1. 중요한 안전 정보
조립 및 사용 전에 모든 지침을 주의 깊게 읽어 주십시오. 나중에 참조할 수 있도록 이 설명서를 보관하십시오.
- This product includes safety features such as Collision Avoidance, Overheat Protection, and Auto Balance Protection.
- The desk is designed to support a maximum weight of 225파운드. 이 한도를 초과하지 마십시오.
- Ensure the desk is properly assembled and anchored for stability.
- Be aware of weight distribution and space requirements when operating the desk.
- 부상을 예방하기 위해 작동 중에는 어린이와 애완동물이 책상에 접근하지 못하도록 하세요.
- 움직이는 부품 근처에 손이나 다른 물건을 두지 마십시오.
2. 패키지 내용
조립을 시작하기 전에 모든 구성 요소가 있는지 확인하세요.
- 테이블탑 (1)
- Desk Frame (1)
- 모터(1)
- 컨트롤러 (1)
- 하드웨어 팩 (나사, 공구 등)
3. 조립 설명서
Most parts of the UNICOO Electric Standing Desk are pre-assembled to facilitate quick setup. Assembly typically takes less than 30 minutes. It is recommended that 두 사람 assemble the desk due to the weight of some components.
- 구성 요소 풀기: 모든 부품을 포장에서 조심스럽게 꺼낸 후 긁힘을 방지하기 위해 깨끗하고 부드러운 표면에 놓으세요.
- 테이블탑에 다리 부착: Align the desk legs with the pre-drilled holes on the underside of the tabletop. Insert and hand-tighten all screws initially. If any tabletop holes are slightly misaligned, loosen the pre-screwed leg supports to allow for adjustment, then tighten all screws securely once aligned.
- Connect Drive Bar: Extend the drive bar by gently tugging on the end with the gasket. Carefully connect it to the motor side, ensuring a secure fit. Be patient and gentle during this step.
- 컨트롤러 설치: Mount the controller to the designated location on the underside of the tabletop using the provided screws.
- 케이블 연결: Connect all necessary cables (motor to controller, power cable) according to the diagrams in the included assembly guide. Ensure all connections are firm.
- 최종 조임: 모든 부품이 제자리에 맞춰 정렬되면 모든 나사를 단단히 조이십시오.
Image: The UNICOO Electric Height Adjustable Standing Desk with white top and white legs, showcasing its minimalist design and integrated control panel.
4. 사용 설명서
The UNICOO Electric Standing Desk features an intuitive 7-button LED memory control panel for easy height adjustment.
이미지: 클로즈업 view of the desk's control panel, featuring an LED display showing the current height and buttons for up, down, and four memory presets.
- 높이 조절: 사용하세요 위로(▲) 그리고 아래로(▼) buttons on the control panel to manually raise or lower the desk to your desired height. The LED display will show the current height in inches.
- The powerful yet quiet motor allows for smooth transitions between sitting and standing positions.
5. Memory Presets and Reset
The control panel includes four customizable memory presets (1, 2, 3, 4) to store your preferred desk heights.
- Setting a Memory Preset:
- Adjust the desk to your desired height using the Up or Down buttons.
- 를 누르세요 S 단추.
- Immediately press the desired preset number button (1, 2, 3, 또는 4) 현재 높이를 저장합니다.
- Recalling a Memory Preset: Simply press the corresponding preset number button (1, 2, 3, 또는 4) to automatically adjust the desk to the saved height.
- 책상 재설정: If the desk encounters an error or needs to be recalibrated:
- 를 누르세요 아래로(▼) button to bring the table to its lowest height.
- 계속해서 유지하다 아래로(▼) 버튼을 5초 until the desk resets.
- Unlocking the Desk: If the desk becomes locked, press the S 버튼과 아래로(▼) button simultaneously for 5초.
6. 유지관리
Regular maintenance ensures the longevity and optimal performance of your UNICOO Electric Standing Desk.
- 청소: 부드러운 천으로 테이블 상판과 프레임을 닦으세요.amp 천으로 닦으세요. 마감재를 손상시킬 수 있는 연마성 세제나 강한 화학 물질은 피하세요.
- 케이블 관리 : 케이블이 엉키거나 손상되는 것을 방지하기 위해 정기적으로 점검하고 정리하십시오.
- 나사 조임 정도: Occasionally check all screws and fasteners to ensure they remain tight. Re-tighten if necessary.
- 모터 및 메커니즘: The motor and lifting mechanisms are designed for durability. Avoid obstructing the movement of the desk.
7. 문제 해결
If you encounter issues with your UNICOO Electric Standing Desk, refer to the following common solutions:
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 책상이 움직이지 않음 / 전원 없음 | Power cable disconnected, power outlet issue, motor malfunction. | Check power cable connection to the desk and wall outlet. Ensure the outlet is functional. |
| Desk stops moving / Error message (e.g., "ASt") | Overload, obstruction, sensor error, motor synchronization issue. | Remove any excess weight or obstructions. Perform a reset: Press the 아래로(▼) button to the lowest height, then hold for 5 seconds. If an "ASt" error persists, gently wiggle the right side of the desk or check the drive rod connection to the motor. |
| Desk is locked | Accidental lock activation. | 를 누르세요 S 버튼과 아래로(▼) button simultaneously for 5 seconds to unlock. |
| 고르지 못한 높이 조정 | Motor synchronization issue, uneven weight distribution. | Perform a desk reset. Ensure weight is evenly distributed on the tabletop. |
If these steps do not resolve the issue, please contact UNICOO customer support for further assistance.
8. 사양
| 특징 | 세부 사항 |
|---|---|
| 모델 번호 | KT1001 |
| 상표 | UNICOO |
| 제품 크기(D x W x H) | 23.6인치 x 46.5인치 x 30.5인치 |
| 최소 높이 | 30 인치 |
| 최대 높이 | 48 인치 |
| 최대 중량 용량 | 225 파운드 |
| 품목 무게 | 60 파운드 |
| 상단 소재 | 엔지니어드 우드(적층목재) |
| 기본 소재 | 합금강 |
| 특별 기능 | Adjustable Height, Electric, LED Memory Control |
Image: Diagram illustrating the dimensions of the UNICOO standing desk, including its 23.6-inch depth, 46.5-inch width, and adjustable height range from 30.5 to 48 inches.
9. 보증 및 지원
Your UNICOO Electric Height Adjustable Standing Desk KT1001 is covered by a 2년 보증 for the frame, motor, and other mechanisms.
For warranty claims, technical support, or any questions not addressed in this manual, please contact UNICOO customer service. Refer to your purchase documentation for specific contact details or visit the official UNICOO web대지.