Universal Office Chair Assembly Manual

1. 중요한 안전 정보

조립 및 사용 전에 모든 지침을 주의 깊게 읽어 주십시오. 나중에 참조할 수 있도록 이 설명서를 보관하십시오.

• 조립을 시작하기 전에 모든 부품이 있는지, 손상되지 않았는지 확인하십시오. 부품이 누락되었거나 손상된 경우 사용하지 마십시오.
• Assemble the chair on a soft, clean surface to prevent scratching.
• 조립하는 동안 나사를 너무 세게 조이지 마세요. 부품이 손상될 수 있습니다.
• 어린이와 애완동물이 조립 구역에 접근하지 못하도록 하세요. 작은 부품은 질식 위험을 초래할 수 있습니다.
• Only use the chair for its intended purpose.
• 의자 위에 서지 마세요.

2. 패키지 내용

Verify that all components listed below are included in your package.

3. 조립 설명서

Follow these steps carefully to assemble your office chair.

1. 스타베이스에 캐스터 부착: Insert each caster (F) into the holes at the end of each leg of the star base (E). Push firmly until they click into place.
2. 가스 리프트 삽입: Place the gas lift cylinder (D) into the center hole of the assembled star base (E). Ensure it sits securely.
3. 좌석에 메커니즘 플레이트 부착: Align the mechanism plate (G) with the pre-drilled holes on the underside of the seat cushion (B). Ensure the front of the mechanism plate faces the front of the seat. Secure with four M8x25mm screws (I) using the Allen wrench (J).
4. 좌석에 팔걸이 부착: Attach the armrests (C) to the underside of the seat cushion (B) using four M6x20mm screws (H), two per armrest. Do not fully tighten yet.
5. Attach Chair Back to Armrests: Align the chair back (A) with the remaining holes on the armrests (C). Secure with the remaining four M6x20mm screws (H), two per armrest. Now, fully tighten all armrest screws.
6. 시트 어셈블리를 가스 리프트에 연결하십시오: Carefully place the assembled seat and back onto the gas lift cylinder (D) protruding from the star base. Press down firmly to secure.

Your office chair is now assembled.

4. 사용 설명서

Familiarize yourself with the chair's adjustment features for optimal comfort.

• 높이 조정: To raise the seat, lift the lever located under the right side of the seat while taking your weight off the chair. To lower the seat, lift the lever while seated. Release the lever at the desired height.
• 기울기 잠금/해제: Pull the same lever outwards to unlock the tilt function, allowing the chair back to recline. Push the lever inwards to lock the chair back in an upright position.
• 틸트 장력: Rotate the round knob located under the front-center of the seat to adjust the tension of the tilt mechanism. Turn clockwise to increase tension (making it harder to recline) and counter-clockwise to decrease tension (making it easier to recline).
• Armrest Adjustment (if applicable): Some models feature adjustable armrests. Look for buttons or levers on the armrests to adjust their height or pivot.

5. 유지관리

Regular maintenance will prolong the life of your office chair.

• 청소: 부드러운 d로 표면을 닦으십시오.amp cloth. For fabric upholstery, use a mild fabric cleaner. Avoid harsh chemicals or abrasive cleaners.
• 패스너 점검: 모든 나사와 볼트가 단단히 조여져 있는지 정기적으로 점검하세요. 필요하면 다시 조이세요.
• 캐스터 청소: Remove any hair or debris that may accumulate around the casters to ensure smooth movement.
• 매끄럽게 하기: The gas lift cylinder is maintenance-free. Do not attempt to lubricate it.

6. 문제 해결

일반적인 문제에 대한 해결책은 이 섹션을 참조하세요.

7. 사양

Key technical details of your office chair.