SYSTEMS
Hardware Quick Reference
GS-3528XUP
Mounting & connecting
- Configuration interface (Console)
Connect the configuration interface via the included serial configuration cable to the serial interface of the device you want to use for configuring/monitoring the switch. - TP Ethernet interfaces 10M / 100M / 1G PoE+
Use Ethernet cables to connect interfaces 1 to 12 to your PC or a LAN switch. - TP Ethernet interfaces 100M / 1G / 2.5G PoE++
Use Ethernet cables to connect interfaces 13 to 24 to your PC or a LAN switch.
- SFP+ interfaces 1G / 10G
Insert suitable LANCOM SFP modules into the SFP+ interfaces 25 to 28. Choose cables that are compatible with the SFP modules and connect them as described in the module’s documentation. - Power connector (device back side)
Supply power to the device via the power connector. Please use the IEC power cable supplied or a country-specific LANCOM Power Cord. - ATTENTION: High touch current possible! Connect to earth before connecting the power supply.
Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.
Please observe the following when setting up the device
→The power plug of the device must be freely accessible.
→ For devices to be operated on the desktop, please attach the adhesive rubber footpads
→Do not rest any objects on top of the device
→Keep all ventilation slots on the side of the device clear of obstruction
→Mount the device into a 19” unit in a server cabinet using the provided screws and mounting brackets.
→Please note that support service for third-party accessories is excluded.
LED description & technical details
➀ System / Link/Act/Speed / PoE
| System: off | Device switched off |
| System: green | Device operational |
| System: red | Hardware error |
| Link/Act/Speed: | Port LEDs show link / activity status or |
| green | port speed |
| PoE: green | Port LEDs show PoE status |
➁ Mode- / Reset button
| Short press | Port LED mode switch |
| ~5 sec. pressed | Device restart |
| 7~12 sec. pressed | Configuration reset and device restart |
➂ TP Ethernet ports 10M / 100M / 1G PoE+
LEDs switched to Link/Act/Speed mode
| Off | Port inactive or disabled |
| Green | Link 1000 Mbps |
| Green, blinking | Data transfer, link 1000 Mbps |
| Orange | Link < 1000 Mbps |
| Orange, blinking | Data transfer, link < 1000 Mbps |
LEDs switched to PoE mode
| Off | Port inactive or disabled |
| Green | Port enabled, power supply to connected device |
| Orange | Hardware error |
➃ TP Ethernet ports 100M / 1G / 2.5G PoE++
LEDs switched to Link/Act/Speed mode
| Off | Port inactive or disabled |
| Green | Link 2500 – 1000 Mbps |
| Green, blinking | Data transfer, link 2500 – 1000 Mbps |
| Orange | Link < 1000 Mbps |
| Orange, blinking | Data transfer, link < 1000 Mbps |
LEDs switched to PoE mode
| Off | Port inactive or disabled |
| Green | Port enabled, power supply to connected device |
| Orange | Hardware error |
➄ SFP+ ports 1G / 10G
| Off | Port inactive |
| Blue | Link 10 Gbps |
| Green | Link 1000 Mbps |
Hardware
| Power supply | Internal power supply unit (110–230 V, 50–60 Hz) |
| Power consumption Environment | Max. 870 W |
| Housing | Temperature range 0–40°C; short-term temperature range 0–50°C; humidity 10–90%, non-condensing |
| Number of fans | Robust metal housing, 19“ 1U (442 x 44 x 375 mm > W x H x D) with removable mounting brackets, network connectors on the front |
| Number of fans | 1 |
Interfaces
| ETH | 12 TP Ethernet ports 10 / 100 / 1000 Mbps PoE+ 12 TP Ethernet ports 10 / 100 / 2500 Mbps PoE++ 4 SFP+ ports 1 / 10 Gbps 28 concurrent Ethernet ports in total |
Package Content
| Mounting brackets | Two 19” brackets for rack mounting |
| Cable | 1 IEC power cord, 1 serial configuration cable 1.5 m |
This product contains separate open-source software components which are subject to their own licenses, in particular the General Public License (GPL). The license information for the device firmware (LCOS) is available on the device‘s WEBconfig interface under “Extras > License information“. If the respective license demands, the source files for the corresponding software components will be made available on a download server upon request.
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address:
www.lancom-systems.com/doc
LANCOM, LANCOM Systems, LCOS, LAN community, and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omissions.
111675/0622
Documents / Resources
 | LANCOM GS-3528XUP Multi-Gigabit Ethernet Access Switch [pdf] User Guide GS-3528XUP, Multi-Gigabit Ethernet Access Switch, GS-3528XUP Multi-Gigabit Ethernet Access Switch |
 | LANCOM GS-3528XUP Multi-Gigabit Ethernet Access Switch [pdf] User Guide GS-3528XUP Multi-Gigabit Ethernet Access Switch, GS-3528XUP Multi-Gigabit Ethernet Access Switch, Ethernet Access Switch |
