LECTROTAB JLC-11 Joystick LED Trim Tab Control
Product Information
The JLC-11 Joystick LED Trim Tab Control by Lectrotab is a user-friendly control designed to enhance the boating experience. It incorporates features requested by boat owners to provide precise control over trim tab movement.
Key Features:
- Single or dual station control
- 1 or 2 actuator per trim tab
- Black color
- Overall width: 3.0″ (77mm)
- Overall height/thickness: 3.0″ (77mm) / 2.0″ (50mm)
- Mounting hole DC cutout diameter: 2.625″ (66.7mm)
- Voltage: 12/24VDC
- Fuse size: 12VDC = 15 or 20 amps, 24VDC = 10 amps
For more information about the JLC-11 Joystick LED Trim Tab Control, please visit the Lectrotab website or contact them at Ph: 804-368-8428 or Email: sales@lectrotab.com.
Product Usage Instructions
To program the JLC-11 Joystick LED Trim Tab Control, follow these steps:
Lectrotab’s Joystick LED control incorporates features requested by boat owners to provide a user-friendly control for a more enjoyable boating experience.
- Single “Joystick” control
- NMEA 2000 compatible
- LED display of each trim tab position
FEATURES
- Microprocessor based trim tab control with LED tab position indicators
- NMEA 2000 compatible with JLC-NMEA adapter
- Move both tabs up or down simultaneously with a single motion
- Dual station ready – just add a second JLC-11 and JR-* cable (sold separately)
- Automatic return to last tab position if ignition key is turned off and back on again
- Completely sealed, completely waterproof and will not deteriorate in sunlight• Automatic tab retraction and calibration with key or accessory switch off
- Easy upgrade from any of our Lectrotab controls
- No external power module required
- LED tab position indicators dim automatically in darkness and brighten in sunlight
- Single or Dual Actuator per tab
- Operates on 12 or 24 volt dc systems
PRELIMINARY SPECIFICATIONS
| Model Number | Display Color | Number of Stations/Actuators | Overall Width | Overall Height/ Thickness | Mounting Hole Cutout (Diameter) | DC Voltage | Fuse Size Power Input (1 Actuator per Tab) | Fuse Size Aux.(MUST CONNECT) |
| JLC-11 | Black | Single or Dual Station/ 1 or 2 Actuator/tab | 3.0″/ 77mm | 3.0“(77mm)/ 2.0”(50mm) | 2.625″/66.7mm | 12/24 | 12vdc = 15 or 20 amps 24vdc = 10amps | 1 to 2 amp |
- Linear Devices Corporation
- 11126 Air Park Road, Suite G, Ashland, VA 23005
- www.lectrotab.com, Ph 804-368-8428, Email: sales@lectrotab.com
- August 2023
JLC-11 WIRING and DIMENSIONS
“ILC-11” Control Installation/ Wiring Diagram
JLC-11 Programming Chart | ||||||
| Program Mode Sequence | ||||||
| Function | Enter | Adjust Setting | Exit | Range | Default | Program Details |
| Timing | Push & hold joystick left | Move and hold Joystick Up or Down | Push joystick right and hold 4 seconds + | 4 – 12sec | 8sec | 8 LEDs = 8 second actuator 4 LEDs = 4 second actuator |
| Remember Last Tab Position | Pull & hold joystick back | Move and hold Joystick Up or Down | Push joystick right and hold 4 seconds + | Standard/Remember | Standard | 8 LEDs each side = Standard Retract 1 LED each side = Remember Last Tab Position |
| Swap LED’s | Push & hold joystick right | Move and hold Joystick Up or Down | Push joystick right and hold 4 seconds + | LEDs match tab movement or opposite tab movement | LEDs match tab movement direction | 1 LED on right and left = LEDs follow and match tab movement direction 8 LEDs on right and left = LED follow opposite of tab movement direction |
| Disable Auto Tab Retract | Push & hold joystick forward | Move and hold Joystick Up or Down | Push joystick right and hold 4 seconds + | Enable/Disable | Enabled | #1 LED each side = Default of Auto Tab Retract enabled #8 LED each side = Auto Retract Disabled |
| Independent Tab Control | Push & hold joystick 45° towards upper left position (between top and left position) | Move and hold Joystick Up or Down | Push joystick right and hold 4 seconds + | Enable/Disable | Disabled | #1 LED each side = Default Disabled or tabs do not operate independently #8 LED each side = Tabs operate independently |
Programming Details
- Timing: #LEDs lit corresponds to the #seconds in actuator stroke time i.e. 8 LEDs = 8 seconds, 4 LEDs = 4 seconds (Actuator’s A and B series = 8 seconds, C and D series = 4 seconds and S series = 6 seconds)
- Rember Last Tab Position: If AUX power is switched from +12 or 24vdc to 0vdc, tabs retract (Set Timing + 1 sec.). When power is reapplied, tabs go to last position before key sw. off. Removing +12 or 24vdc power source will reset original setting back to fully retracted and keep fully retracted at new power sorce on. (8 LEDs on each side = standard auto retract and no last setting, 1 top LED on each side = remember last tab position before Aux power off.)
- Swap LED’s: 1 LED on right and left side = LEDs follow and match tab direction, 8 LEDs on right and left side = LEDs follow opposite of tab direction
- Disable Auto Tab Retract: *Note* this program mode does not require +12vdc to the AUX terminal. Press the All Up and All Down buttons at same time for 2sec Press the STBD Bow Down/Up to adjust between Enable and Disable. (#1 LED each side = Default of Auto Tab Retract enabled. #8 LED each side = Auto Retract Disabled) Press the Port Bow Up to exit program and save setting.
- Independent Tab Control: 1 LED on right and left side = Tabs do not operate independently, 8 LEDs on right and left side = Independent control of each tab
Linear Devices Corporation
- 11126 Air Park Road, Suite G, Ashland, VA 23005
- www.lectrotab.com, Ph 804-368-8428, Email: sales@lectrotab.com
- August 2023
Documents / Resources
 | LECTROTAB JLC-11 Joystick LED Trim Tab Control [pdf] Instruction Manual JLC-11, JLC-11 Joystick LED Trim Tab Control, Joystick LED Trim Tab Control, LED Trim Tab Control, Trim Tab Control, Tab Control, Control |