8BitDo Lite 2 Bluetooth Gamepad User Manual
Lite 2 Bluetooth Gamepad
Switch
- Please ensure your Switch system and Lite 2 are updated to the latest version
- NFC scanning, IR camera, HD rumble, notification LED are not supported, nor can the system be waken up wirelessly
- Supports status indicator for1-8 players
Bluetooth Connection
1. Turn the mode switch to S
2. Press home to turn on the controller, LED starts to rotate from left.to right
3. Press pair button for 3seconds to enter its pairing mode. LED stops blinking for a short moment then starts to rotate again.(This is required for the very first time only)
4. Go to your Switch Home page to click on “Controllers”, then click on “Change grip/order” and wait for the connection
5. LED becomes solid and the controller vibrates when connection is successful
Wired Connection
Go to System Setting> Controller and Sensors> turn on Pro Controller Wired Communication 1. Turn the mode switch to S
2. Connect the controller to your Switch dock via USB cable
3. Wait till the controller is successfully recognized by your Switch to play
Android
- Please ensure your Android and Lite 2 are updated to the latest version
Bluetooth connection
1. Turn the mode switch to D
2. Press home to turn on the controller, LED 1 starts to blink
3. Press pair button for 3seconds to enter its pairing mode. LED stops blinking for a short moment then starts to rotate again.(This is required for the very first time only)
4. Go to your Android device’s Bluetooth setting, and pair with [BBitDo Lite 2]5. LED becomes solid and the controller vibrates when connection is successful
Wired Connection
- OTG support is required on your Android device. Please contact your device manufacturer for more details
1. Turn the mode switch to D
2. Connect the controller to your Android device via USB cable
3. Wait till the controller is successfully recognized by your Android device to play
Turbo Function
- Hold the button you would like to set turbo to, then press the star button to activate/deactivate the function
- D-Pad, Left stick, Right stick, Home, Select, Start buttons are not included
- Turbo function is not available on Switch mode
Battery
| Status | LED indicator |
| Low battery mode | LED blinks |
| Battery charging | LED stays solid |
| Battery fully charged | LED turns off |
- About 20 hours of playtime with a 480mAh built-in battery pack, rechargeable with 1 hour charging time
- Controller will turn off in 1 minute with no connection and 15 minutes with Bluetooth connection but no use
- Controller stays on with wired connection
Support
- Please visit support.8bitdo.com for further information & additional support
FAQ – Frequently Asked Questions
It is a controller mode switch button. [S] is for Switch mode, the controller is compatible with Switch console including Switch Lite/OLED on this mode.
[D] is for D-input mode, the controller is compatible with Android device on this mode.
When it’s connected to Switch, the corresponding buttons are as below: [Screenshot = STAR button]/ [Home button = Logo button]HD rumble, notification LED, Turbo and NFC functions are not available on Switch. When it’s connected to other devices, [STAR button = Turbo button].
You cannot wake up your Switch wirelessly with this controller.
Yes it does, but only on S mode.
It works with Switch/Lite/OLED and Android devices and It’s able to auto-reconnect to the devices above once they have been successfully paired.
We suggest you charge it via a phone power adapter. The controller uses 480mAh rechargeable battery with 1-2 hour charging time. The battery can last up to 20 hours when fully charged.
This might be the reason that there were too many controllers connected to your Switch, as one Switch can take up to 8 controllers maximum at a time. Please follow the instructions below and try again:
1. Upgrade the Lite 2 controller to the latest firmware version via Upgrade Tool first；
2. Change the mode switch to [S], connect it to the Switch via USB cable and wait for it to sync；
3. Unplug the USB cable when the syncing is done then press HOME button to build the wireless connection.
It depends on the number of controllers that each device can take. Generally, multiple Lite 2 controllers can be used simultaneously.
10 meters. The controller functions the best within the range of 5 meters.
Download
8BitDo Lite 2 Bluetooth Gamepad User Manual – [ Download PDF ]
