Logo Honeywell

H-Class - logo

HD Peel & Present Option

Honeywell OPT78-2627 H-Class Powered Internal Rewind Option - detamexrast ji hêla xerîdarên me ve.

Honeywell OPT78-2613-04 H-Class Thermal Transfer Option

serview

This document describes the contents, installation, and use of the Heavy Duty Peel and Present option for the H-Class printer. After verifying the contents of the kit and the tools needed, follow the steps below to install and begin using the option. A maintenance procedure is also included, so keep this documentation for future reference.

Gazî BALDAYNÎ
For your safety and to avoid equipment damage, always turn ‘Off’ power and unplug the printer’s power cord before beginning this installation and when performing service.

Contents of the Heavy Duty Peel and Present Option

Di vê kîtê de tiştên jêrîn hene:
• Heavy Duty Peel and Present Assembly

Honeywell H-4310 H-Class HD Peel and Present Option - Heavy Duty Peel and PresentAmûrên Pêdivî ye
Ji bo sazkirina vê vebijarkê, hûn ê hewceyê pêçek standard hewce bikin.

Gav 1: Amadekirina Çapkerê

A) 'Off' bike Power Switch û kabloya elektrîkê ji pêvekê vekin AC Restacle.

Honeywell H-4310 H-Class HD Peel and Present Option - Preparing the Printer

B) Çapemeniyê li ser Girtin, Dûv re bikişîne pêş da ku jê rake Derî.

Honeywell H-4310 H-Class HD Peel and Present Option - DoorC) Bilind bikin Access Cover û medyaya xwe ji çaperê derxînin.

Honeywell H-4310 H-Class HD Peel and Present Option - Access Cover

D) Rakirin Thumbscrew û Tear Plate. (Alternately, if equipped with an Arc Plate, Present Sensor, or Cutter, remove that device.)

Step 2: Installing the Heavy Duty Peel and Present Assembly

A) Press Girtok û veke Peel and Present Civîn.

Honeywell H-4310 H-Class HD Peel and Present Option - Present Assembly

B) Bi baldarî pêl pê bikin Peel and Present Assembly nav Front Plate Connector.

Honeywell H-4310 H-Class HD Peel and Present Option - Peel and Present

C) Teng bikin Screw Çêkirin ji bo ewlehiya Peel and Present Assembly ji çaperê re.

Gav 3: Bikaranîna Vebijêrkê
Di dema xebatê de, etîket dê ji materyalê piştgiriyê werin qut kirin û "li gorî daxwazê" werin belavkirin - ango, çapkirina paşê dê tenê piştî ku etîketek berê çapkirî ji çaperê were rakirin. Ji bo bîranînê, "REMOVE LABEL" dê were xuyang kirin ku gava etîketek li benda rakirinê ye ji we bipirse.

Bi karanîna vebijarkê wekî jêrîn dest pê bikin:

A) Gazîname Medya (Ji bo hûragahiyan li Manualê Operatorê binêre). 20 înç (50 cm) dirêj bikin Medya ji çaperê.

Honeywell H-4310 H-Class HD Peel and Present Option - Media

B) Etîketan ji vê beşa dirêjkirî ya medyayê derxînin, bi tenê hiştin Materyalên Piştgiriyê. Rêya sereke ya vê yekê biafirînin BackingMaterial.
C)
Rêwîtiyê bikin Piştgiriya Materyalê bin Alîkariya Roller û ji Internal Rewinder.

Honeywell H-4310 H-Class HD Peel and Present Option - Backing

D) Pêça Piştgiriya Materyalê bi awayekî berevajî aliyê demjimêrê li dora Rewinder Hub and insert the creased leading edge into one of its Slots. Insert the Media clasp (Item 6) into the Slot over the creased leading edge of the Vegere Material and around the Rewinder Hub.

Honeywell H-4310 H-Class HD Peel and Present Option - Backing Material

E) Nêzîkî Peel and Present Assembly. Close the Access Cover, plug the power cord into the AC Receptacle, and turn ‘On’ the Power Switch.

Honeywell H-4310 H-Class HD Peel and Present Option - Peel and Present Assembly

F) Vê piştrast bikin AMADE is displayed on the Front Panel then press the FEED Key û li gorî çavdêriyên xwe bimeşin:

  • If REMOVE LABEL is displayed on the Front Panel, this completes the installation; or,
  • If REMOVE LABEL is not displayed on the Front Panel, proceed to step 4: “Configuring the Printer.”

Honeywell H-4310 H-Class HD Peel and Present Option - Front Panel

Notes:

  1. Xebata Sensora Niha ya li ser vê vebijarkê di heman demê de dikare ji hêla fermanên nermalava mêvandar ve jî were kontrol kirin, ji ber vê yekê pê ewle bibin ku bernameya weya nîşankirinê ji bo karanîna gava ku formatên etîketê ji çaperê re dişîne bi rêkûpêk hatî mîheng kirin.
  2. Ger ev vebijark bi hêzê ve were rakirin, çaper dê mîna ku etîketek li benda rakirinê ye tevbigere; ji bo vegerandina xebata normal, enerjiyê bizivirîne çaperê.

Gav 4: Veavakirina Çapkerê

While the Heavy Duty Peel and Present option is a plug-and-play device, this step may be necessary if the printer’s default configuration has been changed. Follow the steps below to configure the printer:

Not: Di prosedûra jêrîn de, ji bo rêwerzên panelê yên pêşiyê yên hûrgulî bi Rêbernameya Operatorê re şêwir bikin.

A) Press QERTA XÛREKÊ Button on the printer’s front panel.
B) bi bikaranîna JÊR Button, scroll to OPTIONS PRINTER then press the Right Button.
C) bi bikaranîna JÊR Button, scroll to SENSOR PRESENT hingê pêça ENTER Key.
D) bi bikaranîna JÊR Button, scroll to MODE hingê pêça ENTER Key.
E) bi bikaranîna JÊR Button, scroll to AUTO hingê pêça ENTER Qûfle.
F) Press DERΠKey then, at the GUHERTIN SAN PARASTIN? lezgîn, hilbijêrin ERÊ sazkirinê biqedînin.
G) Turn the Power Switch 'Ji' û ‘On’ to reset the printer and complete the configuration.

Not: If the printer fails to separate the labels from the backing material, and the Internal Rewinder is not turning, it may need to be enabled. Using the procedure above as a guide, press the QERTA XÛREKÊ Button, scroll to PRINTER OPTIONS, hingê bi REWINDER, Û hilbijêrin AUTO. Afterward, press the DERÎ key and save your changes when prompted.

Maintaining the Heavy Duty Peel & Present Assembly

To ensure trouble-free operation, the Heavy Duty Peel and Present Assembly should be cleaned after every 100,000 inches (254,000 cm) of media use. This interval depends on the label adhesive, where “gummy” adhesives may require more frequent cleaning. (To easily track label usage, go to SYSTEM SETTINGS → MEDIA COUNTERS in the printer’s menu system.)

Clean the assembly as follows:

  1. Guhestina elektrîkê 'Off' bike û kabloya elektrîkê ji Parzûna AC derxe. Berga Accessê bilind bikin û medyayê ji çaperê derxînin.
  2. Remove the Peel & Present Assembly from the printer.
  3. Bi karanîna hewaya pêçandî an firçeyek nerm, paqij bikin Sensors on the assembly.Honeywell H-4310 H-Class HD Peel and Present Option - SensorsNot: Ji bo paqijkirina depoyên giran, alkola isopropyl dikare were bikar anîn - bi şertê ku ew bi baldarî bi karanîna pembûyek pembû were sepandin, û dûv re destûr were dayîn ku zuwa bibe berî ku vebijarkê ji nû ve bi çaperê ve girêbide.
  4. Press Girtok to open the Peel and Present Assembly. Then remove the C-Clip that secures the Upper Roller Shaft bo Front Cover.Honeywell H-4310 H-Class HD Peel and Present Option - Front Cover
  5. Remove the Upper Roller Shaft and the associated Rollers.Honeywell H-4310 H-Class HD Peel and Present Option - Rollers
  6. Bikaranîna Sêwrê Cotton dampened with alcohol, wipe all Roller û Upper Roller Shaft surface clean. Pay special attention to the ridges on the Rollers to ensure that they are clean.
    Not: For cleaning heavy deposits from the Rollers and Shafts in the following steps, WD-40 or another non-damaging adhesive remover can be substituted for isopropyl alcohol – provided this adhesive remover is carefully applied using a cotton swab.
  7. Bişkînin Rollers vedigere ser Upper Roller Shaft, place the components into the Front Cover, and reinstall the C-Clip.
  8. Lêqellibînî û Esansor herdû hilpekînên ku ewle dike Lower Roller Assembly to the Front Cover (as shown) and then, while keeping it intact, carefully remove the entire Lower Roller Assembly.Honeywell H-4310 H-Class HD Peel and Present Option - Tabs
  9. Take note of the individual Roller positions – they must be reinstalled in the same order – then, carefully remove the Rollers ji Lower Roller Shaft.Honeywell H-4310 H-Class HD Peel and Present Option - Lower Roller Shaf
  10. Bikaranîna Sêwrê Cotton dampened with alcohol, wipe all Roller û Lower Roller Shaft surfaces clean. Pay special attention to the ridges on the Rollers to ensure that they are clean.
  11. Bişkînin Rollers, in their original order, onto the Lower Roller Shaft and reinstall them in the Front Cover, misogerkirina ku hilpekînên are properly seated. Reinstall the Peel and Present Assembly onto the printer to complete the cleaning procedure.

Belge / Çavkanî

Honeywell H-4310 H-Class HD Peel and Present Option [pdf] Rêbername
H-4310, H-Class, HD Peel and Present Option, H-4310 H-Class HD Peel and Present Option

Leave a comment

E-maila te ne dê bê weşandin.