1. 제품 오버view
This manual provides essential information for the safe and effective use of your Ushio BC1618 FCL J120V-500W Halogen Projector Light Bulb. Please read these instructions carefully before installation and operation.
제품 설명
The Ushio BC1618 is a 500-watt, 120-volt halogen incandescent light bulb designed for projector, stage, and studio applications. It features a T2.5 shape with a Recessed Single Contact (R7s) base, providing a clear light output with a color temperature of 3,000K.
주요 특징
- 왓tage: 500와트
- 권tage: 120V
- 기본 유형: R7s (Recessed Single Contact)
- 색온도: 3,000K
- 광속: 10,000루멘
- 평균 수명: 2,000시간
- 마치다: 분명한
Figure 1: Ushio BC1618 FCL J120V-500W Halogen Projector Light Bulb.
2. 안전 정보
Always observe the following safety precautions to prevent injury or damage to the product and equipment.
- 전원 차단: Always disconnect power to the fixture before installing, removing, or handling the bulb.
- 고온: Halogen bulbs operate at high temperatures. Allow the bulb to cool completely before touching it.
- 직접적인 접촉을 피하세요: Do not touch the glass part of the bulb with bare hands. Oils from your skin can create hot spots, leading to premature failure. Use a clean cloth or gloves if handling is necessary.
- 적절한 경기: Use only in fixtures designed for halogen bulbs of the specified wattage 및 voltage.
- 통풍: 과열을 방지하기 위해 조명기구 주변에 적절한 환기를 확보하세요.
- 처분: 사용한 전구는 해당 지역 규정에 따라 폐기하세요.
- 눈 보호: Wear appropriate eye protection during installation or removal to guard against potential glass breakage.
3. 설치 지침
Follow these steps to safely install the Ushio BC1618 projector light bulb.
- 전원이 꺼져 있는지 확인하세요. Before beginning, confirm that the power supply to the projector or fixture is completely disconnected.
- 냉각 허용: If replacing an old bulb, ensure it has cooled down completely to avoid burns.
- Access Bulb Compartment: Open the bulb access panel on your projector or fixture. Refer to your projector's manual for specific instructions on accessing the bulb.
- 오래된 전구 제거: Carefully grasp the old bulb (using a cloth or gloves if it's a halogen type) and gently pull it straight out from its R7s base. Avoid twisting.
- 새 전구를 다루세요: Remove the new Ushio BC1618 bulb from its packaging. Do not touch the glass envelope with bare hands. Use the packaging, a clean cloth, or gloves to handle the bulb.
- 새 전구 삽입: Align the pins of the new bulb with the slots in the R7s base. Gently push the bulb straight into the socket until it is firmly seated. Do not force it.
- 보안 구획: Close and secure the bulb access panel.
- 복원력 : Reconnect the power supply to the projector or fixture.
Figure 2: Approximate dimensions of the Ushio BC1618 bulb, showing its length of 4.8 inches (12 cm).
4. 운영
Once the Ushio BC1618 bulb is correctly installed, operate your projector or fixture as per its manufacturer's instructions. The bulb will illuminate immediately upon power application.
- 워밍업 시간: Halogen bulbs provide instant full brightness.
- 냉각: After use, allow the projector or fixture to cool down for several minutes before moving or storing it. This helps prolong the life of the bulb and other components.
- 디밍 : If your fixture supports dimming, ensure it is compatible with halogen incandescent bulbs.
5. 유지관리
Proper maintenance can extend the life of your Ushio BC1618 bulb and ensure optimal performance.
- 청소: If the bulb's glass envelope becomes dirty, gently wipe it with a clean, lint-free cloth moistened with isopropyl alcohol. Ensure the bulb is completely cool and power is disconnected before cleaning.
- 점검: 전구와 소켓에 손상, 부식 또는 느슨한 연결 부위가 있는지 주기적으로 점검하십시오.
- 저장: 여분의 전구는 손상을 방지하기 위해 원래 포장 상태로 서늘하고 건조한 곳에 보관하십시오.
6. 문제 해결
If you encounter issues with your Ushio BC1618 bulb, refer to the following common problems and solutions.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 전구가 켜지지 않습니다. | No power to fixture; Bulb not seated correctly; Bulb has reached end of life; Faulty fixture. | Check power connection and circuit breaker. Ensure bulb is fully inserted. Replace bulb if it has exceeded its average lifetime. Consult a qualified technician for fixture repair. |
| 전구가 깜박입니다. | Loose connection; Incompatible dimmer; Voltag전자 변동. | Ensure bulb is securely seated. Verify dimmer compatibility. Check power supply for stability. |
| 전구가 빨리 타버립니다. | 오버볼tage; Frequent switching; Excessive vibration; Touching glass with bare hands during installation. | 올바른 볼륨 확인tage supply. Reduce frequency of on/off cycles. Ensure fixture is stable. Reinstall bulb carefully, avoiding skin contact with glass. |
7. 기술 사양
| 상표 | 우시오 |
| 모델 번호 | BC1618 (1000488) |
| 라이트 타입 | Halogen Incandescent |
| 왓tage | 500 와트 |
| 권tage | 120 볼트 |
| 전구 모양 크기 | T2.5 (119MM length) |
| 기본 유형 | R7s (Recessed Single Contact) |
| 색온도 | 3000 켈빈 |
| 명도 | 10000루멘 |
| 평균 수명 | 2000시간 |
| 마치다 | 분명한 |
| 재료 | 구리 |
| 제품 치수 | 5.5 x 1 x 1인치(약 13.97 x 2.54 x 2.54cm) |
| 품목 무게 | 0.48 온스(약 13.6그램) |
| 특정 용도 | Projector, Stage, Studio |
| 한국어: | 048777131718 |
8. 보증 및 지원
보증 정보
The manufacturer states that a specific warranty description is 적용 불가 for this product. Please refer to the retailer's return policy for any issues.
고객 지원
For further assistance or inquiries regarding the Ushio BC1618 projector light bulb, please contact your point of purchase or refer to the manufacturer's official web지원 리소스 사이트.