GZYF LIRU MLS062 Universal Motorcycle LCD LED Digital Odometer Speedometer Gauge Instruction Manual

1. 서론

This manual provides detailed instructions for the installation, operation, and maintenance of your GZYF LIRU MLS062 Universal Motorcycle LCD LED Digital Odometer Speedometer Gauge. Please read this manual thoroughly before installation and use to ensure proper function and safety.

1.1 안전 정보

• Always disconnect the motorcycle's battery before performing any electrical work.
• 모든 배선 연결이 안전하고 적절하게 절연되어 단락을 방지하세요.
• Mount the speedometer securely to avoid vibration damage or detachment during operation.
• 설치 단계에 대해 확실하지 않은 경우 자격을 갖춘 기술자에게 문의하세요.

2. 패키지 내용

패키지에 모든 품목이 들어 있는지 확인하세요.

• 1 x GZYF LIRU MLS062 Digital Odometer Speedometer Gauge
• 1 x Speed Sensor
• Mounting Hardware (as pictured)

Image 2.1: The GZYF LIRU MLS062 Digital Odometer Speedometer Gauge, including the speed sensor and small mounting components.

3. 제품 오버view

The MLS062 is a universal digital gauge designed for motorcycles, providing essential riding information on a clear LCD LED display.

이미지 3.1: 앞면 view of the speedometer unit, showing the display area and control buttons.

이미지 3.2: 측면 view of the speedometer unit, highlighting its compact design.

3.1 주요 특징

• LCD LED Digital Display
• Speedometer (Max 199 units)
• Odometer (Max 99999.9)
• Trip Meter (Max 999.9, resettable)
• RPM Gauge (Max 14000r/min)
• Gear Indicator (N, 1-6)
• 24시간 시계
• Turn Signal, High Beam, and Neutral Indicators

4. 사양

Image 4.1: Dimensional diagram of the speedometer unit, showing measurements in millimeters.

5. 설정 및 설치

The MLS062 speedometer is designed for universal fitment on 12V motorcycles. Professional installation is recommended.

5.1 Mounting the Speedometer

1. Choose a suitable location on your motorcycle's dashboard or handlebar area for optimal visibility.
2. Use the provided mounting hardware to securely attach the speedometer unit. Ensure it is stable and does not obstruct your view 또는 통제.

5.2 배선 연결

Refer to the wiring diagram (if provided with your unit) and the image below for typical connections. The speedometer uses standard multi-pin connectors.

Image 5.1: Close-up of the wiring harness connectors, showing multiple pins for various functions.

• 전원(12V): Connect the positive wire to a switched 12V power source (e.g., ignition). Connect the negative/ground wire to the motorcycle chassis.
• 속도 센서: Connect the speed sensor wires to the corresponding input on the speedometer harness.
• RPM 신호: Connect the RPM signal wire to the motorcycle's ignition coil or ECU RPM output.
• 기어 위치: Connect the gear position wires (N, 1-6) to the motorcycle's gear sensor outputs.
• 지표: Connect wires for turn signals (left/right), high beam, and neutral light to their respective motorcycle circuits.

5.3 속도 센서 설치

1. Mount the speed sensor near a rotating part of the wheel (e.g., brake disc bolts, wheel spokes) that can trigger the sensor.
2. Ensure the sensor is positioned correctly to detect rotations consistently. Adjust the gap between the sensor and the trigger point as needed.

6. 사용 설명서

Once installed and powered on, the speedometer will display various information. The unit typically features two buttons for control, often labeled 'SEL' (Select) and 'ADJ' (Adjust).

Image 6.1: The MLS062 speedometer display shown in an operational state on a motorcycle dashboard, indicating speed, RPM, and gear.

6.1 디스플레이 모드

• Press the 'SEL' button briefly to cycle through different display modes: Odometer (ODO), Trip Meter (TRIP), and Clock.
• The main display will always show current speed and RPM.

6.2 Resetting Trip Meter

• While in TRIP mode, press and hold the 'ADJ' button for a few seconds to reset the trip meter to zero.

6.3 시계 설정

1. Navigate to the Clock display mode using the 'SEL' button.
2. Press and hold the 'SEL' button until the hour digits begin to flash.
3. Use the 'ADJ' button to adjust the hour.
4. Press 'SEL' again to move to the minute digits, then use 'ADJ' to adjust minutes.
5. Press 'SEL' one more time to save the settings and exit clock adjustment mode.

6.4 Unit Switching (MPH/KMH)

The method for switching between Miles Per Hour (MPH) and Kilometers Per Hour (KMH) may vary. Typically, this is done by:

• Turning off the ignition.
• Pressing and holding the 'SEL' button while turning the ignition back on.
• Release the button once the unit changes.

Note: Refer to specific instructions provided with your unit if this method does not work.

7. 유지관리

The GZYF LIRU MLS062 speedometer requires minimal maintenance.

• 청소: 부드러운 d를 사용하세요amp 디스플레이를 닦을 천과 casing. 플라스틱을 손상시킬 수 있는 연마성 세척제나 용제를 사용하지 마십시오.
• 사이: Periodically check all wiring connections for tightness and corrosion. Ensure the speed sensor is clean and free from debris.
• 환경 보호: While designed for motorcycle use, prolonged exposure to extreme weather conditions (heavy rain, direct sunlight) may affect longevity. Consider a protective cover when parking for extended periods.

8. 문제 해결

9. 보증 및 지원

For warranty information or technical support, please refer to the seller or manufacturer's contact details provided at the point of purchase. Keep your purchase receipt as proof of purchase.