소개
This manual provides detailed instructions for the assembly, use, and maintenance of your Powell Heavy Metal Twin-Over-Twin Bunk Bed. Please read all instructions carefully before assembly and retain this manual for future reference. The bunk bed is designed for durability and versatility, offering two twin-sized sleeping spaces within a compact footprint, or convertible into two separate twin beds.
Figure 1: Assembled Powell Heavy Metal Twin-Over-Twin Bunk Bed.
중요한 안전 정보
경고: 끼임이나 낙상으로 인한 심각하거나 치명적인 부상을 방지하려면 다음과 같이 하십시오.
- 상단 벙크 엔드 구조물과 상자에 표시된 경고 정보를 따르십시오. 침대에서 경고 라벨을 제거하지 마십시오.
- Never allow a child under 6 years old on the upper bunk.
- 항상 권장 크기의 매트리스나 매트리스 지지대 또는 둘 다를 사용하여 갇히거나 넘어질 가능성을 방지하십시오.
- Use only a mattress which is 74"- 75" long and 37-1/2"- 38-1/2" wide on the bunk.
- Ensure thickness of mattress does not exceed 8" and surface of mattress is at least 5" below upper edge of guardrails.
- 항상 상단 침대의 긴 양쪽에 난간을 사용하십시오.
- If bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and the wall.
- Prohibit horseplay on or under bed(s) and prohibit jumping on the bed.
- 위층 침대에 두 명 이상의 사람을 금지하십시오.
- 위층 침대에 오르내릴 때는 사다리를 이용하세요.
- Maximum total weight is not to exceed 300 lbs. on the upper bunk.
- 가드레일, 사다리 및 기타 구성 요소가 적절한 위치에 있고 손상되지 않았는지, 모든 커넥터가 단단히 조여져 있는지 주기적으로 확인하고 확인하십시오.
- Do not use substitute parts. Replacement parts, including additional guardrails, may be obtained from our customer service department.
- Use of water or sleep flotation mattresses is prohibited.
- 야간 조명을 사용하면 이층 침대를 사용하는 어린이에게 추가적인 안전 예방 조치를 제공할 수 있습니다.
목졸림 위험: 침대와 함께 사용하도록 설계되지 않은 이층 침대의 어떤 부분에도 물건을 부착하거나 걸지 마십시오. 예를 들어amp고리, 벨트, 줄넘기 등을 포함하나 이에 국한되지 않습니다.
DO NOT REMOVE THIS LABEL. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
구성품 목록
Before beginning assembly, ensure all parts are present and undamaged. Refer to the diagram below for identification.
Figure 2: Assembled bunk bed for component reference. Individual parts are detailed in assembly steps.
- Upper Panels (2)
- Lower Panels (2)
- Lower Bed Frame (1)
- Upper Bed Frame (1)
- Guardrails (2)
- Ladder (1)
- Connection Posts (4)
- 모자 (8)
Hardware (screws, washers, nuts, Allen wrench) will be included in a separate package. Please verify all hardware is present before starting assembly.
설치 지침
Assembly requires at least two adults. Do not overtighten screws during initial assembly; tighten all fasteners securely once the bed is fully assembled.
Step 1: Assemble the Lower Bed Frame
Attach the Lower Panels (B) to the Lower Bed Frame (C) using the provided bolts, washers, and nuts (L+K+J). Ensure all connections are secure but do not fully tighten yet. Use the Allen wrench (M).
Figure 3: Step 1 - Assembling the lower bed frame.
Step 2: Attach Connection Posts
Insert the four Connection Posts (G) into the top of the posts of the assembled Lower Bed Frame (B).
Figure 4: Step 2 - Attaching connection posts.
Step 3: Attach Upper Panels
Place the Upper Panels (A) onto the Connection Posts (G) on the Lower Bed Frame. Ensure they are seated correctly.
Figure 5: Step 3 - Attaching upper panels.
Step 4: Assemble the Upper Bed Frame
Attach the Upper Bed Frame (D) to the Upper Panels (A) using the remaining bolts, washers, and nuts (L+K+J). Fully tighten all fasteners from Step 1 and Step 4 now. Use the Allen wrench (M).
Figure 6: Step 4 - Assembling the upper bed frame.
Step 5: Install Guardrails and Ladder
Attach the Guardrails (E) to the Upper Panels (A) using the designated screws (I) and the Allen wrench (M). Ensure they are securely fastened on both long sides of the upper bunk. Hook the Ladder (F) onto the side of the Upper Bed Frame (D). Ensure the hooks are fully engaged and the ladder is stable. Some models may include additional fasteners (H) to secure the ladder to the upper bed frame (D) using screws (M). Refer to the detailed diagram for proper placement and tightening with the Allen wrench (O).
Figure 7: Steps 5-7 - Installing guardrails and attaching/securing the ladder.
6단계: 캡 설치
Place the plastic Caps (N) onto any exposed posts for a finished look and added safety.
Figure 8: Step 8 - Installing caps.
Conversion to Two Free-Standing Beds
Your bunk bed can be converted into two separate twin beds. Follow these instructions carefully:
- Remove the Ladder (F) and Guardrails (E).
- Carefully lift the Upper Bed Frame (D) off the Connection Posts (G).
- Remove the Connection Posts (G) from the Lower Bed Frame (B).
- Attach the Upper Panels (A) to the Upper Bed Frame (D) using the appropriate hardware (L+K+J) to form the second twin bed.
- Install Caps (N) on any exposed posts of both new twin beds.
Figure 9: Diagram illustrating the conversion of the bunk bed into two separate twin beds.
Figure 10: The Powell Heavy Metal Twin-Over-Twin Bunk Bed configured as two individual twin beds.
유지
- Regularly inspect all bolts and connections to ensure they remain tight. Retighten as necessary to maintain structural integrity.
- Clean the metal surfaces with a soft, damp cloth. Avoid abrasive cleaners or harsh chemicals that could damage the pewter powder-coated finish.
- Check the ladder for any signs of wear or damage. Replace any worn or broken parts immediately.
- Ensure mattresses meet the recommended dimensions and thickness to maintain safety standards.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 침대가 흔들리거나 불안정합니다. | 느슨한 패스너. | Check and tighten all bolts and screws. Ensure all connection posts are fully seated. |
| Ladder is not secure. | Ladder hooks not fully engaged or securing screws loose. | Ensure ladder hooks are properly seated over the upper bed frame. Tighten any securing screws if present. |
| Parts missing or damaged. | 배송 중 손상 또는 포장 오류. | Contact customer support for replacement parts. Do not attempt to use damaged components. |
명세서
- 모델 번호: 941-138
- 크기: Twin-Over-Twin
- 제품 크기: 79.33인치 길이 x 43인치 너비 x 65인치 높이
- 색상: 땜납
- 재료: Heavy Gauge Tubular Steel
- 마감 유형 : 파우더 코팅
- Maximum Weight Recommendation (Upper Bunk): 300파운드
- 호환 매트리스 크기: Twin (74"-75"L x 37-1/2"-38-1/2"W)
- Maximum Mattress Thickness (Upper Bunk): 8"
- 필요한 조립: 예
- 품목 무게: 109.8파운드
그림 11: 제품 치수
보증 및 지원
보증 정보: This product is covered by a limited manufacturer's warranty against defects in materials and workmanship. For specific warranty details and duration, please refer to the product's original purchase documentation or contact Powell customer service. Keep your proof of purchase for warranty claims.
고객 지원: If you have any questions regarding assembly, missing parts, or product operation, please contact Powell customer service. Contact information can typically be found on the product packaging or the retailer's web제품을 구매한 사이트.
교체 부품: For replacement parts, including additional guardrails, please contact our customer service department. Do not use substitute parts not approved by the manufacturer.