DigiTech IPB10

DigiTech IPB10 Guitar Floor Multi-Effects Pedal User Manual

모델: IPB10

1. 서론

The DigiTech IPB10 is an advanced programmable guitar floor multi-effects pedalboard designed to provide guitarists with extensive control over their sound. It integrates with an Apple iPad (not included) to offer a visual and intuitive interface for creating, editing, and managing a wide array of guitar effects, amplifiers, and cabinets. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your IPB10 unit.

2. 중요한 안전 정보

  • 전원 공급 장치: Use only the specified power adapter. Using an incorrect adapter can damage the unit and void your warranty.
  • 통풍: 장치 주변의 환기가 잘 되도록 하세요. 환기구를 막지 마세요.
  • 물과 습기: Do not expose the unit to water, rain, or excessive moisture.
  • 서비스: 제품을 직접 수리하려고 하지 마십시오. 모든 수리는 자격을 갖춘 서비스 담당자에게 맡기십시오.
  • 놓기: 제품이 넘어지는 사고를 방지하기 위해 안정적이고 평평한 곳에 놓으십시오.

3. 패키지 내용

귀하의 패키지에 다음 품목이 포함되어 있는지 확인하세요.

  • DigiTech IPB10 Guitar Floor Multi-Effects Pedalboard
  • 전원 어댑터
  • USB Cable (for firmware updates)
  • 빠른 시작 가이드(이 디지털 매뉴얼에는 포함되지 않음)

Note: An Apple iPad is required for full functionality and is not included with the IPB10.

4. 설정

4.1 물리적 연결

  1. 기타 커넥트: 기타를 기타 입력 jack on the IPB10.
  2. 연결하기 Amp리파이어/믹서: 연결하다 출력 of the IPB10 to your guitar amplifier, mixer, or audio interface. Use appropriate cables (e.g., 1/4-inch instrument cables).
  3. 전원 연결: Plug the supplied power adapter into the 전원 입력 on the IPB10, then into a suitable AC outlet.
  4. iPad를 삽입하세요: Carefully place your compatible iPad into the designated dock on the IPB10. Ensure the 30-pin connector aligns correctly.

    중요 참고 사항: The IPB10 features a 30-pin connector for iPad integration. Newer iPad models with Lightning connectors will require a 30-pin to Lightning adapter. Due to the physical design of the IPB10's dock, some adapters may not fit properly. An extension cable for the Lightning connector might be necessary for newer iPads. The iPad is primarily used for configuration; the IPB10 can operate independently once programmed.

4.2 소프트웨어 설치 및 펌웨어 업데이트

  1. Install iPB-10 App: Download and install the official DigiTech iPB-10 app from the Apple App Store onto your iPad.
  2. 펌웨어 업데이트 확인: Connect the IPB10 to your computer using the supplied USB cable. Visit the DigiTech support website to download the latest firmware update utility and instructions for your IPB10. It is crucial to perform firmware updates as recommended for optimal performance and compatibility.

5. 사용 설명서

DigiTech IPB10 Guitar Floor Multi-Effects Pedal with iPad dock, footswitches, and expression pedal

그림 1: 위에view of the DigiTech IPB10 Guitar Floor Multi-Effects Pedal. This image displays the entire pedalboard, including the central iPad dock, the five footswitches labeled A through E on the upper row, the five footswitches labeled 1 through 5 on the lower row, the STOMP and AMP toggle switches, the UP and DOWN bank switches, and the integrated expression pedal on the right. The iPad screen shows a graphical representation of various effects pedals.

5.1 전원 켜기 및 초기 사용

Once all connections are made and the iPad is docked, power on the IPB10. The iPad app should automatically detect the pedalboard.

5.2 Understanding the Interface

  • iPad Display: The iPad serves as the primary visual interface, allowing you to drag and drop effects, adjust parameters, and manage presets.
    Close-up of DigiTech IPB10 iPad display showing virtual effects pedals

    그림 2: Detail of the iPad display area on the IPB10. The screen shows a graphical user interface with virtual stompboxes (e.g., Overdrive, Delay, Reverb) arranged in a signal chain, along with controls for amp and cabinet simulation. This is where users interact with the software to design their pedalboards.

  • Footswitches (A-E, 1-5): These ten footswitches allow you to activate/deactivate individual effects or recall specific presets. Their function is assigned within the iPB-10 app.
    Close-up of DigiTech IPB10 footswitches A, B, 1, 2

    그림 3: Detail of the lower-left footswitches on the IPB10. This image highlights footswitches A and B from the upper row, and footswitches 1 and 2 from the lower row. Each footswitch has an associated LED indicator. These are used for engaging effects or selecting presets.

  • STOMP/AMP 토글 스위치: These dedicated switches allow for quick toggling of stompbox effects and amp라이저 모델.
    Close-up of DigiTech IPB10 STOMP and AMP 토글 스위치

    그림 4: Detail of the STOMP and AMP toggle switches located on the upper-left side of the IPB10. These switches provide direct control over the stompbox and amplifier sections of the virtual pedalboard.

  • UP/DOWN Bank Switches: Use these switches to navigate through different banks of presets.
    Close-up of DigiTech IPB10 UP and DOWN bank switches

    그림 5: Detail of the UP and DOWN bank switches on the upper-right side of the IPB10. These switches are used to scroll through different banks of stored presets, allowing access to a wider range of sounds during live performance.

  • 익스프레션 페달: The integrated expression pedal can be assigned to control various effect parameters (e.g., Wah, Volume, Delay feedback) within the iPB-10 app.
    Close-up of DigiTech IPB10 expression pedal

    그림 6: Detail of the integrated expression pedal on the right side of the IPB10. The pedal features a textured metal surface with black rubber grips and the DigiTech logo. This pedal provides real-time control over various effect parameters.

5.3 Creating and Editing Pedalboards

The iPB-10 app allows you to design custom pedalboards by dragging and dropping up to 10 different pedals, an amplifier, and a cabinet into your signal chain.

  • Select Effects: Browse the library of 87 pedals, 54 amps, and 26 cabinets.
  • Arrange Signal Chain: Drag and drop components to arrange them in any desired order.
  • 매개변수 조정: Tap on any virtual pedal, amp, or cabinet to access and adjust its parameters (knobs, switches) directly on the iPad screen.
  • Assign Footswitches: Assign specific effects or entire pedalboard configurations to the physical footswitches for quick access during performance.

5.4 프리셋 저장 및 불러오기

The IPB10 allows you to save an infinite number of custom pedalboard configurations as presets within the app. 100 of these presets can be made accessible via the footswitches.

  • 사전 설정 저장 : Use the app's interface to save your current pedalboard configuration.
  • 프리셋 불러오기: Use the UP/DOWN bank switches and the A-E/1-5 footswitches to recall saved presets.

6. 유지관리

  • 청소: Use a soft, dry cloth to clean the exterior of the IPB10. Do not use abrasive cleaners or solvents.
  • 소프트웨어 업데이트: DigiTech를 정기적으로 확인하세요 website and the Apple App Store for updates to the IPB10 firmware and the iPB-10 app. Keeping your software updated ensures optimal performance and access to new features or bug fixes.
  • 저장: When not in use for extended periods, store the IPB10 in a cool, dry place, away from direct sunlight and extreme temperatures.

7. 문제 해결

문제가능한 원인해결책
소리가 출력되지 않습니다.
  • 잘못된 케이블 연결.
  • 볼륨 레벨이 너무 낮습니다.
  • Effects bypassed or turned off.
  • 모든 오디오 케이블이 올바른 입력/출력 단자에 제대로 연결되어 있는지 확인하십시오.
  • Check the volume settings on the IPB10, your guitar, and your amp정수기/믹서.
  • Ensure effects are engaged within the iPB-10 app.
iPad not connecting or app not recognizing IPB10.
  • iPad not properly seated in the dock.
  • Incompatible iPad model or adapter issue.
  • Outdated iPB-10 app or IPB10 firmware.
  • Reseat the iPad firmly into the 30-pin connector.
  • If using a Lightning adapter, ensure it is compatible and properly connected, possibly using an extension cable.
  • Update the iPB-10 app and the IPB10 firmware to the latest versions.
펌웨어 업데이트에 실패했습니다.
  • USB 케이블이나 연결이 잘못되었습니다.
  • Outdated computer drivers.
  • Interrupted update process.
  • Ensure a direct, reliable USB connection between the IPB10 and your computer.
  • Download and install the correct firmware update utility and follow instructions precisely from the DigiTech support web대지.
  • Do not disconnect the USB cable or power during an update.
장치의 전원이 켜지지 않습니다.
  • 전원 어댑터가 연결되지 않았거나 결함이 있습니다.
  • 전원 콘센트가 작동하지 않습니다.
  • Verify the power adapter is securely connected to both the IPB10 and a working AC outlet.
  • 다른 장치로 콘센트를 테스트하세요.
  • Ensure you are using the correct power adapter for the IPB10.

8. 사양

특징세부 사항
모델 번호IPB10
품목 무게13.2파운드(5.99kg)
제품 치수7.13 x 24 x 15인치(18.11 x 60.96 x 38.1cm)
전원코드식 전기
권tage9 볼트
신호 형식비슷한 물건
색상검은색
Effects Library87 Pedals, 54 Amps, 26 Cabinets
사전 설정Infinite number of presets, 100 footswitch accessible
iPad 호환성Requires iPad with 30-pin connector (adapters may be needed for newer models)

9. 보증 정보

The DigiTech IPB10 is covered by a manufacturer's warranty. Please refer to the warranty card included with your product or visit the official DigiTech web보증 조건, 약관 및 등록에 대한 자세한 정보는 해당 웹사이트를 참조하십시오. 보증 청구를 위해 구매 증빙 자료를 보관하십시오.

10. 고객 지원

For technical assistance, product inquiries, or service, please contact DigiTech customer support.

  • Web대지: Visit the official DigiTech website for FAQs, firmware downloads, and support resources.
  • 연락하다: Refer to the "Contact Us" section on the DigiTech web전화번호 또는 이메일 지원 옵션을 제공하는 사이트입니다.

© 2024 DigiTech. 모든 권리 보유. 사양은 예고 없이 변경될 수 있습니다.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.