User Guide for Qbic models including: EP-0400 Desk Booking Device, EP-0400, Desk Booking Device, Booking Device, Device
QBIC TECHNOLOGY CO.,LTD EP0400 2AF82-EP0400 2AF82EP0400 ep0400
Quick Start Guide This guide is designed to help you quickly set up the EP-0400. EP-0400 ePaper Contents EP-0400 Bracket (Oponal) Product Overview M3x4 I/O Cover Tape (Oponal) M3x4 screw *1 (For baery cover) M3x6 M3x6 screw *3 (For bracket) 3 1 4 7 8 5 6 2 1 Display 5 Button 3 2 LED 6 Reset 3 Button 1 7 Bracket 4 Button 2 8 Battery Cover Installaon 1. Install Baery STEP 1 Install CR2450 coin baeries. (up to 4 pcs) STEP 2 Fix M3 screws to baery cover. 1. Tape Mount STEP 1 Aach tape on the back of bracket. STEP 2 Fix the bracket with tape on the surface. STEP 3 Fasten M3 screw*3 to secure the bracket and ePaper. 2. Surface Mount STEP 1 Install bracket on surface. (wood/ concrete) (screws not included) STEP 2 Mount the ePaper on the bracket. STEP 3 Fasten M3 screw*3 to secure the bracket and ePaper. NOTICE: It is recommended to secure with M3 screw. The suggested length of the M3 screw is the thickness of mounng bracket plus 8mm(screw not included). Please ensure the mounng surface is clean and smooth before using the tape. M3 screw Torque<2 kgf-cm Recommended Installaon Height: <2M CARE AND WARNING WARNING : Changes or modificaons to this unit not expressly approved by the party responsible for compliance will void the user's authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon.If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : Reorient or relocate the receiving antenna. Increase the separaon between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/panel PC technician for help. This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions : May not cause harmful interference. Must accept any interference received, including interference that may cause undesired operaon. Correct disposal of this product : This marking indicates that this product should not be disposed with other household wastes To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, use the return and collecon systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. FCC & CE RF radiaon Exposure Statement Cauon : Place the product at least 20cm from nearby persons. Replacement of a baery with an incorrect type that can defeat a safeguard Disposal of a baery into fire or a hot oven, or mechanically crushing or cung of a baery,that can result in an explosion; Leaving a baery in an extremely high temperature surrounding environment that can result in an explosion ammable liquid or gas; flammable liquid or gas . Canada, Industry Canada (IC) Noces This device contains licence-exempt transmier(s)/receiver(s) that comply with Innovaon, Science and Economic Development Canada's licence-exempt RSS(s). Operaon is subject to the following two condions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operaon of the device. Canada, avis d'Industry Canada (IC) L'émeeur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovaon, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitaon est autorisée aux deux condions suivantes : 1.L'appareil ne doit pas produire de brouillage; L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscepble d'en compromere le fonconnement. Radio Frequency (RF) Exposure Informaon The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potenal for human contact during normal operaon is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure condions. (antennas are greater than 20cm from a person's body). Informaons concernant l'exposion aux fréquences radio (RF) La puissance de sore émise par l'appareil de sans fil est inférieure à la limite d'exposion aux fréquences radio d'Industry Canada (IC). Ulisez l'appareil de sans fil de façon à minimiser les contacts humains lors du fonconnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d'exposion aux RF d'IC dans des condions d'exposion à des appareils mobiles (antennes sont supérieures à 20 cm à parr du corps d'une personne). About device information You can press the t op and middle buttons at the same t ime to get label information. FCC ID: 2AF82-EP0400IC: 23322-EP0400HVIN:EP0400 Surface Preparaon for Tape Applicaon Most substrates are best prepared by cleaning with a 50:50 mixture of isopropyl alcohol (IPA) and water* prior to applying Tapes. There are excepons! Excepons to this general procedure that may require addional surface preparaon include: Heavy Oils: A degreaser or solvent-based cleaner may be required to remove heavy oil or greasefrom a surface and should be followed by cleaning with IPA/water. Abrasion: Abrading a surface, followed by cleaning with IPA/water, can remove heavy dirt oroxidaon and can increase surface area to improve adhesion. Porous Surfaces: Most porous and fibered materials such as wood, parcleboard, concrete etc.need to be sealed to provide a unified surface. Unique Materials:Special surface preparaon may be needed for glass and glass-like materials,copper and copper containing metals and plascs or rubber that contain components thatmigrate (e.g. plascizers). General Procedure To obtain opmum adhesion, the bonding surfaces must be well unified, clean and dry. Typical surface cleaning solvents are IPA/ water mixture (rubbing alcohol) or heptane. * (Steps A and B) Bond strength is dependent upon the amount of adhesive-to- surface contact developed. Firm applicaon pressure develops beer adhesive contact and helps improve bond strength. (Steps C and D) Generally, this means that the tape should experience at least 15 psi(100 kPa) in roll down or platen pressure. Aer applicaon, the bond strength will increase as the adhesive flows onto the surface. At room temperature, approximately 50% of the ulmate strength will be achieved aer 20 minutes, 90% er 24 hours and 100% aer 72 hours. In some cases, bond strength can be increased and ulmate bond strength can be achieved more quickly by exposure of the bond to elevated temperatures. (e.g. 150°F [66°C] for 1 hour). IPA & Water Step A: Solvent wipe Step B: Wipe dry Step C: Apply tape to surface Step D: Roll finished joint NOTE : These cleaner soluons contain greater than 250 g/l of volale organic compounds (VOC). Please consult your local Air Quality Regulaons to be sure the cleaner is compliant. When using solvents, be sure to follow the manufacturer's precauons and direcons for use when handling such materials. The product contains a coin/button cell battery. Do not ingest battery, Chemical Burn Hazard. Keep batteries out of reach of children. Brand: Qbic Model: EP-0400 Input: 3V 10mA Operating Temperature: 0-40°C Battery information: Model : CR2450 CAUTION Risk of explosion if the battery is replaced by an incorrect type. Qbic Technology Co.,Ltd.26F.-12,No.99.Sec.1, Xintai 5th Rd., Xizhi Dist., New Taipei City 221, Taiwan(R.O.C) TEL:886-2-2697-2000 FAX:886-2-2697-2868Adobe Illustrator(R) 17.0 Adobe PDF library 15.00