EDIFIER R1280DB Bluetooth Bookshelf Speakers User Manual

NOTICE:
For the need of technical improvement and system upgrade,information contained herein may be subject to change from time to time without prior notice.
Products of EDIFIER will be customized for different applications. Pictures and illustrations shown on this manual may be slightly different from actual product. If any difference is found, the actual product prevails.

Box Contents:

Important safety instruction

WARNING: To reduce risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Thank you for purchasing Edifier RI 280DB multimedia speakers. Please read this manual carefully before operating this system.

Read these instructions.
Keep your user manual.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not use this apparatus near water and never put this apparatus into liquids or allow liquids to drip or spill onto it.
Do not place appliance filled with water on this apparatus, such as vase; nor place any form of open fire such as lit candle.
Do not block any ventilation openings. Please leave enough space around the speakers to ensure good ventilation (the distance should be above 5cm).
Install in accordance with the manufacturer’s instructions.
Do not place near any heat sources such as radiator, heat register, stove, or other apparatus (including amplifier) that produce heat.
Do not disregard the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades witn one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the outlet.
Protect the power cord from damage or getting pinched particularly at plugs, receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus is damaged, such as power supply cord or plug, liquid spilled or objects fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
The MAIN plug is used as the disconnecting devices, the disconnecting device shall remain readily operable.
The Maximum ambient temperature is 45°C / 113°F
Do not use strong acid, strong alkali and other chemical solvents to clean the product surface. Please use neutral solvent or water to clean the product.

Speaker Controls

Remote Control

Battery loading:
Please refer to the illustration to open the battery compartment, insert the CR 2025 battery and close the compartment

Note:

Do not place the remote control in places that are hot and humid.
Do not charge the batteries.
Remove the batteries when unused for long period of time.
The battery should not be exposed to excessive heat such as direct sun, fire or similar.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Connections

Connect the speakers with the included speaker connecting cable
Connect to power source, power on the speaker, then the indicator is lit.

LINE in Input

Press the master volume control on the active speaker or press the “LINE 1 /LINE2” button on the remote control to select LINE IN input. The indicator turns to green.
Using audio cable to connect audio source to the speaker.
Play from your device and adjust the volume accordingly.

Optical and Coaxial Input

Press the master volume control on the active speaker or press the “OPT /COX” button on the remote control to select the optical/coaxial input. The indicator turns to red.
Using optical or coaxial cable ( optical cable included) to connect audio sources to your speaker.
Play from your devices and adjust the volume accordingly.

Note:

1. In optical and coaxial modes, only PCM signal with 44.1 KHz/48KHz can be decoded.

Bluetooth Input

Pairing

Turn on speaker and switch to Bluetooth mode by pressing the Bluetooth button on the remote control or press the master volume control on back panel of the active speaker. The indicator turns to blue.
Go to setup section on your source devices ( mobile phones, tablets, etc.) and search for nearby Bluetooth devices, you will find “EDIFIER R1280DB” in the list.
Pair your device with “EDIFIER R1280DB”.
Play audio tracks on your device and adjust the volume to a desired level.
To disconnect Bluetooth, press and hold the master volume control for about 2 seconds.

Note:

Bluetooth connectivity and compatibility may be different among different source devices, depending on the software versions of source devices.
To enjoy the full Bluetooth functions of this product, please ensure your mobile device supports A2DP and AVRCP profile.
PIN code for connection is “0000” if needed.

Specifications

Troubleshooting

If you want to find out more about EDIFIER, please visit our website at www.edifier.com
For Edifier warranty queries, please visit the relevant country page on our www.edifier.com and review the section Warranty Terms.
USA and Canada: service@edifier.ca
South America: Please visit www.edifier.com (English) or www.edifierla.com (Spanish/Portuguese) for local contact information.

Read More About This Manual & Download PDF:

Documents / Resources

EDIFIER R1280DB Bluetooth Bookshelf Speakers [pdf] User Manual
R1280DB, R1280DB Bluetooth Bookshelf Speakers, R1280DB, Bluetooth Bookshelf Speakers, Bookshelf Speakers, Speakers

References

User Manual