VENATOR-logo

HUNTER Klein 19440 Light Pendant

HUNTER-Klein-19440-Light-Pendant-product

superview

HUNTER-Klein-19440-Light-Pendant-fig-1

conformandum uicem

DICTIO 

  • Ad vitandum impulsum electricam possibilem, ante installing fixturam lucem tuam, potentiam disiungendi avertendo fractores ambitus ad cistam quae cum muro locum transitum coniungitur.
  • Et venientem in fixture est sententia. Si enim filum in terra site installation non est praesens, statim prohibere, et consulam quid electrician installation.
  • Omnes electrica wiring oportet esse in normam nationalis, locali et ANSI codicibus / NFPA 70. Si vos es expers sit wiring non dubitas, consulam quid electrician.

Et salvabit illos READ DE INSTRUCTIONIBUS
Haec salutis provideatur. Sit amet ipsum ut sint et diligenter legere omnino egressum antequam pro installation of lux lucis in fixture.

Hic sunt instrumenta quae opus est ad tuam institutionem perficiendam

HUNTER-Klein-19440-Light-Pendant-fig-3

Parat INSTALLATION

Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture. Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. One end of the threaded post (H) should be attached to the mounting bracket (A) with a hex nut (G) in place. The other end should be connected to the canopy loop (E). Unscrew the canopy loop ring (F) from the canopy loop (E). Depending on the placement of your junction box the position of threaded post (H) may need to be adjusted to allow the canopy to be flush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box and place canopy (D) over the canopy loop (E), so that it is flush with the ceiling. Adjust the position of threaded post (H) on the mounting bracket (A) so that the canopy (D) covers at least half of the exterior threads on the canopy loop  (E) while it is securely connected to threaded post (H). The threaded post (H) can be adjusted by loosening hex nut (G) to allow movement of threaded post (H) on mounting bracket (A). Once the ideal position of the threaded post (H) is determined, tighten up the hex nut (G) onto the threaded post (H) just beneath the mounting bracket (A) to secure the threaded post in place..

Fixture in unum

There are 4 12-inch rods (I), and 1 6-inch rod (J) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. Screw rod onto threaded post (K) on the fixture. Pull the fixture wires through the canopy loop ring (F), top of canopy (D), and canopy loop (E). Screw the top rod to canopy loop (E). Have a helper support the fixture’s weight and attach the mounting bracket (A) to the junction box by securely tightening the mounting screws (B).

HUNTER-Klein-19440-Light-Pendant-fig-2

Confirmabis ipsa fila COPULATIO 
Fila fixturae affigere ad potentiam copiarum fila e confluentia archa. iungo atrum to nigrum (Live); album ad album (fundatur); grounding to grounding (viridis aut aeris). Torquent finibus molestie jugis simul. deinde in filum iungo torquent. Fac omnia in eandem partem torquet. Loop fixture's humus filum circa grounding cochleae (C) et obstringere. Si filum humus (viridi aut aeris) nullum est ex confluentia archa, contactum quid electrician

Consummavi quod INSTALLATION

Place the canopy (D) flush to the ceiling and slide the canopy loop ring (F) up beneath the canopy. Tightly screw canopy loop ring (F) onto the canopy loop (E) to properly secure the canopy (D) in place. Carefully install glass shade (M) over socket (L), then install socket cover (N) and tighten up the glass shade with socket ring (O). Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Nunc institutionem tuam absolvitur. Verte vim, et experire fixturam.

Cleaning Tips

In fixture leniter tractare? Et ad redigendum iusto elit opus altum dictum. Regularis elit averte magnique per lumen extergere linteo puro pallio microfiber risus vel libero. Numquam lautus RAMULUS onto recta sunt fixture.

EDICTUM
In order to use a 12in rod by itself you must first remove the post from the 6in rod and install it on one of the ends of the 12in rod

Venator Pro consilium 
Torquere vel taeniola taenia in unum desinere, ut facilius eas per downrods transeas. Post filum facilius removeri potest accessum

Documenta / Resources

HUNTER Klein 19440 Light Pendant [pdf] Instructio Manual
Klein 19440, Klein, 19440, Light Pendant

Leave a comment

Curabitur sit amet nisl. Inquisita agros sunt praenotati *