지그비 로고ZigBee Smart plug
사용자 설명서
ZigBee 조명 스위치 모듈

제품 소개

ZigBee Light Switch Module - Product Introduction

ZigBee Light Switch Module - Symbol 1 장치의 무게는 1kg 미만입니다. 설치 높이는 2m 미만을 권장합니다.

설치 지침

  1. 전원 끄기ZigBee Light Switch Module - Power off경고 2 감전을 피하기 위해 설치 및 수리 시에는 딜러나 자격을 갖춘 전문가에게 도움을 요청하세요.
  2. 배선 지침
    ZigBee Light Switch Module - Symbol 1 장치의 전원을 켜기 전에 올바른 배선을 확인하십시오.ZigBee Light Switch Module - Wiring instruction경고 2 S1/S2 can connect with the rocker light switch, or it doesn’t connect. To ensure safety, do not connect the neutral wire and live wire to it.

명세서

제품 유형지그비 스마트 플러그
입력100-240VAC 50/60Hz
산출100-240VAC 50/60Hz
최대 하중10A/13A/16A/20A
지그비IEEE 802.15.4 2.4GHZ
재료PC 음성

특징

ZigBee plug is a smart Plug that adopts the ZigBee plug wireless protocol and connects to your internet through the ZigBee hub. You can turn on/off, schedule on/off, and share the device with your family to control together, and so on.

ZigBee Light Switch Module - Symbol 2원격 제어ZigBee Light Switch Module - Symbol 3타이밍 일정
ZigBee Light Switch Module - Symbol 4음성 제어ZigBee Light Switch Module - Symbol 5공유 제어
ZigBee Light Switch Module - Symbol 6똑똑한 장면

ZigBee Light Switch Module - Symbol 1 The above functions are determined by the ZigBee Hub.

작동 지침

  1. APP 다운로드
    Please refer to the user guide of the hub to download the corresponding APP. below platforms are recommended:
    ZigBee Light Switch Module - SmartThingsZigBee Light Switch Module - Amazone AlexaZigBee Light Switch Module - Hue
    스마트씽스아마존 알렉사색조
  2. 허브 연결
    Set the hub according to the user guide.ZigBee Light Switch Module - Hub connectionZigBee Light Switch Module - Symbol 1 Support ZigBee plug hubs as follows:
    에코 스튜디오
    에코 플러스 (모델: ZE39KL)
    2세대 에코쇼(모델명: DW84JL)
    2세대 에코 플러스 (모델: L9D29R)
    삼성 스마트씽스 허브
    필립스 휴
    ZigBee Light Switch Module - Symbol 1 연결에 실패하면 허브를 휴대폰에 더 가깝게 옮기고 다시 시도하세요.
  3. 전원 켜기
    전원을 켜면 처음 사용하는 동안 장치가 페어링 모드로 들어가고 LED 신호 표시등이 깜박입니다.
    ZigBee Light Switch Module - Symbol 1 The device will exit the pairing mode if no next operation for a long time. If you enter again, please long-press the manual switch for 5s until the LED signal indicator flashes and release.
  4. 알렉사에 연결
    1. Power on the Plug
    2. Ask, “Alexa, discover devices!
    3. Plug ashes once it’s connected
    4. Wait until Alexa finishes, check the new devices” First/Second….plug”

SmartThings에 연결

  1. Power up the smart bulb, bulb breathe 3 times, and enter the configuration state.
  2. Open the SmartThings app, and click”+”, click “Device”, click “SmartThings”, click “Lighting”, click ” Smart Bulb”, click “Start”, click “Next”, click “Skip the step”, click “Done”

공장 초기화

Long-press the configuration button for 5s until the LED signal indicator flashes and release, then the reset is successful. The device enters spairing mode.

ZigBee Light Switch Module - Factory Reset

ZigBee Light Switch Module - Symbol 1 If you pair the device with the hub again, please reset the device to factory default.

ZigBee Light Switch Module - Symbol 7중국에서 만든

문서 / 리소스

ZigBee 조명 스위치 모듈 [PDF 파일] 사용자 매뉴얼
조명 스위치 모듈, 스위치 모듈, 모듈

참고문헌

댓글을 남겨주세요

이메일 주소는 공개되지 않습니다. 필수 항목은 표시되어 있습니다. *