Jectse 5V 60MM Hand Wheel Pulse Encoder User Manual

1. 서론

This manual provides essential information for the safe and effective use of the Jectse 5V 60MM Hand Wheel Pulse Encoder. This device is designed for manual pulse input in various CNC (Computer Numerical Control) systems, including lathes, grinding machines, milling machines, and engraving machines. Please read this manual thoroughly before installation and operation.

2. 안전 정보

부상 및 장비 손상을 방지하기 위해 다음 안전 수칙을 준수하십시오.

• 전원 공급 장치가 지정된 볼륨과 일치하는지 확인하십시오.tage (5V) before connecting the encoder.
• 인코더를 과도한 습기, 먼지 또는 극한 온도에 노출시키지 마십시오.
• Avoid applying excessive force to the hand wheel or terminals.
• All electrical connections should be performed by qualified personnel.
• Disconnect power to the CNC system before installing or removing the encoder.

3. 제품 오버view

The Jectse 5V 60MM Hand Wheel Pulse Encoder is a robust and precise input device. It features a 60mm diameter hand wheel with 100 distinct stop positions, providing tactile feedback for accurate manual control. The encoder is constructed from high-grade aviation aluminum for durability.

The encoder is designed for smooth rotation without sticking points, ensuring reliable operation. Its compact and lightweight design facilitates easy integration into various control panels.

4. 사양

5. 설정 및 설치

Follow these steps to properly install your hand wheel pulse encoder:

1. 장착 위치 준비: Choose a stable and accessible location on your CNC control panel. Ensure there is enough space for the encoder and its wiring.
2. Secure the Encoder: Mount the encoder using the provided fasteners. Ensure it is firmly attached to prevent movement during operation.
3. 배선 연결: The encoder uses a 6mm terminal connection. Refer to the wiring diagram below and your CNC system's documentation for correct connections. Typically, the terminals are labeled for power (VCC, 0V) and signal outputs (A, B).

• VCC: 5V DC 전원 공급 장치에 연결합니다.
• 0V : Connect to the ground (GND) of the power supply.
• A: Connect to the A-phase input of your CNC controller.
• B: Connect to the B-phase input of your CNC controller.

Ensure all connections are secure and correctly polarized to avoid damage to the encoder or the CNC system.

6. 사용 설명서

Once installed and powered, the hand wheel pulse encoder provides manual control input to your CNC system:

• Axis Selection: Depending on your CNC controller, you may need to select the desired axis (X, Y, Z, etc.) before using the hand wheel. Refer to your CNC system's manual for axis selection procedures.
• 움직임 제어: Rotate the hand wheel clockwise or counter-clockwise to generate pulses. These pulses are interpreted by the CNC controller to move the selected axis. The 100 stop positions provide precise, incremental movement control.
• Speed/Increment Adjustment: Some CNC systems allow adjustment of the movement increment per pulse (e.g., 0.001mm, 0.01mm, 0.1mm). Adjust this setting on your CNC controller as needed for fine or coarse adjustments.
• 원활한 작동: The encoder is designed for smooth rotation. If you experience any resistance or sticking, refer to the Troubleshooting section.

7. 유지관리

The Jectse Hand Wheel Pulse Encoder requires minimal maintenance:

• 청소: Periodically wipe the exterior of the encoder with a soft, dry cloth to remove dust and debris. Do not use abrasive cleaners or solvents.
• 점검: Regularly check the wiring connections for looseness or damage. Ensure the mounting is secure.
• 환경 보호: Keep the encoder in a clean, dry environment, free from excessive vibrations and electromagnetic interference.

8. 문제 해결

Problem: Encoder does not respond.

해결책:

• Check all wiring connections to ensure they are secure and correctly connected to the CNC controller.
• Verify that the encoder is receiving the correct 5V power supply.
• Ensure the CNC controller is configured to accept input from the external hand wheel.

Problem: Movement is erratic or inconsistent.

해결책:

• Inspect wiring for any loose connections or damaged insulation that could cause signal interference.
• Check for any physical obstructions preventing smooth rotation of the hand wheel.
• Ensure the encoder is securely mounted and not vibrating.

Problem: Hand wheel feels stiff or sticky.

해결책:

• Clean the exterior of the encoder to remove any accumulated dust or debris that might impede rotation.
• Ensure no foreign objects have entered the mechanism. Do not attempt to lubricate internal components unless specifically instructed by the manufacturer.

9. 보증 및 지원

Jectse products are manufactured to high-quality standards. For warranty information or technical support, please refer to the documentation provided with your purchase or contact your vendor. Keep your purchase receipt for warranty claims.