LEDYi Lighting RT5/RT10 Touch Wheel RF Remote Controller
Touch Wheel RF Remote Controller
Model No.: RT5/RT10
1 and 4 zone RGB+CCT/Touch color wheel/Wireless remote 30m distance/AAAx2 battery/Magnet stuck fix
Features
- Apply to RGB+CCT LED controller.
- Ultra sensitive color adjustment touch wheel.
- Each remote can match one or more receiver.
- AAAx2 battery powered.
- Operate with LED indicator light.
- Magnet on the back which can be stuck on back holder.
Technical Parameters
| Input and Output | |
| Output signal | RF(2.4GHz) |
| Working voltage | 3VDC(AAAx2) |
| Working current | ＜5mA |
| Standby current | ＜10μA |
| Standby time | 1 year |
| Remote distance | 30m(Barrier-free space) |
Environment
- Operation temperature Ta: -30OC ~ +55OC
- IP rating IP20
| Safety and EMC | |
| EMC standard (EMC) | ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 |
| Safety standard(LVD) | EN 62368-1:2020+A11:2020 |
| Radio Equipment(RED) | ETSI EN 300 328 V2.2.2 |
| Certification | CE,EMC,LVD,RED |
| Weight | |
| Net weight | 48g |
| Gross weight | 88g |
Mechanical Structures and Installations
Tox the remote, three options are offered for selection: Option 1: stuck the remote on any metal surfaces directly. Option 2: fix the remote’ back holder on the wall with two screws. Option 3: adhere the remote’ back holder to the wall with paster.
Operation
- When turn on light, the indicator display blue. when turn off light, the indicator display red.
- When touch the color wheel, the indicator will display the same color.
- When press or touch operation is invalid (If the light is off), the indicator display red.
- To extend battery life, no touch or press key operation after a few seconds, the touch wheel will enter sleep state, you need press any key to make touch wheel quit sleep state.
Match Remote Control (two-match ways)
End-user can choose the suitable match/delete ways. Two options are offered for selection:
Use the controller’s Match key
Match:
Short press match key, immediately press on/off key (single-zone remote) or zone key (multiple zone remote) of the remote.
The LED indicator fast flash a few times
means the match is successful.
Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times
means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again.
An immediately short press on/off key (single-zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful.
.Delete:
Switch off the power, then switch on the power, repeat again.
An immediately short press on/off key (single-zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted.
Key function
RT5 1 zone RGB+CCT remote
RT10 4 zone RGB+CCT remote
Safety information
- Read all instructions carefully before you begin this installation.
- When installing battery, pay attention to the battery positive and negative polarity. A long time without the remote control, remove the battery. When remote distance becomes smaller and insensitive, replace the battery.
- If no response from the receiver, please re-match the remote.
- Gently handle remote, beware of falling.
- For indoor and dry location use only.
Documents / Resources
 | LEDYi Lighting RT5/RT10 Touch Wheel RF Remote Controller [pdf] Instruction Manual RT5, RT10, Touch Wheel RF Remote Controller, RT5 Touch Wheel RF Remote Controller, RT10 Touch Wheel RF Remote Controller |
