Instruction Manual for EVOLUTION POWERSPORTS models including: Honda Talon Slip-On Exhaust, Talon Slip-On Exhaust, Slip-On Exhaust, Exhaust
Installation Instructions – Evolution Powersports LLC
Instrucciones de instalación – Evolution Powersports LLC
Honda Talon Slip-On Exhaust INCLUDED PARTS (1) Rear Muffler (1) Colored Heat Shield (1) 2.5" Accu-Seal Band Clamp (1) Inlet Pipe with Ball Flare (1) 2 Bolt Flange REQUIRED TOOLS 10mm,15mm Socket #5, #6 Allen Wrench 10,12,17,22mm Open End Wrench Rachet Blue Loctite High Temp Anti-Seize 6" Extension Rev_111221 Step 1: Using a 10mm socket to remove the rear valance under the bed. There is (1) bolt on each side. NOTE: This piece will no longer be used. (Figure 1) Figure 1 Step 2: Using a 22mm open end wrench, remove the 02 sensor. Be careful with the 02 sensor, it will be re-used. Step 3: Using a rachet with a 6" extension and 12mm socket and remove (2) bolts with springs holding the flange to the head pipe. These bolts and springs will be re-used when installing your new EVP exhaust. NOTE: you may need to squirt penetrating oil while doing this. (Figure 2) Figure 2 Rev_111221 Step 4: Spray lubricant onto the steel post where the rubber hangers meet the exhaust. There are (2) rubber mounts, one on the driver and passenger side. You may need to pry them away from their mounting positions. These will be reused, if you notice cracks or broken mounts, replace. (Figure 3) Figure 3 Step 5: Using the #6 Allen wrench, remove the hanger support bracket. Total of (3) bolts. Remove the OEM exhaust system. Installing the EVP Exhaust Step 1: Make sure the 2-bolt flange has the chamfer side facing the "flared" portion of the inlet pipe. Install the 2.5" Accu-Seal clamp over the muffler inlet. Step 2: Slip the inlet pipe into the swage portion of the muffler. With a 15mm socket, snug the Accu-Seal Clamp so both pieces are held together. DO NOT TIGHTEN THE CLAMP. Step 3: On the passenger side ONLY, re-install the hanger support using (3) Allen bolts and apply Blue Loctite on the treads. Step 4: Reinstall the rubber hanger onto the passenger side. Step 5: Slide the EVP muffler into the passenger side and push the rubber mount onto the muffler. Step 6: Mount the drivers side support hanger and rubber. Fasten the rubber onto the muffler supports. (Figure 4) Rev_111221 Figure 4 Step 7: Install the 2-bolt flange, the machine taper should be facing the inlet cone. Reuse the factory bolts, springs and nuts and place blue Loctite on the threads. Tighten each bolt equally so the flange seals against the tube flare. Figure 5 Rev_111221 Step 8: Install the 02 sensor, apply high temp anti-seize onto the threads. Counter turn the 02 sensor (5) times before installing, this will make sure the wires are not twisted. Use a 22mm open end wrench to tighten, DO NOT over tighten. (Figure 6) Figure 6 Step 9: Before you tighten the 2.5" Accu-Seal clamp make sure there is no binding between the inlet pipe and muffler. With a 15mm socket torque to 50-60 ft/lbs. (Figure 7) Figure 7 Rev_111221 Step 10: Your new EVP exhaust is installed. Before you start the machine, wipe the exhaust down with a micro-fiber cloth and glass cleaner. This will make sure to finger/handprints etch into the stainless before the first heat cycle. Thank you for choosing Evolution Powersports products. If you require further assistance, please call our Tech Support @ (715) 247-3862 Note: This product is exempt from the emission standards and related requirements of 40 C.F.R. § 1051 as provided by 40 C.F.R. § 1051.620, and California law [e.g., vehicle code§§ 27156 and 38391]. This product is sold only for use in connection with EPA certified, purpose-built, nonroad vehicles used solely for closed course, nonroad competition/racing and not used for any recreational purpose or on public highways or right of ways maintained by and open to the public. This product is sold only in connection with machines that do not fall under state and/or federal noise or emission standards/regulations. Purchasers who/that purchase this product represent and warrant that the product is purchased only in connection with EPA -certified, emission-regulations-exempt and noiseregulations-exempt competition/racing vehicles as interpreted under applicable state and/or federal law. Questions: Call Evolution Powersports at (715) 247-3862. Rev_111221Microsoft Word for Microsoft 365