1. 제품 오버view
The Einhell TC-TC 800 Tile Cutter is designed for precise and efficient cutting of wall and floor tiles. This robust tool is suitable for various home renovation projects, offering clean cuts with minimal dust thanks to its water cooling system.
주요 특징:
- Robust Stainless Steel Table: Measuring 395 x 385 mm, it is easy to clean and features an angular scale up to 45° with non-slip feet for stable operation.
- Precise Cutting Guide: Ensures exact and straight cuts. The angle stop is adjustable from -45° to +45° for miter cuts.
- Integrated Water Reservoir: Provides necessary water cooling for the saw blade, protecting it from heat damage.
- 절단 용량: Maximum cutting height of 14 mm at 45° and 34 mm at 90°.
- 안전 가드: A protective guard for the cutting disc ensures user safety from chips and dust.
2. 안전 지침
이 전동 공구와 함께 제공되는 모든 안전 경고, 지침, 그림 및 사양을 항상 읽고 이해하십시오. 아래 나열된 모든 지침을 따르지 않으면 감전, 화재 및/또는 심각한 부상이 발생할 수 있습니다.
일반 안전 경고:
- 안전 안경, 귀 보호구, 장갑 등 적절한 개인 보호 장비(PPE)를 착용하십시오.
- 작업 공간이 깨끗하고, 조명이 밝으며, 방해물이 없는지 확인하세요.
- 공구를 작동하는 동안 어린이와 구경꾼이 접근하지 못하도록 하십시오.
- Never operate the tool if the power cord or plug is damaged.
- Always disconnect the power supply before making any adjustments, changing accessories, or performing maintenance.
- 절단할 재료에 맞는 칼날을 사용하십시오.
- Ensure the water reservoir is adequately filled before operation to prevent overheating of the blade.
3. 구성 요소 이상view
Familiarize yourself with the main components of your Einhell TC-TC 800 Tile Cutter:
- Cutting Table (Stainless Steel)
- Diamond Cutting Disc (180 mm diameter)
- 모터 유닛
- 물 저장고
- Cutting Guide with Scale
- Angle Stop (-45° to +45°)
- 블레이드 가드
- 켜기/끄기 스위치
- 운반 손잡이
그림 1: 이상view of the Einhell TC-TC 800 Tile Cutter with its main parts.
4. 설정
Before operating the tile cutter, ensure proper setup for safety and optimal performance.
4.1 풀기 및 검사
- 포장에서 모든 구성 요소를 조심스럽게 제거합니다.
- Inspect the tool for any signs of damage during transit. Do not operate if damaged.
- 나열된 모든 구성 요소가 있는지 확인하세요.
4.2 물 저장고 채우기
The integrated water reservoir is essential for cooling the diamond cutting disc and reducing dust.
- Locate the water reservoir beneath the cutting table.
- Fill the reservoir with clean water to the indicated level. Ensure the water pump is submerged.
- Regularly check the water level during operation and refill as needed.
Figure 2: Filling the water reservoir for wet cutting.
4.3 Adjusting the Cutting Guide and Angle Stop
For accurate cuts, adjust the cutting guide and angle stop as required.
- The cutting guide with scale ensures straight cuts. Position it according to your desired measurement.
- For miter cuts, adjust the angle stop between -45° and +45°. Secure it firmly before cutting.
Figure 3: Adjustable angle stop for miter cuts.
5. 사용 설명서
Follow these steps for safe and effective tile cutting.
5.1 전원 켜기/끄기
- Connect the tile cutter to a suitable power outlet (240 Volts).
- To turn on, press the green 'ON' button.
- To turn off, press the red 'OFF' button.
Figure 4: Power switch for turning the machine on and off.
5.2 절단하기
- Place the tile firmly on the stainless steel cutting table, aligning it with the cutting guide or angle stop as desired.
- Ensure the water pump is active and water is flowing to the blade.
- Turn on the tile cutter.
- Slowly and steadily push the tile through the rotating diamond blade. Avoid excessive force.
- Once the cut is complete, turn off the tile cutter and wait for the blade to stop before removing the tile.
Figure 5: Demonstrating a tile being cut with the machine.
5.3 공식 제품 비디오: 사용 방법
Video 1: This video demonstrates the basic operation and usage of a tile cutter, including setup and cutting techniques.
6. 유지관리
Regular maintenance ensures the longevity and performance of your tile cutter.
6.1 물탱크 청소
After each use, clean the water reservoir to prevent buildup of tile dust and debris.
- 전원공급장치를 분리하세요.
- Remove the cutting table or access panel to reach the reservoir.
- Empty the dirty water and thoroughly clean the reservoir with fresh water.
- 구성품을 재 조립하십시오.
6.2 블레이드 교체
Replace the diamond cutting disc when it becomes dull or damaged.
- 도구의 전원 플러그가 뽑혀 있는지 확인하십시오.
- Use the provided tool to loosen the blade retaining nut.
- Carefully remove the old blade and install the new 180 mm diamond cutting disc, ensuring it is correctly oriented.
- 고정 너트를 단단히 조이십시오.
7. 문제 해결
This section addresses common issues you might encounter with your tile cutter.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Poor cut quality (chipping, uneven edges) | Dull or incorrect blade; insufficient water cooling; pushing too fast. | Replace blade with a suitable diamond disc; ensure water reservoir is full and pump is working; reduce feeding speed. |
| Water overflow from table | Water channels blocked; reservoir too full; uneven surface. | Clean water channels; do not overfill reservoir; ensure the machine is on a level surface. |
| 기계가 시작되지 않습니다 | 전원 공급 안 됨; 스위치 불량; 모터 문제. | Check power connection and circuit breaker; test the power outlet; contact customer support if switch or motor is faulty. |
| Rusted screws/components | Lack of proper drying/maintenance after wet use. | Regularly clean and dry all metal components after use. Apply a rust preventative lubricant (e.g., WD-40) to screws and moving parts. |
8. 사양
| 특징 | 세부 사항 |
|---|---|
| 상표 | 아인헬 |
| 모델 번호 | 4301185 |
| 힘 | 800 와트 |
| 권tage | 240 볼트 |
| 속도 | 2950 RPM |
| Diamond Cutting Disc Diameter | 180mm (XNUMXmm) |
| 최대 절단 높이(90°) | 34mm (XNUMXmm) |
| 최대 절단 높이(45°) | 14mm (XNUMXmm) |
| Angle of Cut | 45도 |
| 테이블 크기 (길이 x 너비) | 39.6cm x 38.5cm |
| 제품 크기(L x W x H) | 39.6l. x 38.5an. x 25.5al. centimeters |
| 제품 무게 | 9.1 킬로그램 |
| 전원 | 전원 코드 포함 전기 |
| 특별 기능 | Adjustable angle stop, parallel stop with scale |
9. 보증 및 지원
9.1 보증 정보
This Einhell product comes with a 2년 한정 보증보증 청구를 위해 구매 증빙 서류를 보관하세요.
9.2 고객 지원
For technical assistance, spare parts, or warranty inquiries, please contact Einhell customer service. Refer to the official Einhell web최신 연락처 정보는 해당 사이트나 제품 포장에서 확인하세요.