ROLL-A-SHADE Contract Plus Open Roll Coupled
Product Specifications
- Product Name: Contract Plus+ Open Roll Coupled
- Contact: Rollashade.com | info@rollashade.com |
951.245.5077 - Hardware Included:
- Motor Bracket
- Idler End Support Bracket
- Wall Switch
- Switch Box
- #14 Screws
- Zip Ties
- Wire Tie Pads
- Allen Wrench
- Tools Supplied: 3/8 Hex Head Phillips Head, 1/8 Drill Bit,
Drill
Product Usage Instructions
Application
Choose whether you want to install the shades inside or outside. Note that all shades can be pre-programmed to sensors, remotes, and/or wall switches upon arrival.
Mounting Location
Place the brackets in their mounting locations and mark the screw holes. Repeat this process for all brackets.
Screw Installation
Pre-drill screw holes using a 1/8 drill bit. Install the brackets using the provided screws and a 1/4 hex head driver.
Alignment
Ensure that all brackets are level and aligned properly.
Motor End Installation
Remove the locking ring, line up the motor bracket, and push the motor into the lock ring securely..
Frequently Asked Questions (FAQ)
Q: Can I install the shades both inside and outside?
A: Yes, you can choose to install the shades either inside or outside based on your preference.
CONTRACT PLUS+ OPEN ROLL COUPLED
INSTALLATION INSTRUCTIONS
info@rollashade.com
951.245.5077
© Copyright Roll-A-Shade® Inc. All Rights Reserved.
INSIDE OR OUTSIDE APPLICATION
**NOTE: ALL SHADES MAY BE PRE-PROGRAMMED TO SENSORS, REMOTES, AND/OR WALL SWITCHES UPON ARRIVAL**
MOUNTING LOCATION
Place your first bracket in its mounting location and mark the screw holes. Place your brackets in its mounting location and repeat the process.
SCREW INSTALLATION
Next, pre-drill your screw holes using a 1/8” drill bit. Install the brackets with the provided screws using the 1/4” hex head driver. 
MOTOR END INSTALLATION
Remove locking ring. Lineup to motor bracket. Push motor into Lock Ring properly. A B 
LOCK RING & ADDITIONAL LINKED SHADES INSTALLATION
Add locking ring to motor bracket. Check motor is secured correctly. A B 
SHADE PIN END INSTALLATION
Swivel ball bearing to align with Idler shaft for easy installation. Press Idler shaft all the way to the Bracket. A B 
NOTE
No need to disconnect shades to adjust uneven bottom bar. Adjust Srews to level bottom bar. ±1/4’’ Adjustment (total 1/2’’).
PLUG-IN MOTOR
- Run motor power cord to nearest power outlet.
- Install wire tie pads and secure with zip ties to hold wire down.
- The path of the wire should be parallel with mullions and/or drop ceiling tiles ensuring the cable is neatly organized.
- Any modifications to the power cable should be done by a certified electrician to meet your city/state code requirements.
SHADE ADJUSTING (IF NECESSARY)
- Roll shade up and down to confirm hembar is level and material rolls up straight on center tube.
- If the hembar is not level, lower shade until you see the metal tube.
- Add layers of masking tape to the metal tube to the end that is too low until hembar is straight.
- If the material tracks to one side, lower shade until you see the metal tube.
- Add layers of masking tape to the metal tube to the end that is opposite the direction of tracking, until shade rolls up straight.
ADJUSTING LIMITS (IF NECESSARY)
See programming instructions based on the motor used for your application.
RASCPORCMVER.4 6 OF 6 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.
Documents / Resources
 |
ROLL-A-SHADE Contract Plus Open Roll Coupled [pdf] Instruction Manual Contract Plus Open Roll Coupled, Contract Plus, Open Roll Coupled, Roll Coupled |
 |
ROLL A SHADE CONTRACT PLUS+ Open Roll Coupled [pdf] Installation Guide CONTRACT PLUS Open Roll Coupled, CONTRACT PLUS, Open Roll Coupled, Roll Coupled, Coupled |
