AUDIBAX Control 8 192 Channel DMX Controller
Please read the manual before using the product.
PROGRAMMING
Power on the unit, it will be in MANUAL mode. Press PROGRAM 2 seconds. The corresponding LED will flash. SCENE and CHASE will be ready to be programmed. To return to play mode, press PROGRAM once more. The led will then turn off.
AUTO
- In playback mode (RUN) press Auto/Del, and the led will turn on, indicating that the AUTO/RUN mode is activated.
- Press this key to program SCENEs or CHASEs when in PROGRAM mode.
TAP SYNC
- In AUTO RUN mode, the playback speed will be recorded by the last two button presses.
- In program mode, select the screen between STEP and BANK.
BLACKOUT
Press this button to disable all data output (no other functions) – Press it again to exit this mode and send DMX data again.
DMX OUT
- DMX512 data output
DC INPUT
- DC9V～12V ,300
PROGRAMMING SCENES
- Press PROGRAM 3 seconds. The corresponding led will flash, indicating that the unit is in PROGRAM mode.
- Press the SCANNER button (or buttons, if you want to program several devices at the same time). Adjust the faders to your liking.
Main Features
- 192 DMX Channels.
- 30 Banks, each with 8 programmable scenes.
- 8 Faders for real-time adjustment.
- AUTO mode is controlled by TAP SYNC and SPEED.
- LED display with 4 digits. The first digit shows CHASE and the second SCENE. The third and fourth digit shows the banks. The second, third, and fourth digits show steps from 0 to 255 or time.
- Manual Blackout.
- Fade Time Control (FADE TIME)
Technical specifications
- Power: DC+9-12V
- Output: AC230V～50Hz (AC120V～60Hz)300Ma ,DC9V300Ma.
- Measurements
- Weight
INSTRUCTIONS FOR USE
- There are 192 DMX channels available for each scene.
- 8 scenes can be programmed per bank. When a scene is activated, it will play along with the others in that bank in a loop.
- Select the bank by pressing the UP and DOWN buttons. There are 30 banks available, only one is selectable at a time.
- Scenes can run automatically, and their duration depends on the tempo tapped by TAP SYNC., Scenes are executed under music or NOTE triggering, also press a scene button by hand to run scenes.
- 6 selectable chases are available, each with 240 scenes.
SCENES
While Control 8 is in PROGRAM mode, press PROGRAM for 2 seconds and it will enter MANUAL mode. If there are no scenes programmed in a bank, they cannot be played. Only those that have been previously programmed will be executed.
MANUAL OPERATION
Select a bank, and press SCENE to play a scene. If you press a SCANNER button, it will be registered to record in another SCANNER.
AUTORUN
Press AUTO/DEL and the corresponding led will light up. Press TAP SYNC/DISPLAY, and after waiting for a moment, press it again. This interval is assigned to the speed of the Auto Run mode, with a limit of 10 minutes. If there are more than two clicks, only the last two will be taken as a reference.
Scene buttons
Press a scene button to activate or store it, and the second digit of the display will show the scene between 1 and 8.
Page Selection
Press the PAGE SELECTOR button to select between channels 1-8 and 9-16 of each SCANNER.
Fader SPEED
Move the fader to adjust the speed of the CHASE.
Fader TIME SLIDER
Move this fader to adjust the fade time.
BANK ( UP or DOWN ) buttons
Press UP or DOWN to increase or decrease the bank number, which is shown in the third and fourth characters of the display (01 to 30).
Documents / Resources
 | AUDIBAX Control 8 192 Channel DMX Controller [pdf] User Manual Control 8 192 Channel DMX Controller, Control 8, 192 Channel DMX Controller, DMX Controller, Controller |
