Lumens - logoLC100 Installation Guide
LC100 Capture Vision System

Instruction Manual

Lumens LC100 CaptureVision System

Introduction of Product Functions

1.1 Front View

Lumens LC100 CaptureVision System - 1 Front View

1.2 Back ViewLumens LC100 CaptureVision System - Back View

1.3 Function Descriptions

No.ItemFunction DescriptionsNo.ItemFunction Descriptions
1.LCMDisplay Menu and Information16DC IN 12VDC 12 V power connector
2.KnobLCM knob17Input■ HDMI Input 1
■ 3G-SDI Input 1
■ HDMI Passthrough
3RecordStart/Stop recording
4StreamOn/Off image streaming18Input2■ HDMI Input 2
■ 3G-SDI Input2
5SceneSwitch templates19Output■ PGM: Main screen output, display the recording or streaming screen and layout
■ Multiview: Operation interface output; display the settings menu and image management
6PowerOn/Off the device power
7Single ChannelDisplay a single channel screen
8PIPSwitch to PIP (picture in picture)
9PBPSwitch to PBP (picture by picture)20USB3.0 portSupports the following
devices:
■ USB video/audio devices
■ External storage disk
• Keyboard/mouse
• LC-RCO1 (optional) controller
10SWAPSwitch signal channels
11USB3.0 portfor external storage disk
12USB3.0 portfor external storage disk
13USB2.0 portCan connect to keyboard/mouse device operation menu21EthernetConnect to LAN
14Factory ResetReset all configurations to factory default settings22RS-232/ RS-485 portConnect to AV control equipment
15RestartReboot the machine23XLR audio inConnect to a microphone or audio mixer
24Line In/ OutAudio In/Out

Product connection diagram

Lumens LC100 CaptureVision System - diagram

Precautions Prior to Use

3.1 Please confirm the purchased version equipped with hard drive or not. If not, please purchase one for installation.
3.2 LC100 supports 2.5″/3.5″ SATA hard drives.
3.3 If no hard drive is installed, use a USB disk for external storage.

Hard drive installation steps

4.1 Remove the screws (5 pcs) on the top cover.

Lumens LC100 CaptureVision System - steps

4.2 Loosen the following screws.Lumens LC100 CaptureVision System - Loosen

4.3 Attach your hard drive to the connection cable.
* Please make sure the port and the L-shaped slot of the cable are aligned before insertion. Do not force the connection to avoid damage to the port.Lumens LC100 CaptureVision System - connection cable

4.4 Fasten the hard disk to the metal plate with the provided screws (4 pcs).
A. 2.5″ SATA Hard Drive holes
B. 3.5″ SATA Hard Drive holes
* Do not over-tighten the screws to avoid damage to the hard drive. Only use the screws provided.Lumens LC100 CaptureVision System - Drive holes

4.5 Lock the hard drive mounting plate in place and insert the connection cable.Lumens LC100 CaptureVision System - Drive holes 1

4.6 Close the top cover to complete the installation.
4.7 Hard drive setting
After installation, you need to log in to the web page and click Information to format the drive.
Storage Setting > Hard Disk
*Formatting the drive will erase all existing data on the disk Lumens LC100 CaptureVision System - Drive holes2

Real-time operation menu

Connect the HDMI1 Multi View output to a monitor to display the real-time operation menuLumens LC100 CaptureVision System - monitor

No.ItemFunction Descriptions
1Lumens LC100 CaptureVision System - ItemConfigurationConfigure the network settings and recording/streaming quality
2Lumens LC100 CaptureVision System - Item1DirectorCreative control of video and audio inputs, audio feeds. Control recording and streaming and network video cameras
3Lumens LC100 CaptureVision System - Item2File ManagementTransfer, upload, download, delete, and play back video files
4Lumens LC100 CaptureVision System - Item3AboutDisplay the current LC100 firmware version
5Device IPDisplays the device’s network IP address.

Web Interface

6.1 Confirm the IP address of the device
Connect the LC100 to a router. Note the IP address of the device (visible in the lower right corner of the HDMI Multiview output screen) .
6.2 Input the devices IP address into the web browser, e.g. 192.168.100.100.Lumens LC100 CaptureVision System - Item4

http://192.168.100.100

6.3 Please enter your account/password to log in.

Lumens LC100 CaptureVision System - passwordAccount : admin
Password : admin

Web Interface
Thru the web interface users can access the File Manager, the Multi View interface and system settings.Lumens LC100 CaptureVision System - Web Interface

Director Tab

Follow these steps to access the Director Tab

  • On the Multi View interface, select Director Lumens LC100 CaptureVision System - Item1
  • Log in to the web page by entering the online Director Casting Account /Password (default setting: director/director)

Lumens LC100 CaptureVision System - Web Interface1

Lumens - logo

Copyright © Lumens Digital Optics Inc.
All rights reserved.

Documents / Resources

Lumens LC100 CaptureVision System [pdf] Instruction Manual
5100438-51, LC100, LC100 CaptureVision System, CaptureVision System

References

Leave a comment

Your email address will not be published. Required fields are marked *