແມ່ນ, ການພິມຕໍ່ມາຈະເກີດຂື້ນພຽງແຕ່ຫຼັງຈາກປ້າຍທີ່ພິມອອກກ່ອນຫນ້ານີ້ໄດ້ຖືກໂຍກຍ້າຍອອກຈາກເຄື່ອງພິມ. ຕາມການເຕືອນ, “Remove LABEL” ຈະສະແດງຂຶ້ນເພື່ອເຕືອນທ່ານເມື່ອປ້າຍກຳກັບລໍຖ້າການລຶບອອກ.

ເລີ່ມ​ຕົ້ນ​ການ​ນໍາ​ໃຊ້​ທາງ​ເລືອກ​ດັ່ງ​ຕໍ່​ໄປ​ນີ້​:

A) Load ສື່ມວນຊົນ (ເບິ່ງຄູ່ມືຜູ້ປະຕິບັດງານສໍາລັບລາຍລະອຽດ). ຂະຫຍາຍ 20 ນິ້ວ (50 ຊຕມ) ຂອງ ສື່ມວນຊົນ ຈາກເຄື່ອງພິມ.

Honeywell H-4310 H-Class HD Peel and Present Option - Media

B) ເອົາປ້າຍຊື່ອອກຈາກສ່ວນຂະຫຍາຍຂອງສື່ນີ້, ປ່ອຍໃຫ້ມີພຽງແຕ່ ວັດສະດຸຮອງ. ສ້າງຂອບຊັ້ນນໍາຂອງເລື່ອງນີ້ BackingMaterial.
C)
ເສັ້ນທາງ ເອກະສານ ສຳ ຮອງ ພາຍ​ໃຕ້​ການ ຊ່ວຍເຫຼືອ Roller ແລະ Internal Rewinder.

Honeywell H-4310 H-Class HD Peel and Present Option - Backing

D) ຫໍ່ ເອກະສານ ສຳ ຮອງ ໃນທິດທາງ counterclockwise ປະມານ Rewinder Hub and insert the creased leading edge into one of its Slots. Insert the ເຂັມຂັດສື່ (Item 6) into the Slot over the creased leading edge of the ການສະ ໜັບ ສະ ໜູນ Material and around the Rewinder Hub.

Honeywell H-4310 H-Class HD Peel and Present Option - Backing Material

E) ປິດ Peel and Present Assembly. Close the Access Cover, plug the power cord into the AC Receptacle, and turn ‘On’ the Power Switch.

Honeywell H-4310 H-Class HD Peel and Present Option - Peel and Present Assembly

F) ຮັບປະກັນວ່າ ກຽມພ້ອມ is displayed on the Front Panel then press the ລະຫັດອາຫານ ແລະດໍາເນີນການຕາມການສັງເກດຂອງທ່ານ:

  • If REMOVE LABEL is displayed on the Front Panel, this completes the installation; or,
  • If REMOVE LABEL is not displayed on the Front Panel, proceed to step 4: “Configuring the Printer.”

Honeywell H-4310 H-Class HD Peel and Present Option - Front Panel

ຫມາຍເຫດ:

  1. ການເຮັດວຽກຂອງ Present Sensor ໃນຕົວເລືອກນີ້ຍັງສາມາດຖືກຄວບຄຸມໂດຍຄໍາສັ່ງຊອບແວໂຮດ, ດັ່ງນັ້ນໃຫ້ແນ່ໃຈວ່າໂຄງການປ້າຍຊື່ຂອງທ່ານຖືກຕັ້ງຄ່າຢ່າງຖືກຕ້ອງສໍາລັບການນໍາໃຊ້ໃນເວລາທີ່ສົ່ງຮູບແບບປ້າຍຊື່ໄປຫາເຄື່ອງພິມ.
  2. ຖ້າຕົວເລືອກນີ້ຖືກເອົາອອກດ້ວຍການໃຊ້ພະລັງງານ, ເຄື່ອງພິມຈະປະຕິບັດຄືກັບວ່າປ້າຍຊື່ລໍຖ້າການໂຍກຍ້າຍ; ເພື່ອຟື້ນຟູການເຮັດວຽກປົກກະຕິ, ວົງຈອນພະລັງງານກັບເຄື່ອງພິມ.

ຂັ້ນຕອນທີ 4: ຕັ້ງຄ່າເຄື່ອງພິມ

While the Heavy Duty Peel and Present option is a plug-and-play device, this step may be necessary if the printer’s default configuration has been changed. Follow the steps below to configure the printer:

ຫມາຍ​ເຫດ​: ໃນຂັ້ນຕອນຕໍ່ໄປນີ້, ໃຫ້ປຶກສາກັບຄູ່ມືຂອງຜູ້ປະຕິບັດງານສໍາລັບຄໍາແນະນໍາດ້ານຫນ້າຢ່າງລະອຽດ.

A) ກົດປຸ່ມ MENU Button on the printer’s front panel.
B) ການນໍາໃຊ້ ລົງ Button, scroll to ຕົວເລືອກເຄື່ອງພິມ then press the Right Button.
C) ການນໍາໃຊ້ ລົງ Button, scroll to ເຊັນເຊີປະຈຸບັນ ຈາກນັ້ນກົດປຸ່ມ ປ້ອນລະຫັດ.
D) ການນໍາໃຊ້ ລົງ Button, scroll to MODE ຈາກນັ້ນກົດປຸ່ມ ປ້ອນລະຫັດ.
E) ການນໍາໃຊ້ ລົງ Button, scroll to AUTO ຈາກນັ້ນກົດປຸ່ມ ENTER ກຸນແຈ.
F) ກົດປຸ່ມ ອອກ Key then, at the ບັນ​ທຶກ​ການ​ປ່ຽນ​ແປງ? prompt, ເລືອກ YES ເພື່ອໃຫ້ ສຳ ເລັດການຕິດຕັ້ງ.
G) Turn the Power Switch 'ປິດ' ແລະ ‘On’ to reset the printer and complete the configuration.

ຫມາຍ​ເຫດ​: If the printer fails to separate the labels from the backing material, and the Internal Rewinder is not turning, it may need to be enabled. Using the procedure above as a guide, press the MENU Button, scroll to PRINTER OPTIONS, ຫຼັງຈາກນັ້ນໃຫ້ REWINDER, ແລະເລືອກເອົາ ອັດຕະໂນມັດ. Afterward, press the ອອກ key and save your changes when prompted.

Maintaining the Heavy Duty Peel & Present Assembly

To ensure trouble-free operation, the Heavy Duty Peel and Present Assembly should be cleaned after every 100,000 inches (254,000 cm) of media use. This interval depends on the label adhesive, where “gummy” adhesives may require more frequent cleaning. (To easily track label usage, go to SYSTEM SETTINGS → MEDIA COUNTERS in the printer’s menu system.)

Clean the assembly as follows:

  1. ປິດ 'ປິດ' ສະວິດໄຟ ແລະຖອດສາຍໄຟອອກຈາກບ່ອນຮັບ AC. ຍົກຝາປິດການເຂົ້າເຖິງ ແລະເອົາສື່ອອກຈາກເຄື່ອງພິມ.
  2. Remove the Peel & Present Assembly from the printer.
  3. ການນໍາໃຊ້ອາກາດບີບອັດຫຼືແປງອ່ອນ, ເຮັດຄວາມສະອາດ Sensors on the assembly.Honeywell H-4310 H-Class HD Peel and Present Option - Sensorsຫມາຍ​ເຫດ​: ສໍາລັບການເຮັດຄວາມສະອາດເງິນຝາກຫນັກ, ເຫຼົ້າ isopropyl ສາມາດນໍາໃຊ້ໄດ້ - ສະຫນອງໃຫ້ມັນຖືກນໍາໃຊ້ຢ່າງລະມັດລະວັງໂດຍໃຊ້ຜ້າຝ້າຍ, ແລະຫຼັງຈາກນັ້ນອະນຸຍາດໃຫ້ແຫ້ງກ່ອນທີ່ຈະເຊື່ອມຕໍ່ທາງເລືອກກັບເຄື່ອງພິມ.
  4. ກົດປຸ່ມ Latch to open the Peel and Present Assembly. Then remove the ຄ-ຄລິບ that secures the Upper Roller Shaft ການ Front Cover.Honeywell H-4310 H-Class HD Peel and Present Option - Front Cover
  5. Remove the Upper Roller Shaft and the associated Rollers.Honeywell H-4310 H-Class HD Peel and Present Option - Rollers
  6. ການນໍາໃຊ້ ຝ້າຍຝ້າຍ dampened with alcohol, wipe all roller ແລະ Upper Roller Shaft surface clean. Pay special attention to the ridges on the Rollers to ensure that they are clean.
    ຫມາຍ​ເຫດ​: For cleaning heavy deposits from the Rollers and Shafts in the following steps, WD-40 or another non-damaging adhesive remover can be substituted for isopropyl alcohol – provided this adhesive remover is carefully applied using a cotton swab.
  7. ເລື່ອນພາບ Rollers ກັບຄືນໄປບ່ອນໃສ່ Upper Roller Shaft, place the components into the Front Cover, and reinstall the C-Clip.
  8. Push ແລະ Lift ທັງສອງ Tabs ທີ່ຮັບປະກັນໄດ້ Lower Roller Assembly to the Front Cover (as shown) and then, while keeping it intact, carefully remove the entire Lower Roller Assembly.Honeywell H-4310 H-Class HD Peel and Present Option - Tabs
  9. Take note of the individual roller positions – they must be reinstalled in the same order – then, carefully remove the Rollers ຈາກ Lower Roller Shaft.Honeywell H-4310 H-Class HD Peel and Present Option - Lower Roller Shaf
  10. ການນໍາໃຊ້ ຝ້າຍຝ້າຍ dampened with alcohol, wipe all roller ແລະ Lower Roller Shaft surfaces clean. Pay special attention to the ridges on the Rollers to ensure that they are clean.
  11. ເລື່ອນພາບ Rollers, in their original order, onto the Lower Roller Shaft and reinstall them in the Front Cover, ຮັບປະກັນວ່າ Tabs are properly seated. Reinstall the Peel and Present Assembly onto the printer to complete the cleaning procedure.

ເອກະສານ / ຊັບພະຍາກອນ

Honeywell H-4310 H-Class HD Peel and Present Option [pdf] ຄໍາແນະນໍາ
H-4310, H-Class, HD Peel and Present Option, H-4310 H-Class HD Peel and Present Option

ອອກຄໍາເຫັນເປັນ

ທີ່ຢູ່ອີເມວຂອງທ່ານຈະບໍ່ໄດ້ຮັບການຈັດພີມມາ.