소개
The Flysky FS-GR3E is a reliable 3-channel 2.4GHz receiver designed for use with RC cars and boats. It utilizes Flysky's Automatic Frequency Hopping Digital System (AFHDS) technology to provide a stable and interference-free connection. This receiver is compatible with various Flysky transmitters, including the FS-GT2, FS-GT2B, FS-GT3B, and FS-GT3C. This manual provides essential information for the proper setup, operation, and maintenance of your FS-GR3E receiver.
영상: The Flysky FS-GR3E 3-Channel 2.4GHz Receiver. This image displays the compact black receiver unit with its antenna wire and various ports for connection to servos, ESC, and power.
안전 정보
Please read and understand the following safety guidelines before operating your receiver:
- Ensure correct polarity when connecting power to the receiver. Incorrect connections can cause damage.
- Operate your RC model in open areas, away from people, vehicles, and obstacles.
- Avoid exposing the receiver to moisture, extreme temperatures, or direct sunlight for extended periods.
- Always turn on your transmitter first, then the receiver. When powering off, turn off the receiver first, then the transmitter.
- Regularly inspect all wiring and connections for damage or loose contacts.
패키지 내용
패키지에 모든 품목이 들어 있는지 확인하세요.
- 1 x Flysky FS-GR3E 2.4GHz 3-Channel Receiver
명세서
| 채널 | 3 |
| 모델 유형 | 자동차 / 보트 |
| RF 수신기 감도 | -105dbm |
| 조정 | GFSK |
| 시스템 유형 | AFHDS |
| 감광도 | 1024 |
| 안전장치 | Yes (Channel 2) |
| 바인딩 포트 | Yes (Channel 3) |
| 전원 포트 | 예 (VCC) |
| 전원 입력 | 4-11V DC |
| 무게 | 5g(약 0.18온스) |
| 안테나 길이 | 26mm |
| 치수(길이*너비*높이) | 37.6 x 22.3 x 13mm(약 1.48 x 0.88 x 0.51인치) |
| 색상 | 검은색 |
설정
1. 설치
Mount the FS-GR3E receiver securely in your RC model, ensuring it is protected from vibrations and moisture. Position the antenna wire as straight as possible and away from metal parts or carbon fiber chassis to maximize range and signal quality. Connect your Electronic Speed Controller (ESC) to Channel 2 (throttle), and your steering servo to Channel 1. If using a third channel for auxiliary functions, connect it to Channel 3.
2. 수신기와 송신기 연결
The receiver must be bound to your Flysky transmitter before use. Follow these steps:
- 송신기의 전원이 꺼져 있는지 확인하세요.
- Insert the bind plug (usually included with your transmitter or receiver) into the "BIND" port (Channel 3) on the FS-GR3E receiver.
- Connect power to the receiver (e.g., via the ESC or a separate battery pack connected to the VCC port). The receiver's LED should start flashing rapidly, indicating it is in binding mode.
- While holding the bind button on your transmitter (or following its specific binding procedure), power on the transmitter.
- 수신기의 LED가 깜빡임을 멈추고 계속 켜져 있으면 바인딩이 성공적으로 완료된 것입니다.
- 수신기를 끄고 나서 송신기를 끄십시오.
- 수신기에서 바인드 플러그를 제거합니다.
- Power on the transmitter first, then the receiver. Verify that the receiver's LED is solid and that the controls respond correctly.
Note: If binding fails, repeat the steps. Some transmitters may have slightly different binding procedures; refer to your transmitter's manual for specific instructions.
운영
1. Failsafe Function
The FS-GR3E receiver features a failsafe function on Channel 2 (throttle) to prevent runaway models in case of signal loss. To set the failsafe position:
- Ensure the receiver is bound to the transmitter and both are powered on.
- Position the throttle stick on your transmitter to the desired failsafe position (e.g., neutral or brake).
- Locate the small failsafe button on the receiver. Press and hold this button until the receiver's LED blinks once, then release.
- The failsafe position is now set. To test, power on the transmitter and receiver, then turn off the transmitter. The throttle should move to the set failsafe position.
It is recommended to set the failsafe to a neutral or brake position for safety.
2. Channel Assignment
The FS-GR3E receiver has 3 channels. Standard assignments are:
- 채널 1 : Steering (for RC cars/boats)
- 채널 2 : Throttle (for RC cars/boats)
- 채널 3 : Auxiliary function (e.g., lights, gear shift, or used as Bind port)
유지
To ensure the longevity and optimal performance of your FS-GR3E receiver, follow these maintenance tips:
- Keep the receiver clean and free from dust, dirt, and debris. Use a soft, dry brush or compressed air for cleaning.
- Avoid exposing the receiver to water or excessive humidity. If it gets wet, disconnect power immediately and allow it to dry completely before re-use.
- Store the receiver in a cool, dry place when not in use.
- Regularly check the antenna wire for any cuts, kinks, or damage. A damaged antenna can significantly reduce range.
- Ensure all connections to the receiver are secure and free from corrosion.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 바인딩 시도 후 수신기 LED가 계속 켜져 있지 않습니다. | Binding procedure not followed correctly; transmitter not in bind mode; bind plug not inserted correctly; power issue. | Repeat binding steps carefully. Ensure bind plug is fully inserted into Channel 3. Check power supply to receiver. Refer to transmitter manual for its specific binding process. |
| 모델로부터 응답이 없습니다. | Receiver not bound; transmitter off; low battery in transmitter or model; incorrect wiring; damaged receiver/servo/ESC. | Verify receiver is bound (solid LED). Ensure transmitter is on. Check battery levels. Inspect all wiring connections. Test components individually if possible. |
| 수신 범위가 제한적이거나 신호가 불안정합니다. | Antenna obstructed or damaged; interference; receiver mounted too close to metal/carbon fiber. | Ensure antenna is straight and clear of obstructions. Check for local interference sources. Relocate receiver if necessary. Inspect antenna wire for damage. |
| Failsafe not working. | Failsafe not set correctly; signal loss not detected. | Re-set the failsafe position following the instructions in the "Operating" section. Ensure the transmitter is turned off to test signal loss. |
보증 및 지원
For warranty information and technical support, please refer to the official Flysky web웹사이트를 방문하거나 공인 Flysky 대리점에 문의하십시오. 구매 영수증을 보관하여 구매 증빙 자료로 활용하십시오.