LECTRON LEADPCCS500ABLKUS CCS1 To Tesla Adapter
PRODUCT INTRODUCTION
This charging adapter allows Tesla owners to access CCS1 fast chargers.
WARNINGS
- Read this document before using the CCS1 to Tesla Adapter. Failure to follow any of the instructions or warnings in this document can result in fire, electrocution, serious injury or death.
- This adapter is intended only to be used with Tesla vehicles. Do not use it for any other purpose.
- Do not use the CCS1 to Tesla Adapter if it is defective, appears cracked, broken, damaged or fails to operate.
- Do not disconnect the CCS1 to Tesla Adapter while the vehicle is charging.
- Protect the CCS1 to Tesla Adapter from any water or moisture.
- Handle with care whenever moving or transporting it. Store in a safe location.
- Do not damage the CCS1 to Tesla Adapter with sharp objects.
- Only use in temperatures between -22 °F and 122 °F.
- Do not clean with detergent or cleaning solvents.
- Do not use if it is damaged or corroded in any way. Inspect before each use.
- Do not open, disassemble, or modify the CCS1 to Tesla Adapter.Contact Lectron Customer Support for any repairs at contact@ev-lectron.com
WHAT ‘S INCLUDED
INTRODUCTION TO PARTS
- CCS1 port
- Insert stopper
- Tesla plug
BEFORE YOU USE
NOTE: Not all Tesla models support CCS adapters. To confirm whether yours is compatible, on your Tesla touchscreen select: Controls
Software Add vehicle information CCS adapter support: Enabled.
| Voltage: | 500 V DC |
| Outer box waterproof rating: | IP44 |
| Operating temperature: | -22˚F to 122˚F |
| Storage temperature: | -40˚F to 185˚F |
WARNING: Do not store the CCS1 to Tesla Adapter outside of the storage temperature range.
CHARGING TIME
- Charging time may vary according to charging station power, ambient temperature, and battery temperature.
- If the temperature of the adapter reaches 180 °F, the vehicle will reduce the charging power. If the temperature reaches 185 °F, the charging will shut off.
CONNECTING THE ADAPTER
- Open the Tesla charge port.
- Insert the CCS1 charging cable into the CCS1 port on the adapter. It will click firmly in place.
- Insert the adapter into the Tesla charge port and wait for the vehicle to signal that it has accepted the charger with a pulsating green “T” light next to the charge port (the touchscreen also shows the real-time charging status).
NOTE: The insert stopper on the adapter will keep it from being inserted too far and damaging the vehicle’s charge port. - Begin charging according to the charging station’s guidelines. Check your Tesla touchscreen to make sure it’s charging.
NOTE: Make sure that the adapter and CCS1 charging cable are firmly connected, and that the adapter is plugged into the Tesla charge port.
REMOVING THE ADAPTER
NOTE: Only remove the adapter from the charge port once charging is completed.
- Hold both the charger handle and the adapter and securely pull them out of the Tesla charge port.
NOTE: Do not press the unlock button on the handle while pulling it out of the charge port. - Press the unlock button on the handle and safely remove the adapter.
TROUBLESHOOTING
My Tesla is not charging. What’s wrong?
- Check to make sure your Tesla supports a CCS adapter. On the touchscreen select: Controls Software Add vehicleinformation CCS adapter support: Enabled.
- Check to make sure the adapter and CCS1 charging cable are firmly connected, and that the adapter is plugged into the Tesla charge port.
- Try unplugging and re-inserting both the charging cable and the adapter.
- Check the charging status on both the CCS1 charger and your Tesla touchscreen.
- If your car has been in an accident, Tesla may restrict or disable the use of a CCS1 adapter.
- If your Tesla is still not charging, email our customer service at contact@ev-lectron.com
SPECIFICATIONS
| Rated value: | 500A 500V DC |
| Insulation resistance: | >5MΩ (DC 500V) |
| Withstand voltage: | 2000V AC/5s |
| Shell: | Thermoplastic |
| EV connector: | Tesla |
| Dimensions: | 4.8 x 3 x 5.3 in |
| IP rating: | IP44 |
| Operating temp: | -22 °F to 122 °F |
| Storage temp: | -40 °F to 185 °F |
GET MORE SUPPORT
Need assistance?
For maintenance, servicing, or replacements, please contact our support team by scanning the QR code or emailing us at contact@ev-lectron.com
Made in China
FAQ
- Q: How do I know if my Tesla model supports CCS adapters?
A: Enable CCS adapter support in your Tesla touchscreen settings to confirm compatibility. - Q: What should I do if the adapter is not securely connected?
A: Ensure that the adapter and CCS1 charging cable are firmly connected before starting the charging process.
Documents / Resources
 | LECTRON LEADPCCS500ABLKUS CCS1 To Tesla Adapter [pdf] User Manual LEADPCCS500ABLKUS CCS1 To Tesla Adapter, LEADPCCS500ABLKUS, CCS1 To Tesla Adapter, Tesla Adapter, Adapter |
