Mitutoyo 543-470B Absolute LCD Digimatic Indicator Id-C User Manual

1. 제품 오버view

The Mitutoyo 543-470B Absolute LCD Digimatic Indicator Id-C is a precision measuring instrument designed for accurate dimensional measurement. It features an LCD display and utilizes an absolute electrostatic capacitance type linear encoder for reliable readings. This indicator is as compact as standard Series 2 dial indicators, offering a large, easy-to-read display.

주요 특징은 다음과 같습니다.

• Absolute Encoder: Always displays the spindle's absolute position from the origin at power-on, eliminating over-speed errors.
• Go/No-Go Judgment: Allows setting upper and lower tolerance limits, displaying judgment results in full-size characters.
• Counting Direction Switching: The positive/negative count resulting from spindle movement can be toggled.
• 데이터 출력: Equipped with SPC data output for integration with data collection systems.
• Rotatable Face: The indicator face can be rotated 330 degrees for optimal view각도를 나타냅니다.
• Internal Calculations: Supports simple formula calculations (F(x) = Ax).

Figure 1: Mitutoyo 543-470B Absolute LCD Digimatic Indicator Id-C. This image shows the side profile of the digital indicator, highlighting its compact design, LCD display housing, and the measuring spindle.

2. 설정

2.1 배터리 설치

The indicator requires one SR44 battery (included). To install or replace the battery:

1. 일반적으로 디스플레이 장치의 뒷면이나 측면에 있는 배터리함 덮개를 찾으십시오.
2. 조심스럽게 뚜껑을 여세요.
3. Insert the SR44 battery with the correct polarity, usually indicated within the compartment.
4. 배터리 함 덮개를 단단히 닫습니다.

The battery life is approximately 5,000 hours under normal use.

2.2 표시기 장착

The 543-470B indicator features an 8mm stem diameter and an M2.5 x 0.45 thread for mounting. It is designed with a flat back for secure attachment to various fixtures or stands.

1. Ensure the mounting surface or fixture is clean and stable.
2. Insert the 8mm stem into the appropriate mounting hole on your fixture.
3. Secure the indicator using the clamping mechanism of your fixture. Ensure it is held firmly but do not overtighten to avoid damage.
4. If using the M2.5 x 0.45 threaded back, attach it to a compatible threaded mount.

3. 사용 설명서

3.1 전원 켜기/끄기

를 누르세요 켜짐/꺼짐 button to power the indicator on or off. Due to the absolute encoder, the indicator will display the spindle's absolute position upon power-on without needing to re-set the origin.

3.2 Origin-Set / Preset

The origin-set function establishes a reference point for measurement. The preset function allows setting a specific value at a given point.

• Origin-Set: Position the spindle at the desired zero reference point. Press the 기원 button to set this position as zero.
• 사전 설정: Move the spindle to the desired preset position. Use the 사전 설정 button and numerical input (if available) to enter a specific value for that position.

3.3 Zero-Set

The zero-set function temporarily sets the current spindle position to zero for incremental measurements, without affecting the absolute origin.

• Position the spindle at the desired temporary zero point.
• 를 누르세요 제로/ABS button to set the display to zero. Subsequent measurements will be relative to this point.
• 누르다 제로/ABS 다시 절대 측정 모드로 돌아갑니다.

3.4 Go/No-Go Judgment

This function allows for quick verification of whether a measurement falls within specified tolerance limits.

1. Set the upper and lower tolerance limits using the appropriate buttons (refer to the device's specific button layout for 'TOL' or 'LIMIT' settings).
2. As measurements are taken, the display will indicate 'GO' (within limits) or 'NG' (outside limits) in full-size characters.

3.5 Counting Direction Switching

The indicator allows you to reverse the counting direction (positive/negative) based on the spindle's movement. This is useful for different measurement setups.

• 위치 디렉터 or +/- 단추.
• Press this button to toggle the counting direction.

3.6 데이터 출력

The indicator is equipped with SPC data output. Connect a compatible data cable (sold separately) to the data output port to transfer measurement data to a computer or data processor.

3.7 Inch/Millimeter Conversion

For inch/metric models, a dedicated button allows switching between metric (mm) and imperial (inch) units.

• 를 누르세요 안으로/MM button to toggle between measurement units.

4. 유지관리

4.1 청소

The indicator has a dust/water protection level of IP42 or IP53 (dust-proof type). To maintain its performance:

• Wipe the display and body with a soft, dry cloth.
• 잘 지워지지 않는 얼룩은 천으로 가볍게 닦아내세요.ampened with mild detergent, then wipe dry immediately.
• Do not use organic solvents (e.g., thinner, benzene) as they may damage the plastic components.
• Keep the measuring spindle clean and free of debris.

4.2 배터리 교체

Replace the SR44 battery when the low voltage alarm appears on the display. Refer to Section 2.1 for battery installation instructions.

4.3 보관

Store the indicator in a clean, dry environment, away from direct sunlight, extreme temperatures, and high humidity. If storing for an extended period, it is recommended to remove the battery.

5. 문제 해결

이 섹션에서는 흔히 발생하는 문제와 그에 대한 잠재적인 해결책을 다룹니다.

6. 사양

7. 보증 및 지원

For warranty information, technical support, or service inquiries regarding your Mitutoyo 543-470B Absolute LCD Digimatic Indicator Id-C, please contact Mitutoyo customer service or your authorized Mitutoyo dealer. Please have your model number (543-470B) and purchase details available when contacting support.

You can find contact information on the official Mitutoyo web사이트나 제품 설명서를 통해 확인하세요.