UNI-T logoLIV1320A/LIVI32013
Digital Angle Meter User Manual

Product Description

UNI-T LM320A Digital Angle Meter

1Battery status
2REF relative zero
3Product tilt direction
4Laser
5Unit conversion (in/ft: aim/al)
6ABS horizontal zero
7Gradient unit (%r)
8Data hold
9Measurement result
10Power/laser button
11REF/ABS/calibration button
12Data hold/unit conversion button
13Type-C charging interface
14Laser emission aperture (LM320B)

Operation

Power on
When the meter is not turned on, short pressUNI-T LM320A Digital Angle Meter - offto power
Power off: When the meter is turned on, long press UNI-T LM320A Digital Angle Meter - offto power off.
Laser (LM320B only)
After turning on the meter, short press UNI-T LM320A Digital Angle Meter - offto step through: turn on the left-side laser> turn on the right-side laser >turn on the lasers on both sides> turn off the lasers on both sides. UNI-T LM320A Digital Angle Meter - laser

Angle measurement:
When the meter is turned on, place it on an inclined surface. The value displayed on the screen is the angle between the inclined surface and the horizontal plane.UNI-T LM320A Digital Angle Meter - angal measurenemant REF (relative value mode):
Short press to enter the relative value mode (set the current measurement value to  Short press again UNI-T LM320A Digital Angle Meter - offUto exit this mode.UNI-T LM320A Digital Angle Meter - REF Calibration:
Place the product upright on a flat, smooth surface as shown in Figure 1. Long press, “1” will show on the screen (Figure 2). Short press UNI-T LM320A Digital Angle Meter - offU to proceed to the next step (Figure 3). Rotate the product 180° in the same position (Figure 4). Short pressUNI-T LM320A Digital Angle Meter - offU to complete the calibration.UNI-T LM320A Digital Angle Meter - FIGK

Data hold:
Short press UNI-T LM320A Digital Angle Meter - HOLEDto freeze the current measurement data.
Short pressUNI-T LM320A Digital Angle Meter - HOLED again to exit this function.

UNI-T LM320A Digital Angle Meter - DATA HOLED

Unit conversion:
Long press UNI-T LM320A Digital Angle Meter - HOLEDto convert the unit (default unit: °). Other selectable units: mm/m, %, in/ft.UNI-T LM320A Digital Angle Meter - UNET Charging:
When the low battery indicator UNI-T LM320A Digital Angle Meter - BATTREDshows on the upper right corner of the screen, please use the attached charging cable to charge the product.UNI-T LM320A Digital Angle Meter - CHARINGE

Specifications

ModelLM320AI LM320B
Measurement range4’90°
Accuracy± (0.2°)
Resolution0.01°
Laser/I Two-side lasers
Operating temperature0-50°C
DisplayEBIT, with backlight
Battery3.7V 300mAh lithium battery
Charging interfaceUSB Type C
Battery life2h
Magnet baseTwo-side magnetsI Four-side magnets
Frame materialAluminum alloy
Relative/absolute measurement
Angle lock
Low battery indication
Auto power off5 minutes
Product size61’61’31 mm
Standard accessoriesAngle meter: 1pc, USB cable: 1pc, user manual: 1pc, base plate: 1pc

Cautions

  1. Please do not use organic solvents to clean this product.
  2. Please use a soft cloth to clean the dirt to avoid damaging the surface of the product.
  3. The meter will power off automatically if no button press occurs for 5 minutes.

UNI-T logo

UNI-TREND TECHNOLOGY (CHINA) CO., LTD.
No.6, Gong Ye Bei 1st Road,
Songshan Lake National High-Tech Industrial
Development Zone, Dongguan City,
Guangdong Province, China
UNI-T logoO

Documents / Resources

UNI-T LM320A Digital Angle Meter [pdf] User Manual
LM320A, LM320B, Digital Angle Meter, Meter

References

Leave a comment

Your email address will not be published. Required fields are marked *