Willful ID205 Smartwatch
Willful ID205 Smartwatch
Thank you for purchasing our products. This manual addresses the safety guidelines, warranty, and operating instructions. Please review this manual thoroughly before operating your device.
What’s in the box
What’s in this document
This manual gets you started quickly with setting up your watch. Setup ensures that your watch can synchronize its data with the VeryFitPro app, where you can get detailed information on your stats, view historical trends, log sleep, and more. As soon as setup is complete, you’re ready to start moving. The remainder of the manual walks you through every function on your ID205.
Setting up Your Watch
Charging your watch
Please fully charge your watch before initial use.
- . Plug the charging cable into the USB port on your computer or a UL-certified USB wall charger.
- Place the watch in the charging cradle and push it in until you hear a click. The pins on the charging cradle must align with the gold contacts on the back of the watch. The percent charged appears on the screen.
When the watch shows that the battery is low, connect the watch to a USB charging adaptor or a port with 5V-500mA. If the watch is installed correctly, it will vibrate.
While the watch charges, press the left/right button to check the battery level.
Remove the watch from the power supply once fully
charged.
- USB charger requirement: DC USB port (5V-500mA)
- Charging time: 2-3 hours
Disassembling / Assembling Your Watch
Disassembly
- To remove the wristbands, turn over the watch and find the quick-release lever.
- While pressing the quick-release lever inward, gently pull the wristband away from the watch to release it.
- Repeat on the other side.
Assembly
- To reattach the wristbands, slide the pin (the side opposite the quick-release lever) into the notch on the watch. Attach the wristband with the clasp to the top of the watch.
- While pressing the quick-release lever inward, slide the other end of the wristband into place.
- When both ends of the pin are inserted, release the quick-release lever.
Wearing Your Watch
All-day wear and exercise
For all-day wear when you’re not exercising, wear the device on your wrist horizontally, a finger’s width below your wrist bone and lying flat, the same way you would put on a watch.
For optimized heart rate tracking, keep these tips in mind:
- Experiment with wearing the watch higher on your wrist during exercise. Because the blood flow in your arm increases the farther up you go, moving the watch up a couple of inches can improve the heart rate signal. Also, many exercises such as bike riding or weight lifting require you to bend your wrist frequently, which is more likely to interfere with the heart rate signal if the watch is lower on your wrist.
- Do not wear your watch too tight. A tight band restricts blood flow, potentially affecting the heart rate signal. This being said, the watch should also be slightly tighter (snug but not constricting) during exercise than during all-day wear.
Using Your Watch
App Installation
Use the watch with our customized VeryFitPro app. You can download VeryFitPro from Apple Store/Google Play or scan the QR codes below to download.
QR Code For Android
QR Code For iOS
Notes:
- The VeryFitPro app is only compatible with smartphones, not tablets or PCs.
- Smartphone operating system should be iOS 8.0 / Android 4.4 or higher; Bluetooth version should be 4.0 or higher.
Smart Phone System Requirements
- iOS 8.0 & higher
- Android 4.4 & higher
- Bluetooth 4.0 & higher
App Interfaces
Pairing the Watch with Your Phone
Please pair the watch with your phone in the VeryFitPro app, NOT in the Bluetooth settings of your phone.
- Enable the Bluetooth of your smartphone.
- Open the VeryFitPro app on your smartphone and go to the “Device” page, tap “Bind Device”, then your smartphone starts searching devices.
- In the list of found devices that appear on your smartphone, tap on “ID205” to connect the watch to your smartphone. (If your phone failed to find ID205, please search the watch on your smartphone again.)
Notes:
- Once the watch is connected to your app, the watch will automatically search and reconnect itself if the connection is lost or when Bluetooth is restarted after manual disconnection.
- If the watch is unbound from the app, the information or the watch will be reset, and the information on the app will be cleared. Please do not unbind the connection unless there is an issue that will require a reset.
- The watch can only pair with one smartphone at a time. When pairing, please ensure the watch and your smartphone is within 0.5 meters distance.
Getting to Know Your Watch
Button Functions
Press and hold the left button to enter the sports mode. (you can define a specific sports mode in the function list of the watch 
“Setting” “Long press”.)
- Press the right button to return to the previous interface
- Press and hold the right button to turn on the watch.
Watch Interfaces
This is a touch screen; swipe the screen to go to different interfaces, and tap to enter the function.
The home screen is the clock. On the clock:
- Swipe down to see notifications.
- Swipe up to see your daily stats.
- Swipe left to see the function list.
- Swipe right to see the status bar.
Notes: When the battery level is less than 15%, the watch enters battery save mode, at which you cannot operate the watch. Please charge the watch to operate it again. After the watch is bound to the app, the home screen will display the time and date as shown in fig. 1.
You can customize the home screen by following the steps below:
- Tap and hold the home screen.
- Swipe down to choose one and tap to confirm.
Home Screen (default)
Tap the screen to switch between steps, distance, and calories. Contents displayed may be different according to the home screen you choose.
Wake a Dimmed Screen
To conserve power, the watch has a standby mode in which the screen turns off. To wake the screen, turn your wrist towards you or press the left/right button.
Function Introduction
Tracks your exercise data in up to 14 sports modes. Choose the modes that you want to display on the watch in the app.
Tracks your real-time heart rate automatically and continuously.
Guides your breathing for a relaxation.
Set alarms in the app to have the watch vibrates to wake you up, take pills, and more.
Control the music playing of your smartphone.
Timing and countdown.
Some basic settings of the watch.
Your recent sports record.
1. Tracking Sports
The watch tracks your exercise data in up to 14 sports modes. You can set up to 8 different sports modes from among 14 sports modes in the app to display on the watch scteen (“Device” page “More” “Activity display”).
During sports
- Swipe the screen left/right to flip through exercise data.
- Press the right key to pause/resume the sport.
2. Monitoring Heart Rate
The watch tracks your real-time heart rate automatically and continuously. You can also view your detailed heart rate data on the watch screen or in the app.
3. Relaxing
Tap 
to start the relaxing Press the right button to end the relaxing |Tap 
to confirm
4. Setting Alarms
- Go to the “Device” page in the app and tap “Alarm Alert”.
- Tap “+” to add an alarm.
- Tap the alarm, then set the alarm type, repeat type and time.
- Tap “” to save you settings.
You can tap the alarm you set on the watch screen to enable/disable the alarm.
5. Controlling Phone Music
- Go to the “Device” page in the app and tap “Music Control”.
- Enable the function and tap ” ” to save your settings
- Tap “Music Controller” on the watch screen to enter the function and control the music playing on your phone.
Note:
You can only control the music player that’s running on your smartphone.
6. Tracking Sleep
The watch automatically tracks your sleep duration (Deep Sleep, Light Sleep, and Wake-sleep) and consistency with a comprehensive analysis of sleep quality data so you can see your sleep trends and improve your routine.
You can check your detailed sleep data in the app.
7. More Functions
7.1 Call Notification
When there is an incoming call, the watch vibrates to alert you, and the screen displays the caller ID.
Tap 
on the watch screen to reject the call.
7.2 Message Notification
When messages (SMS, Facebook, WhatsApp, Twitter, Instagram, Facebook Messenger, LinkedIn, Email, Mail, Calendar, and more) come in, the watch vibrates to alert you, and the screen displays the message content.
7.3 Women’s Health Tracking
The watch reminds you of your important days like
menstrual period and safe period at the time you set
when you enable the function in the app (“Device” page “Health care”)
7.4 Sedentary Reminder
The watch vibrates to remind you to get up and move around when you have been sitting too long (“Device” page “Sedentary Alert”, enable the Sedentary Alert function and set the remind interval.)
7.5 Find Phone
The watch vibrates to remind you to get up and move around when you have been sitting too long (“Device” page “Sedentary Alert”), enable the Sedentary Alert function and set the remind interval.)
Basic Specifications
Model No.: ID205
Sync: Bluetooth 4.0
Screen: 1.3″ TFT LCD
Battery Capacity: 210mAh
Working Voltage: 3.8V
Working Temperature: -10℃ to 40℃
Weight: 1.37oz (39g)
Waterproof Rating: 5ATM
Working Time: 10+ days
Warranty
We strive to build our products with the highest attention to detail and craftsmanship. However, sometimes there are occurrences of a defect, so we are happy to offer a ONE-year hassle-free warranty on all our devices as we continue to make amazing products. Please contact us if you have any questions about our devices.
Important Safety Instructions
The device contains electrical equipment that may cause injury if not used properly. For example, prolonged contact may contribute to skin allergies for some users. To reduce irritation, please read the safety guidelines on the following pages to ensure proper use and care.
- Do not expose your device to liquid, moisture, humidity or rain while charging; do not charge your device when it is wet, as this may result in electrical shock and injury.
- Keep your device clean and dry. Do not use abrasive cleaners to clean your device.
- Consult your doctor before use if you have any preexisting conditions that might be affected by using this device.
- Do not wear it too tight. If your device feels hot or warm, or if it causes any skin irritation or other discomforts, please discontinue using your device and consult your doctor.
- Do not expose your watch to extremely high or low temperatures.
- Do not leave your watch near open flames such as cooking stoves, candles, or fireplaces.
- This product is NOT a toy – never allow children or pets to play with this product. Always store the product out of the reach of children. The devices themselves or the many small parts they contain may cause choking if ingested.
- Never try to abuse, crush, open, repair or disassemble this device. Doing so will void the warranty and can result in a safety hazard.
- If any parts of your product require replacement for any reason, including normal wear and tear or breakage, please contact us.
- Do not use your device in a sauna or steam room.
- Dispose of this device, the device’s battery and its package in accordance with local regulations.
- Do not check any notifications, GPS, or any information on your device’s display while driving or in other situations where distractions could cause injury or hazard. Always be aware of your surroundings while exercising.
Battery Warnings
A lithium-ion battery is used in this device. If these guidelines are not followed, batteries may experience a shortened life span or may cause fire, chemical burn, electrolyte leakage, and/or injury.
- Do NOT disassemble, modify, manufacturer, puncture or damage the device or batteries.
- Do NOT remove or attempt to remove the non user replaceable battery.
- Do NOT expose the device or batteries to fire explosion, or other hazards.
Health Warnings
- If you have a pacemaker or other internal electronic device, consult your physician before using a heart rate monitor.
- The optical wrist heart rate monitor emits green light and flashes occasionally. Consult your physician if you have epilepsy or are sensitive to flashing light.
- Always consult your physician before beginning or modifying any exercise program.
- The device, accessories, heart rate monitor, and related data are intended to be used only for recreational purposes and not for medical purposes and are not intended to diagnose, monitor, treat, cure, or prevent any disease or condition.
- The heart rate readings are for reference only, and no responsibility is accepted for the consequences of any erroneous readings.
- While the optical wrist heart rate monitor technology typically provides the best estimate of a user’s heart rate, there are inherent limitations with the technology that may cause some of the heart rate readings to be
inaccurate under certain circumstances, including the user’s physical characteristics, fit of the device, and type and intensity of activity. - The smart watch relies on sensors that track your movements and other metrics. The data and information provided by these devices are intended to be a close estimation of your activity and metrics tracked, but may not be completely accurate, including step, sleep, distance, heart rate, and calorie data.
- If you have eczema, allergies or asthma, you may be more likely to experience skin irritation or allergies from a wearable device.
- Whether you have the conditions above or not if you start to experience any discomfort or skin irritation on your wrist, remove your device. If symptoms persist longer than 2-3 days of not using your device, contact your doctor.
If you sweat for more than two hours while wearing your watch, be sure to clean and dry your band and your wrist to avoid skin irritation. - Prolonged rubbing and pressure may irritate the skin, so give your wrist a break by removing the band for an hour after extended wear.
Maintenance
- Regularly clean your wrist and the smart watch especially after sweating during exercise or being exposed to substances such as soap or detergent which may adhere to the internal side of the watch.
- Do NOT wash the watch with household cleanser.
Please use soapless detergent, rinse thoroughly and wipe with a soft towel or napkin. - While the watch is water resistant, wearing a wet band is not good for your skin.
- If your bands get wet—for example after sweating or showering—clean and dry them thoroughly before putting them back on your wrist.
- Be sure your skin is dry before you put your bands back on.
- Do not bring your device into contact with any sharp objects, as this could cause scratches and other damage.
- For light-colored arm bands, minimize direct contact with dark-colored clothing, as color transfer can occur.
DOWNLOAD RESOURCES
- ID205 Smartwatch Instruction Manual – Optimized PDF
- ID205 Smartwatch Instruction Manual – Original PDF
FAQ’S
The computer may charge the watch at a slower rate. If you are in a hurry, use the USB charger.
It takes about 2 hours to fully charge the watch.
When you connect your watch to a USB port on your computer, it will vibrate and show that it’s charging. When it’s fully charged, it will stop vibrating. If you are using a USB charger, the screen will flash “100%” when it’s fully charged.
Your watch will vibrate and show that it’s charging when you connect it to a USB port on your computer or a UL-certified USB wall charger. If you are using a USB charger, the screen will flash “100%” when it’s fully charged.
The battery won’t be damaged if left on the charging cradle for more than 24 hours. However, we recommend that you remove your watch from the cradle after 24 hours to conserve battery power.
No, only use UL-certified USB wall chargers or computers to charge your ID205. Using an iPhone or iPad adapter may damage your device and void its warranty.
Only use the cable provided with your device or an Apple-certified cable to charge your device. Using other cables may damage your device and void its warranty.
Only use UL-certified wall chargers to charge your ID205. Using other chargers may damage your device and void its warranty.
You can get text, call, calendar, email and smartphone app notifications, also support messages reading on this watch. 【Waterproof Fitness Tracker with Heart Rate Monitor 】- Automatically track your all-day steps,calories,distance,24/7 heart rate, sleep quality.
Yes. Many fitness trackers can be used independently from a smartphone. Commonly, smartphones and mobile devices have helpful functions for monitoring exercises and configuring settings. For most exercise watches, the software used to monitor steps, speed, and heart rate information is generally self-contained.
If you are an outdoor runner, cyclist, or swimmer, and you want to track your workouts as accurately as possible, you should purchase a device with a built-in GPS sensor. Garmin has a ton of GPS running watches available with built-in GPS, and the Fitbit Versa 3 is pretty great too.
If you prefer to exercise in the pool, don’t worry because the ID205S sports IP68-rated water resistance.
References
- User Manualmanual.tools
Got it, and it’s a great watch! Just someone an idea why my vibration function doesn’t work when I get a message? Call not coming in either …
Heb hem, en is een super watch! Alleen iemand een idee waarom mijn trilfunctie het niet doet als ik een berichtje krijg? Oproep komt ook niet binnen…
Heb hem, en is een super watch! Alleen iemand een idee waarom mijn trilfunctie het niet doet als ik een berichtje krijg? Oproep komt ook niet binnen...
Why is my ID205 smartwatch not vibrating or receiving call and message notifications?
If your ID205 smartwatch is not vibrating or showing notifications for calls and messages, please check the following settings in the VeryFitPro app and on your phone:
If these steps do not work, try unbinding the watch from the app and re-pairing it.
Note: The user's original comment was in Dutch: "Heb hem, en is een super watch! Alleen iemand een idee waarom mijn trilfunctie het niet doet als ik een berichtje krijg? Oproep komt ook niet binnen..."
Read the full Q&A page
There is nothing in the manual to explain how to use the status bar.
I’m not sure how to program this
I'm not sure how to program this
How do I use the status bar and program the Willful ID205 smartwatch?
To access and use the Status Bar on your Willful ID205 smartwatch, follow these steps:
Regarding programming or setting up the device, most configuration is done through the VeryFitPro app rather than on the watch itself:
If you need to change the watch face (the home screen), tap and hold the current clock face, then swipe down to select a new design and tap to confirm.
Note: If the watch is unresponsive, ensure it has more than 15% battery, as it enters a restricted battery-saving mode below that level.
Read the full Q&A page
What does it mean when 1000 lights up and it vibrates ?? looks like you have reached a goal, but which one ???
Was bedeutet es wenn 1000 aufleuchtet und es vibriert??sieht aus,als ob man ein Ziel erreicht hätte,aber welches???
Was bedeutet es wenn 1000 aufleuchtet und es vibriert??sieht aus,als ob man ein Ziel erreicht hätte,aber welches???
What does it mean when the watch vibrates and displays the number 1000?
When your Willful ID205 smartwatch vibrates and displays a number like 1000 (or more commonly 10,000), it indicates that you have reached a daily activity goal. Based on the manual and the VeryFitPro app functionality, this is most likely your Step Goal.
By default, many fitness trackers set a daily target. You can verify or change this goal by following these steps in the app:
The vibration and on-screen animation are designed to celebrate your achievement for the day.
Read the full Q&A page
My bluthout doesn’t recognize the watch. I tried rebooting, updating, verifying versions, reinstalling but nothing. Does it recognize all the other devices but not my watch, what should I do?
Il mio bluthout non riconosce l’orologio. Ho provato a riavviare, aggiornare, verificare le versioni, reinstallare ma nulla. Riconosce tutti gli altri dispositivi ma non il mio orologio come devo fare?
Il mio bluthout non riconosce l'orologio. Ho provato a riavviare, aggiornare, verificare le versioni, reinstallare ma nulla. Riconosce tutti gli altri dispositivi ma non il mio orologio come devo fare?
Why is my phone's Bluetooth not recognizing the Willful ID205 smartwatch even after rebooting and reinstalling the app?
The most common reason for this issue is attempting to pair the watch directly through your phone's Bluetooth settings. According to the Willful ID205 Instruction Manual, you must pair the watch through the VeryFitPro app specifically.
Please follow these steps to resolve the connection issue:
If the device still does not appear in the app, try toggling your phone's Bluetooth off and back on, and ensure that Location Services (GPS) are enabled for the VeryFitPro app in your phone's privacy settings, as this is often required for Bluetooth scanning on Android devices.
Read the full Q&A page
What does it mean when 10.00 appears on the screen and it vibrates?
Que significado tiene cuando me aparece en la pantalla 10.00y me vibra?
Que significado tiene cuando me aparece en la pantalla 10.00y me vibra?
What does it mean when the screen displays 10.00 and the watch vibrates?
Based on the manual for the Willful ID205, there are two primary reasons your watch might vibrate and show a specific number or icon:
To verify what this notification is, open the VeryFitPro app on your smartphone, go to the Device page, and check your Alarm Alert settings or your Activity goals. If the vibration happens while you are walking, it is almost certainly a goal completion notification.
Read the full Q&A page
Can I switch the display completely dark at night?
Kann ich die Anzeige nachts ganz dunkelschalten?
Kann ich die Anzeige nachts ganz dunkelschalten?
How can I turn off the display or make it dark at night?
To keep the display dark at night on your Willful ID205, you should disable the "Sense Wrist" (Wake Gesture) feature and ensure notifications are silenced. While the watch does not have a dedicated "theatre mode" button, you can manage this through the VeryFitPro app:
To wake the screen manually when these features are off, simply press the Right Button.
Read the full Q&A page
Does anyone know how to contact the brand for the warranty? It has stopped working for me and is two months old
Sabe alguien cómo contactar con la marca para la garantía? Me ha dejado de funcionar y tiene dos meses
Sabe alguien cómo contactar con la marca para la garantía? Me ha dejado de funcionar y tiene dos meses
How can I contact the brand for a warranty claim if my smartwatch stopped working after two months?
The Willful ID205 smartwatch typically comes with a one-year hassle-free warranty. To initiate a warranty claim or seek support for a device that has stopped working, you can try the following contact methods based on the manufacturer details for the ID205 series:
itserver@idoocn.comorchunling509223@gmail.com.+86 136 4094 6524.When contacting them, be sure to provide your order number, the date of purchase, and a description of the issue to expedite the process.
Read the full Q&A page
I would like to know if I can change the screen that shows the steps and remove the bar at the bottom, I just want the steps to be larger so I can see when I am actively exercising. I don’t need the graph. Thank you!
How can I change the screen display to make the step count larger and remove the graph?
On the Willful ID205, you can customize the home screen to find a layout that better suits your visibility needs, though specific UI elements like graphs within a particular face cannot be individually toggled off.
To change your watch face for better visibility:
Regarding the "bar at the bottom" or graph: these are usually hard-coded into specific watch face designs. If the current face includes a graph you find distracting, your best option is to switch to a different watch face that uses a text-only layout for activity tracking.
Read the full Q&A page
This watch is impossible to figure out how to change the time during central daylight savings time.
How do I change the time on my Willful ID205 smartwatch for Daylight Savings Time?
The time on your Willful ID205 smartwatch cannot be set manually on the watch itself. It is designed to automatically synchronize with the time and date on your smartphone once it is paired via the VeryFitPro app.
To update the time for Daylight Savings, follow these steps:
If your phone has already updated to Central Daylight Savings Time but the watch has not, try unbinding and rebinding the device in the app's settings to reset the connection.
Read the full Q&A page
Sync with the flu caller installed on your phone
Faire une synchro avec l appeler grippe installé sur votre téléphone
Faire une synchro avec l appeler grippe installé sur votre téléphone
How do I change the time on my Willful ID205 smartwatch for Daylight Savings Time?
Sync with the flu caller installed on your phone
Faire une synchro avec l appeler grippe installé sur votre téléphone
did anyone reply to your answer? Cant get blietooth to come on the watch
I agree with Kevin. Everything is in the User Manuel except how to change the time! Does anyone know?
How do I change the time on the Willful ID205 Smartwatch?
The time on the Willful ID205 smartwatch cannot be set manually on the device itself. Instead, the watch automatically synchronizes its time and date from your smartphone once it is paired via the VeryFitPro app.
To set or correct the time, follow these steps:
If the time becomes inaccurate over time, simply open the app and perform a manual sync by pulling down on the app's home screen while the watch is connected via Bluetooth.
Read the full Q&A page
You have to sync your phone to the watch through the Very Fit Pro app
How do I change the time on the Willful ID205 Smartwatch?
You have to sync your phone to the watch through the Very Fit Pro app
It’s automatic, just sync very fit pro with watch on those days.
How do I change the time on the Willful ID205 Smartwatch?
It’s automatic, just sync very fit pro with watch on those days.
Hello, a favor, my watch went off and I could not turn it on again, what should I do, thank you very much
Buenas, un favor mi reloj se apago y no lo he podido volver a encender, que debo hacer, muchas gracias
Buenas, un favor mi reloj se apago y no lo he podido volver a encender, que debo hacer, muchas gracias
How do I turn on my Willful ID205 smartwatch if it has turned off and won't restart?
To turn on your Willful ID205 smartwatch, press and hold the right button. If the watch does not respond, please try the following troubleshooting steps:
Read the full Q&A page
My watch is 6 mins behind. I have read the operation instructions twice and I am now seeing how to change the time.
How do I change or sync the time on my Willful ID205 smartwatch?
On the Willful ID205 smartwatch, you cannot manually change the time directly on the watch itself. The time is automatically synchronized from your smartphone once the device is paired via the VeryFitPro app.
To correct the time, please follow these steps:
If the watch is already paired but the time is incorrect, try toggling your phone's Bluetooth off and on, then reopen the app to force a resync. According to the manual, once the watch is bound to the app, the home screen will automatically display the correct time and date from your phone.
Read the full Q&A page
can you set a reminder when you do not have 250 steps in an hour. in other words can you get an alert with about 10 minutes left when you do not have 250 steps
Can I set a reminder to alert me if I haven't reached 250 steps within an hour, specifically with 10 minutes remaining in that hour?
The Willful ID205 (using the VeryFitPro app) does not currently support a specific "250 steps per hour" reminder with a 10-minute warning. However, it does feature a Sedentary Reminder (Sedentary Alert) that can help you stay active.
To enable the Sedentary Reminder:
When enabled, the watch will vibrate to remind you to get up and move if you have been inactive for the duration of your set interval. While it does not track a specific step count for that hour or provide a 10-minute warning, it is the primary tool available for preventing prolonged sitting.
Read the full Q&A page
I’m having the same problem. How do you set the time?
How do I set the time on my Willful ID205 smartwatch?
To set the time on your Willful ID205 smartwatch, you must pair it with your smartphone using the VeryFitPro app. The watch does not have a manual time-setting menu; it automatically synchronizes its time and date from your phone once a connection is established.
Follow these steps to sync the time:
Note: Do not try to pair the watch directly through your phone's Bluetooth settings; the connection must be made within the VeryFitPro app for the data and time to sync correctly.
Read the full Q&A page
How do you set watch to military time?
How do you set the watch to military time?
To change your Willful ID205 to military (24-hour) time, you must use the VeryFitPro app on your smartphone, as this setting cannot be changed directly on the watch itself. Follow these steps:
If you do not see the option under System Settings, check the Device page and look for "More" or "Device Settings" to find the time format toggle.
Read the full Q&A page
How to change the length of the steps ?? Where to look for it ??
Jak zmienić długość kroków?? W którym miejscu tego szukać??
Jak zmienić długość kroków?? W którym miejscu tego szukać??
How do I change the step length on the Willful ID205 smartwatch and where is this setting located?
To change the step length (stride length) for your Willful ID205, you must use the VeryFitPro app on your smartphone, as this setting is not available directly on the watch face.
Follow these steps to find the setting:
Note: If you cannot find a manual entry for step length, the app often calculates it automatically based on the Height you have entered in your profile. Ensure your height is set correctly to improve step and distance accuracy.
Wersja polska: Ustawienie to znajduje się w aplikacji VeryFitPro w sekcji Użytkownik (User) -> Informacje osobiste. Długość kroku jest zazwyczaj obliczana automatycznie na podstawie Twojego wzrostu, więc upewnij się, że podany wzrost jest prawidłowy.
分析结果如下：
Read the full Q&A page
I have a ID205L smart watch, and a Samsung S9. Everything seems to be working fine except it doesn’t record my sleep, and I have to keep refreshing the app so the time on my watch syncs. How do I get the sleep to record?
How do I fix sleep tracking and time synchronization issues on my ID205L smartwatch?
To resolve sleep tracking and time synchronization issues on your ID205L, please follow these steps:
Read the full Q&A page
To change the time, you must re-sync your watch with your phone. It is your phone that determines the time on the watch. Not the watch itself.
my ID205L continuously offers me a screen with a red exclamation point inside a circle and under the number -05.
Moreover, it does not let me use the sports track as as soon as I start it after a few seconds the aforementioned signal appears and it stops.
Thanks for your help
il mio ID205L mi propone continuamente una schermata con un punto esclamativo rosso dentro un cerchio e sotto il numero -05.
Oltretutto non mi fa usare il track sportivo in quanto appena lo faccio partire dopo pochi secondi mi compare il suddetto segnale e si ferma.
grazie per l’aiuto
Moreover, it does not let me use the sports track as as soon as I start it after a few seconds the aforementioned signal appears and it stops.
Thanks for your help</em>
il mio ID205L mi propone continuamente una schermata con un punto esclamativo rosso dentro un cerchio e sotto il numero -05.
Oltretutto non mi fa usare il track sportivo in quanto appena lo faccio partire dopo pochi secondi mi compare il suddetto segnale e si ferma.
grazie per l'aiuto
How do I fix error code -05 with a red exclamation point on my ID205L smartwatch?
The red exclamation point with error code -05 on the ID205L (VeryFitPro-based) smartwatch typically indicates a data synchronization or firmware initialization error, often occurring when the watch's memory is full or the sports mode fails to start correctly.
To resolve this, please try the following steps:
If the red exclamation point remains after a full charge and re-pairing, the device may have a hardware sensor fault requiring replacement under its one-year warranty.
Note: The manual mentions that unbinding the device will reset the watch information, which is often necessary to clear persistent error codes.
分析
Read the full Q&A page
what does the screen with a red exclamation mark and under the number -05 mean?
thank you
cosa significa la schermata con un punto esclamativo rosso e sotto il numero -05?
grazie
thank you</em>
cosa significa la schermata con un punto esclamativo rosso e sotto il numero -05?
grazie
What does a red exclamation mark with the code -05 mean on the Willful ID205 smartwatch?
On the Willful ID205 (and similar models using the VeryFitPro platform), a red exclamation mark accompanied by a numeric code typically indicates a firmware or synchronization error.
The code -05 specifically often points to a failed firmware update or a Bluetooth communication timeout. To resolve this, please try the following steps:
If the battery is below 15%, the watch may enter a restricted mode; ensure the device is charged to at least 50% before attempting a firmware fix.
Read the full Q&A page
Sleep data is supposed to be automatic, but when I go to bed (two days), I sleep, but I don’t get any data. why. What should I do.
睡眠データは自動でするとなっていますが、寝るとき（二日）につけて寝ていますが、データを取りません。なぜですか。どうしたらいいですか。
睡眠データは自動でするとなっていますが、寝るとき（二日）につけて寝ていますが、データを取りません。なぜですか。どうしたらいいですか。
Why is my Willful ID205 smartwatch not recording sleep data automatically, and how can I fix it?
The Willful ID205 (using the VeryFitPro app) tracks sleep automatically, but it requires specific conditions to record data correctly. Please try the following steps to resolve the issue:
If these steps do not work, try restarting your smartphone's Bluetooth or unbinding and re-pairing the watch within the app (note: unbinding may clear unsynced data).
Read the full Q&A page
I can not get my watch to pair with my phone again after disconnecting it
How do I re-pair my Willful ID205 smartwatch with my phone after it has been disconnected?
To re-pair your Willful ID205 smartwatch, please follow these steps to ensure a clean connection:
Note: If the watch was previously "unbound" from the app, it may have reset its data. If you continue to have trouble, try restarting both your phone's Bluetooth and the watch (by long-pressing the right button to turn it off/on) before attempting to bind again.
System Requirements: iOS 8.0 / Android 4.4 or higher, and Bluetooth 4.0 or higher.
Uncertainty Disclosure: While the manual states the watch should automatically reconnect after manual disconnection, persistent pairing issues often require "forgetting" the device in system settings before re-binding in the app.
Read the full Q&A page
The battery on my 205l ran right down when recharged unable to retain home screen and swipe, watch keeps flicking between functions and runs down battery within 24 hours, tried rebooting in app without any success.
How can I fix my ID205L smartwatch if the battery drains within 24 hours and the screen is flickering or unresponsive after a recharge?
It appears your ID205L smartwatch is experiencing a software or hardware malfunction following a deep battery discharge. Based on the manual and common troubleshooting for this model, please try the following steps:
If the watch continues to flick between functions and drains within 24 hours despite these steps, the battery or internal sensor may have been damaged by the deep discharge. Since the product typically comes with a one-year warranty, you should contact the manufacturer or the seller for a replacement if the device remains unusable.
Read the full Q&A page
Can’t pair watch to samsung J7 phone using veryfitpro. J7 says watch is paired but the time and date will not sink. Running version 7 android & “nearby device scanning on” on phone. Went to ATT store and rep could not get phone & watch to pair. English response please.
How do I fix pairing and time synchronization issues between my Willful ID205 smartwatch and a Samsung J7 running Android 7?
To resolve pairing and time synchronization issues with your Willful ID205 and Samsung J7, please follow these specific steps from the manual:
Note: The manual specifies that the app is compatible with Android 4.4 or higher, so your version 7 is supported. Ensure you are using the VeryFitPro app and not a different version like "VeryFit" or "VeryFitLite".
Read the full Q&A page
I can’t get my watch to track my sleep either. It says I haven’t slept for 3 days and that’s not right! Lol everything else is working great!
How do I fix sleep tracking issues on my Willful ID205 smartwatch?
If your Willful ID205 is not recording sleep data, please check the following troubleshooting steps based on the manual and app requirements:
Note: The watch automatically tracks sleep duration (Deep, Light, and Wake-sleep) based on movement and heart rate patterns during your typical rest periods.
Read the full Q&A page
my LetsFitID205 was working fine on my iPhone 7. I recently got an iPhone 13. I unbind it on my iPhone 7 and tried to pair it with the new phone, it doesn’t recognize it. It keeps searching and searching but cannot find ID205. I paired it back again to the iPhone 7 and miraculously I was able to! Now if I can get it to pair with iPhone 13 I will be happy as a clam! The guide says “The watch can only pair with one smartphone at a time” so that’s why I unbind with iPhone 7 and then tried to pair with iPhone 13……..doesn’t work. Please help……there’s no contact us for this manufacturer…….? Thank you.
How do I pair my ID205 smartwatch with a new iPhone 13 after unbinding it from an old iPhone 7?
To pair your ID205 smartwatch with your new iPhone 13, please follow these specific steps to ensure a clean connection:
itserver@idoocn.com.Note: If the watch still isn't found, try restarting both your iPhone 13 and the smartwatch (via the watch's settings menu) before attempting the bind process again.
>
Read the full Q&A page
The piece where the watch band connects broke off. It’s not the charger end, but the band cannot be connected so the watch can’t be worn. How do I get a replacement.
How do I get a replacement for a broken watch band connector on my Willful ID205 smartwatch?
According to the Willful ID205 Smartwatch Instruction Manual, the manufacturer offers a one-year hassle-free warranty on their devices. Since your watch band connector has broken, you should follow these steps:
Please note that if the plastic lug on the watch body itself has snapped (rather than just the removable strap), this is typically considered a hardware defect covered under the warranty terms mentioned in the manual.
Read the full Q&A page
Willfull id205 heart rate is not displayed.
Willfull id205 hertfrequenz wird nicht angezeigt.
Willfull id205 hertfrequenz wird nicht angezeigt.
Why is the heart rate not displayed on my Willful ID205 smartwatch?
If your Willful ID205 is not displaying heart rate data, please try the following troubleshooting steps based on the manual:
If the heart rate still does not display after these steps, you may need to unbind and re-pair the device within the app to reset the connection.
Hinweis für deutschsprachige Nutzer: Stellen Sie sicher, dass die Uhr fest am Handgelenk sitzt und der Sensor auf der Rückseite sauber ist. Prüfen Sie in der VeryFitPro-App, ob die Herzfrequenzmessung aktiviert ist.
Read the full Q&A page
How do I change the time
How do I change the time on my Willful ID205 smartwatch?
The time on the Willful ID205 smartwatch is not set manually on the device itself. Instead, it automatically synchronizes with your smartphone once it is paired via the VeryFitPro app.
To set or correct the time, follow these steps:
If the time becomes inaccurate over time, simply open the app and perform a manual sync by pulling down on the app's home screen while the watch is connected.
Read the full Q&A page
How do I set my smart watch ID 205L to daylight savings time?
How do I set my ID205L smartwatch to daylight savings time?
The Willful ID205L smartwatch does not have a manual time setting on the watch itself. To update the time for daylight savings, you must synchronize the watch with the VeryFitPro app on your smartphone.
Follow these steps to update the time:
Once the watch successfully syncs with the app, it will automatically adopt the time and date settings from your phone. If the time does not update immediately, try unbinding and re-binding the device within the app, or restarting your phone's Bluetooth.
Read the full Q&A page
I agree..where is the info on changing time after daylight savings?
How do I change the time on my Willful ID205 smartwatch for daylight savings?
The time on your Willful ID205 smartwatch is not set manually on the watch itself. Instead, it automatically synchronizes with your smartphone's time when the two devices are paired and synced via the VeryFitPro app.
To update the time for daylight savings, follow these steps:
If the time does not update, try unbinding and re-binding the watch within the app, or restart your phone's Bluetooth to refresh the connection.
Note: The watch must be within 0.5 meters of your phone during the pairing/syncing process for the best results.
Read the full Q&A page
Hello
How can I change the time and date of my watch?
Hola
Como puedo cambiar la hora y fecha de mi reloj?
How can I change the time and date of my watch?<e/em>
Hola
Como puedo cambiar la hora y fecha de mi reloj?
How can I change the time and date on my Willful ID205 smartwatch?
The time and date on your Willful ID205 smartwatch are automatically synchronized with your smartphone and cannot be set manually on the watch itself. To update the time and date, follow these steps:
Note: If the time becomes inaccurate, it is usually because the watch has disconnected from the app. Simply open the VeryFitPro app and perform a manual sync (swipe down on the home screen) to refresh the data. If the watch is unbound or reset, the time will be cleared until it is reconnected to the app.
Read the full Q&A page
Worked for about 5 months and then battery stop recharging not really a good deal Just a disposable piece of bovine defecation
How can I troubleshoot my Willful ID205 smartwatch battery not recharging, and what is the warranty policy?
If your Willful ID205 smartwatch has stopped recharging, please try the following troubleshooting steps to rule out connection issues:
Warranty Information:
According to the manual, this device comes with a one-year hassle-free warranty covering defects. Since your device failed after five months, it should still be covered. You are advised to contact the manufacturer or the seller where you purchased the device (such as Amazon support or the email provided in the app support:
itserver@idoocn.com) to initiate a warranty claim or replacement.Note: The manual specifies that the battery is non-user replaceable; attempting to disassemble the device yourself will void the warranty.
Read the full Q&A page
There is no vibration when receiving a call. Please tell me how to set it.
電話受信時にヴァイブレーション 振動がありません。設定の仕方教えて下さい。
電話受信時にヴァイブレーション 振動がありません。設定の仕方教えて下さい。
How do I enable call vibration notifications on the Willful ID205 smartwatch?
To enable vibration for incoming calls on your Willful ID205, you must configure the settings within the VeryFitPro app on your smartphone. Please follow these steps:
Note: For the vibration to work, the watch must remain connected to your phone's Bluetooth, and the app must be allowed to run in the background. If the watch still does not vibrate, ensure that 'Do Not Disturb' mode is not active on the watch or your phone.
電話受信時の振動（ヴァイブレーション）を有効にするには、スマートフォンアプリ「VeryFitPro」で設定を行う必要があります。
Read the full Q&A page
There is no vibration of the clock when receiving an incoming call. Please tell me how to set it.
着信の時時計の振動がありません。設定の仕方教えて下さい。
着信の時時計の振動がありません。設定の仕方教えて下さい。
How do I enable vibration for incoming call notifications on the Willful ID205 smartwatch?
To enable vibration for incoming calls on your Willful ID205 smartwatch, you must configure the settings within the VeryFitPro app on your smartphone. Please follow these steps:
Note: Ensure that the VeryFitPro app has permission to access your phone's contacts and call logs in your smartphone's system settings. Also, make sure "Do Not Disturb" mode is turned off on both the watch and the app, as this will silence vibrations.
Read the full Q&A page
When this watch ID205 Smart watch falls and the screen goes blank but still works. Can it be repaired?
Can the ID205 smartwatch screen be repaired if it goes blank after a fall but the device still functions?
Based on the official manual for the ID205 Smartwatch, there are no user-serviceable parts inside the device. The manufacturer explicitly states: "Never try to abuse, crush, open, repair or disassemble this device. Doing so will void the warranty and can result in a safety hazard."
If your screen has gone blank due to a fall, it likely indicates internal hardware damage or a disconnected display ribbon cable. Since the device is water-resistant (5ATM) and factory-sealed, attempting a manual repair is not recommended as it will compromise the waterproof seal and void your warranty.
Recommended Steps:
Read the full Q&A page
Hello,
How to change the sports activities that appear on the screen of the watch?
From the application page “Activity display”, I cannot include activities such as “outdoor walking” in the paragraph “Show movement”.
Thank you for your reply.
Bonjour,
Comment changer les activités sportives qui apparaissent sur l’écran de la montre?
Depuis l’application page “Affichage d’activité”, je ne peux pas faire passer des activités telles que “marche en plein air” dans le paragraphe “Montrer le mouvement”.
Merci de votre réponse.
How to change the sports activities that appear on the screen of the watch?
From the application page "Activity display", I cannot include activities such as "outdoor walking" in the paragraph "Show movement".
Thank you for your reply.<e/em>
Bonjour,
Comment changer les activités sportives qui apparaissent sur l'écran de la montre?
Depuis l'application page "Affichage d'activité", je ne peux pas faire passer des activités telles que "marche en plein air" dans le paragraphe "Montrer le mouvement".
Merci de votre réponse.
How do I change the sports activities displayed on the watch screen using the VeryFitPro app?
To change the sports activities displayed on your Willful ID205 smartwatch, you must use the VeryFitPro app. The watch can display up to 8 sports modes at a time from a total of 14 available options.
Follow these steps to update your list:
If the activity does not appear immediately, ensure your watch is connected via Bluetooth and perform a manual sync by pulling down on the app's main home screen.
Read the full Q&A page
1000 steps less than iPhone Healthcare Why? How can I match it?
iPhoneヘルスケアより歩数が1000歩少ないですどうしてですか？合わせるにはどうしたら良いですか？
iPhoneヘルスケアより歩数が1000歩少ないですどうしてですか？合わせるにはどうしたら良いですか？
Why is my step count 1000 steps lower than iPhone Health, and how can I sync them?
Discrepancies in step counts between a smartwatch and a smartphone are common because they use different sensors and algorithms. Your iPhone uses its internal accelerometer (often carried in a pocket), while the ID205 uses a wrist-based sensor that may filter out minor arm movements.
To ensure the data is as synchronized as possible, follow these steps:
Note: Because the devices are worn differently, they will rarely match perfectly. A difference of 1,000 steps over a full day is often within the expected margin of error for different tracking technologies.
Read the full Q&A page
Where do I find out how many calories I’ve burned?
How do I view my burned calories on the Willful ID205 smartwatch?
You can view your burned calories directly on the watch or within the companion app. Here are the specific methods:
Note: Ensure your watch is synced with the VeryFitPro app to keep your calorie data updated and saved for long-term tracking.
Read the full Q&A page
Hello, my screen does not light up anymore. I receive the notifications but black screen to access the applications of the watch. How can I go about fixing it.
Bonjour , mon écran ne s allume plus. Je reçois les notifications mais écran noir pour accéder aux applications de la montre. Comment puis je faire pour la réparer.
Bonjour , mon écran ne s allume plus. Je reçois les notifications mais écran noir pour accéder aux applications de la montre. Comment puis je faire pour la réparer.
How can I fix a black screen on my Willful ID205 smartwatch if it still receives notifications but the display won't light up?
If your Willful ID205 smartwatch is receiving notifications (vibrating) but the screen remains black, it may be in a low battery state or experiencing a temporary software freeze. Please try the following steps:
If the screen remains black after a full charge and a restart attempt, the display hardware may be defective. Since the product comes with a one-year warranty, you should contact the manufacturer or the seller for a replacement.
Read the full Q&A page
Hello, I can’t connect the watch in bluetooth, it asks me for a code that I don’t have. How to do ? Thank you
Bonjour, je n’arrive pas à connecté la montre en bluetooth, il me demande un code que je n’ai pas. Comment faire ? Merci
Bonjour, je n'arrive pas à connecté la montre en bluetooth, il me demande un code que je n'ai pas. Comment faire ? Merci
How do I connect my Willful ID205 smartwatch via Bluetooth if it asks for a pairing code?
To connect your Willful ID205 smartwatch, you should not pair it directly through your phone's Bluetooth settings. If you try to connect via the phone's Bluetooth menu, it may ask for a code that does not exist.
Please follow these steps to connect correctly:
By pairing through the app instead of the phone settings, the connection should complete without requiring a code. If you have already tried to pair it in your phone's Bluetooth settings, please "Forget" or "Unpair" the device there first before trying through the app.
Read the full Q&A page
hello, forgot the smartwatch ID 205, login details, please help me, thanks
hallo, habe die smartwatch ID 205, anmeldedaten vergessen,bitte helfen sie mir,Danke
hallo, habe die smartwatch ID 205, anmeldedaten vergessen,bitte helfen sie mir,Danke
How can I recover or reset my login details for the ID205 smartwatch app?
The ID205 smartwatch typically uses the VeryFitPro app for synchronization. If you have forgotten your login details, please follow these steps:
If you are using a different app (such as VeryFit), the process is similar: use the "Forgot Password" feature on the main login page of the app.
Read the full Q&A page
My watch all of the sudden will not synch with my phone. It tried unbinding it and starting over, it indicates that it has successfully bound to my watch but it does not synch with my watch. When I tap the phone icon on the wart channel, it indicates this function is turned off
Why is my Willful ID205 smartwatch not syncing with my phone even after unbinding and re-binding, and why does the phone icon on the watch say the function is turned off?
It sounds like your watch and phone are paired at a system level but the app-to-device communication is being blocked. Please try the following steps to resolve the sync issue:
If the watch indicates it is bound but data (like steps or sleep) still doesn't appear in the app, try clearing the app cache in your phone settings or reinstalling the VeryFitPro app.
Read the full Q&A page
When the phone rings, the screen may say unknown. What does that mean?
電話が鳴ると画面に未知と出る場合がありますが、どういうことですか？
電話が鳴ると画面に未知と出る場合がありますが、どういうことですか？
Why does my ID205 smartwatch display 'unknown' for incoming calls?
When your ID205 smartwatch displays "unknown" (or "未知") during an incoming call, it typically means the watch does not have permission to access your phone's contacts or the caller's information is not being shared correctly by the VeryFitPro app.
To resolve this, please check the following settings:
If these steps do not work, try unbinding the watch from the app, restarting both your phone and the watch, and then re-pairing them.
Read the full Q&A page
how do you delete messages pressing the tick but nothing happens
How do I delete messages on the Willful ID205 smartwatch when the tick button is not working?
To delete messages on the Willful ID205 smartwatch, you typically swipe down from the home screen to view your notifications. While the manual indicates that the watch displays message content and vibrates for alerts, it does not explicitly detail a 'tick' button for deletion. If you are pressing a checkmark icon and nothing is happening, please try the following steps:
If the 'tick' button is physically visible on the screen but unresponsive, ensure the screen is clean and dry, as moisture can interfere with touch sensitivity.
Read the full Q&A page
So my watch accidentally died. I recharged it, but now it has the wrong time. How do I reset the correct time? I see that other users are having the same problem.
How do I reset the correct time on my Willful ID205 smartwatch after it has been recharged?
To reset the correct time on your Willful ID205 smartwatch, you must synchronize it with the VeryFitPro app on your smartphone. The watch does not have a manual time-setting feature; it automatically pulls the time and date from your phone once a connection is established.
Follow these steps to sync the time:
Note: If the watch is not currently paired, tap "Bind Device" in the app and select "ID205" from the list. Do not attempt to pair the watch through your phone's system Bluetooth settings; it must be done within the VeryFitPro app for the time to update correctly.
Read the full Q&A page
I keep getting a buzz and what looks like a flame. Also a number like 500 on the screen. What does it mean?
What does the flame icon and the number 500 mean on my Willful ID205 smartwatch?
The flame icon on your Willful ID205 smartwatch represents calories burned. The number 500 appearing next to it indicates that you have burned 500 calories during your current activity or throughout the day.
The buzzing (vibration) you are experiencing likely indicates one of the following:
You can customize these alerts and view your detailed calorie data within the VeryFitPro app on your smartphone.
Read the full Q&A page