Philips Jump Starter Instruction Manual

1. 서론

Thank you for choosing the Philips Jump Starter DLP8086N. This device is a portable, high-capacity power bank designed to jump-start 12V vehicles and charge various electronic devices. It features an 800A peak current and a 12000mAh battery, making it suitable for gasoline engines up to 6.0L and diesel engines up to 3.0L. Please read this manual carefully before use to ensure safe and optimal performance.

2. 제품 구성품

패키지에는 다음 품목이 포함됩니다.

• Philips Jump Starter Unit (DLP8086N)
• Smart Jump Starter Cables with clamps
• 마이크로 USB 충전 케이블
• Instruction Manual (with Warranty Card)

Image: Philips Jump Starter DLP8086N with its various ports and buttons labeled, including the power button, Micro USB input, USB output ports, LED light, and jump start port.

3. 사양

4. 안전 정보 및 보호 조치

The Philips Jump Starter is equipped with multiple safety features to prevent accidents and ensure user safety. These include:

• 단락 보호
• 과충전 보호
• 과방 전 보호
• 역접속 보호
• 역전하 보호
• 과전류 보호
• 과열 보호
• 역 극성 보호

스마트 클amps feature DSLI technology and communicate with the Battery Management System (BMS) to prevent potential errors that could damage the device or vehicle. Always follow the instructions carefully.

Image: Philips Jump Starter unit shown with its smart clamps, illustrating the various safety protection icons such as short circuit, overcharge, over-discharge, reverse connection, reverse charge, overcurrent, overheat, and reverse polarity protection.

5. 기기 설치 및 충전

5.1 점프 스타터 충전하기

Before first use, fully charge the jump starter. Connect the provided Micro USB charging cable to the Micro USB input port on the jump starter and to a USB power adapter (not included). The LED indicators will show the charging status. A full charge typically takes less than 5 hours.

5.2 배터리 잔량 확인

Press the power button once to check the battery level. The blue LED indicators will light up, showing the remaining charge.

6. 사용 설명서

6.1 차량 점프 스타트

차량 시동을 안전하게 걸려면 다음 단계를 따르세요.

1. Ensure the jump starter unit is sufficiently charged.
2. Insert the blue end of the smart jump starter cable into the jump start port on the unit. Ensure a firm connection.
3. 빨간색 cl을 연결하세요amp 차량 배터리의 양극(+) 단자에 연결합니다.
4. 검은색 cl을 연결하세요amp 차량 배터리의 음극(-) 단자에 연결합니다.
5. Once connected, the indicator on the smart cable should show a solid green light, indicating a safe connection. If it shows a red light or flashes, check the connections.
6. 차량의 엔진을 시동하십시오.
7. Once the engine starts, immediately remove the smart jump starter cable from the vehicle battery terminals, then disconnect it from the jump starter unit.

Image: A four-panel illustration demonstrating the jump-starting process: 1. Inserting the jump starter cable into the unit. 2. Connecting the red clamp 양극 배터리 단자와 검은색 CLamp to the negative terminal. 3. Starting the car engine. 4. Removing the jump starter cable from the battery.

6.2 전자 기기 충전

The jump starter features two QC3.0 USB output ports for charging smartphones, tablets, and other electronic devices. Connect your device's USB charging cable to one of the USB output ports on the jump starter. The unit will automatically begin charging your device.

Image: The Philips Jump Starter unit connected via USB cables to a smartphone and a tablet, demonstrating its capability to charge electronic devices.

6.3 LED 조명 사용하기

내장 LED 조명은 다양한 상황에 맞춰 세 가지 모드를 제공합니다.

• 스포트라이트 모드: For general illumination in dark environments.
• 구조 요청 모드: 비상 상황에 SOS 신호를 보냅니다.
• 스트로브 모드: 신호를 보내거나 주의를 끌기 위해 켜는 깜박이는 빛.

To cycle through the modes, press the LED light button repeatedly.

Image: A hand holding the Philips Jump Starter, with its LED light illuminating a dark engine bay. Icons below illustrate the three light modes: SOS, Strobe, and Spotlight.

7. 유지관리

To ensure the longevity and optimal performance of your Philips Jump Starter:

• 본 제품은 직사광선과 극한의 온도를 피해 서늘하고 건조한 곳에 보관하세요.
• 배터리 수명 유지를 위해 사용하지 않을 때에도 3~6개월에 한 번씩 기기를 충전하십시오.
• 부드러운 천으로 외부를 청소하고 damp 옷감. 강한 화학 물질이나 연마성 세제를 사용하지 마십시오.
• Keep the jump start ports and USB ports free from dust and debris.

8. 문제 해결

If you encounter issues with your Philips Jump Starter, refer to the following common solutions:

• 장치가 켜지지 않습니다: 기기가 충전되어 있는지 확인하십시오. 전원 버튼을 몇 초 동안 길게 누르십시오.
• 차량 시동이 걸리지 않습니다. 스마트클을 확인하세요amps are securely connected to the correct battery terminals (red to positive, black to negative). Ensure the smart cable indicator shows a solid green light. The vehicle battery might be severely discharged; try waiting a few minutes after connecting before attempting to start.
• Unit does not charge: Verify that the Micro USB charging cable is properly connected to both the jump starter and the power adapter. Try using a different USB power adapter or cable.
• Electronic devices do not charge: Ensure the jump starter has sufficient charge. Check the USB cable connection to both the jump starter and the device.

9. 보증 및 지원

This Philips Jump Starter DLP8086N comes with a 1년 제조사 보증보증 청구를 위해 구매 영수증을 보관하세요.

For any questions, concerns, or technical support regarding your product, please contact Philips customer service. Refer to the warranty card included in your package for specific contact information.

Image: A smiling customer support representative wearing a headset, symbolizing available product support.