Prevue Pet Products - Bird Cages, Dog Cages & Pet Supplies
Prevue Pet Products - Bird Cages, Dog Cages & Pet Supplies
Instruction Manual for PREVUE HENDRYX models including: 58501 Ferret Stack One Story, 58501, Ferret Stack One Story, Stack One Story
File Info : application/pdf, 3 Pages, 508.60KB
DocumentDocument]L 2 ]L 1
]F 2
MODEL
#58501
Ferret Stack | One Story
PARTS LIST
Instructions online at www.prevuepet.com
CUSTOMERSUPPORT Please contact Prevue Pet Products:
PHONE 1 (312) 243-3624 ONLINE www.prevuepet.com EMAIL customerservice @ prevuepet.com
]B 2 ]B 1
]Ct
]Cr
PLATFORM
RAMP
HAMMOCK
]Cg
KEY:
L = Left Side B = Back F = Front R = Right Side CR = Center/Roof CG = Center/
Floor Grille CT = Center/Tray CS = Center/Shelf
HARDWARE &TOOLS :
Hex Screws 18 pcs
Hex Key
]R 2
Casters 4 pcs
]F 1
]R 1
]Cs
These pieces are
interchangeable :
] L 1 = ] R 1
] L 2 = R 2
HOWTO TELL THEDIFFERENCE : Several parts and panels may look similar. Here's how to tell the difference:
Cr CENTERPANELS
Cg
The roof panel (CR) has an attached sliding door on top, and a screw hole
Cs
on both ends of the frame. The ground floor grille panel (CG)
has NO door and NO screw hole on
the ends.
The shelf (CS) is longer, and has threaded screw holes on the front and back corners of the frame.
58501 -- 06 /22 -- A4
Made in China for Prevue Pet Products, Inc., 224 N Maplewood Ave, Chicago IL 60612 USA · 1 [312] 243-3624 · www.prevuepet.com · customerservice @ prevuepet.com
MODEL
#58501
Ferret Stack | One Story
ASSEMBLY
Instructions online at www.prevuepet.com
CUSTOMERSUPPORT Please contact Prevue Pet Products:
PHONE 1 (312) 243-3624 ONLINE www.prevuepet.com EMAIL customerservice @ prevuepet.com
NO ADDITIONAL TOOLS REQUIRED · For best results, follow the Assembly Steps in the order presented.
KEY: L = Left Side B = Back F = Front R = Right Side
CR = Center / Roof CG = Center /
Floor Grille CT = Center / Tray CS = Center /
Shelf
1 PIECES
× 8
]L 1
interchangeable
]R 1
Orient the front legs (F1) with the windbell lock facing forward. The extended portion of the tray channel rail (L1) dovetails into the inside of the frame leg. Attach frames together with a hex screw through the bottom hole.
Orient the back legs (B1) with the tray channel backstop facing the back. Attach legs to sides with hex screws in the bottom holes.
windbell lock
]B 1 ]F 1
Attach the shelf (CS) with hex screws through the holes near the base of the legs.
]Cs
2 PIECES
CASTERS
]Cg
Turn the assembled unit
upside down. Fully insert a caster in each leg.
Turn it right-side up and set the floor grille (CG) in place.
58501 -- 06 /22 -- A4.1
Made in China for Prevue Pet Products, Inc., 224 N Maplewood Ave, Chicago IL 60612 USA · 1 [312] 243-3624 · www.prevuepet.com · customerservice @ prevuepet.com
3 PIECES × 10 interchangeable ]L 2 ]R 2
Stand the side panel (L2) and the lower back panel (B2) in position and attach together with a hex screw at the top and bottom corners.
Hand-tighten the screws so they remain loose. This will ease the assembly of the roof.
Continue adding and attaching the right side (R2) and front (F2)] panels with hex screws at the top and bottom corners.
] B 2
]F 2
] Cr
4 PIECES
Place the roof (CR) in position and attach and attach with a hex screw on each end.
Tighten the screws over the entire cage with the hex key until all screws are snug.
PLATFORM RAMP
Hook a ramp to the underside of the platform.
Place the platform in the cage, on the middle horizontal wire.
Add the hammock.
Rotate the windbell lock up and slide the tray into the channels.
HAMMOCK
]Ct
58501 -- 06 /22 -- A4.2
{ Assembly completed.
For more wonderful cages, toys, and accessories for cats, birds, chickens, rabbits, ferrets, dogs and small animals, visit www.prevuepet.com