Dynamic QR Code Standalone Controller
Q10-C/Q
Q20-C/Q
Manual
Q10-C/Q Dynamic QR Code Standalone Controller
Note:Q20-C/Q and Q10-C/Q difference:Q20-C/Q with keypad,Q10-C/Q non-keypad. Q20-C/Q with keypad have password door opening function.
Q20-C/Q and Q10-C/Q the Scanning QR code and RFID Card usages, installation, wire connection, size, packing completely the same, the following contents take Q20-C/Q as an example.
Products introduction
Q20-C/Q is our independent research and development production, good performance QR code+RFID Card Standalone controller .Advanced CMOS image recognition technology, intelligent image recognition system, scan code recognition rate of high speed, large capacity s torage (10,000 user card information), high security, simple operation, comple te functions, dynamic QR code
APP+ card + password three ways to open the door
Products picture
Parameter
| Dynamic QR Code Standalone Controller Q20-C/Q | ||||||
|
Products Features
Electrical parameters
Appearance and packing
Working environment | communication | Offline | ||||
| Management | 6 digit Password （Q10-C/Q non-keypad no this function） | |||||
| App | Quicklopen | |||||
| Reading card type | MF Card | |||||
| Reading Range | MF:1～3cm，QR Code:1～20cm | |||||
| Card Capacity | ≥10000 cards | |||||
| Door opening mode | App,Card,Password（Q10-C/Q non-keypad no this function） | |||||
| Prompt mode | Buzzer sound, Blue work light on, green light flashes | |||||
| Camera pixel | 300000 pixels | |||||
| Scan resolution | 640*480 | |||||
| Reading angle | Rotate 360 °, tilt ± 45 °, deflection ± 45 ° | |||||
| Keypad Type | Press | （Q10-C/Q Non-keypad） | ||||
| Open door time | 0～99s | |||||
| Door ell function | with Doorbell button（Q10-C/Q no Doorbell keypad） | |||||
| Work voltage | DC12V | |||||
| Work current | 100mA | |||||
| Color and material | Black | Plastic ABS | ||||
| Size | 120×80×18（mm） | |||||
| Install hole space | 60 mm | |||||
| Packing list | （Dynamic QR Code Standalone Controller 、8P wire、manual）×1 | |||||
| Working temperature | -10~60℃ | |||||
| Working humidity | 5%-85% | |||||
|
8P Socket Wire connection | Wire S/N | Color | Interface | Illustrate | ||
| 1 | Red | DC12V | Cathode | |||
| 2 | Black | GND | GND | |||
| 3 | Yellow | NC | Relay NC | |||
| 4 | White | COM | COM | |||
| 5 | Black | NO | Relay NO | |||
| 6 | Green | OPNE | Exit button | |||
| 7 | Yellow | BEEP | Doorbell | |||
| 8 | Blue | BEEP | ||||
Electric lock wire diagram
We suggest use dedicated access control power supply, output relay signal that directly drives electrical locks, automatic doors, gates, etc
QR Code Standalone Controller LED status
| illustrate | Blue/Green | Green light | Buzzer |
| Work Status | on | ||
| Programming mode | on | ||
| Program mode sub-menu | on | ||
| Scan unregistered card on | Long sound di | ||
| Scan registered card | Blue light and green light are at | on | 2 short sound -di di” |
| After scan card need input password open door | interval flash | ||
| Card+Password mode | Blue/Green Flash every 0.5 second | ||
| Password mode | Blue/Green Flash every 0.5 second | ||
| Press keypad | short sound di | ||
| Setting Successfully | 2 short sound di di | ||
| Setting failure | Long sound di | ||
| Invalid input | Long sound di | ||
| Alarm | Continuous sound “di di di | ||
Appearance structure size
Documents / Resources
 | FondVision Q10-C/Q Dynamic QR Code Standalone Controller [pdf] User Manual Q10-C, Q10-Q, Q20-C, Q20-Q, Q10-C Q, Dynamic QR Code Standalone Controller, Q10-C Q Dynamic QR Code Standalone Controller, QR Code Standalone Controller, Standalone Controller, Controller |