STIEBEL ELTRON 233307 WPSF Brine Filling Unit
ಸಾಮಾನ್ಯ ಮಾಹಿತಿ
This document is intended for qualified contractors
ಸೂಚನೆ: Read these instructions carefully before using the appliance and retain them for future reference. Pass on these instructions to a new user if required.
ಈ ದಸ್ತಾವೇಜಿನಲ್ಲಿರುವ ಇತರ ಚಿಹ್ನೆಗಳು
ಸೂಚನೆ: General information is identifed by the adjacent symbol.
ಈ ಚಿಹ್ನೆಯು ನೀವು ಏನನ್ನಾದರೂ ಮಾಡಬೇಕು ಎಂದು ಸೂಚಿಸುತ್ತದೆ. ನೀವು ತೆಗೆದುಕೊಳ್ಳಬೇಕಾದ ಕ್ರಮವನ್ನು ಹಂತ ಹಂತವಾಗಿ ವಿವರಿಸಲಾಗಿದೆ.
ಸಂಬಂಧಿತ ದಾಖಲೆಗಳು
Heat pump operating and installation instructions
ಮಾಪನದ ಘಟಕಗಳು
Note: All measurements are given in mm unless stated otherwise.
ಸುರಕ್ಷತೆ
Only a qualified contractor should carry out installation, commissioning, maintenance and repair of the appliance.
ಸಾಮಾನ್ಯ ಸುರಕ್ಷತಾ ಸೂಚನೆಗಳು
We guarantee trouble-free function and operational reliability only if original accessories and spare parts intended for the appliance are used.
ಸೂಚನೆಗಳು, ಮಾನದಂಡಗಳು ಮತ್ತು ನಿಯಮಗಳು
Note: Observe all applicable national and regional regulation
ಉದ್ದೇಶಿತ ಬಳಕೆ
The brine charging unit is a multi-function valve for filling and filtering brine-based fluids. Any other use beyond that described shall be deemed inappropriate. Observation of these instructions and of the instructions for any accessories used is also part of the correct use of this appliance.
ಉತ್ಪನ್ನ ವಿವರಣೆ
The product includes a safety valve, a pressure gauge, a filter, a quick-action air vent valve and a microbubble separator.
ಪ್ರಮಾಣಿತ ವಿತರಣೆ
- ಸುರಕ್ಷತಾ ಕವಾಟ
- ಹುಕ್ ವ್ರೆಂಚ್
ತಯಾರಿ
The product is installed in the heat source system in the heat pump installation room.
- Observe the flow direction (see chapter “Specification/Dimensions and connections”).
- When installing the product, ensure that it is horizontal and free from stress.
ಕನಿಷ್ಠ ಅನುಮತಿಗಳು
Maintain the minimum clearances to ensure trouble-free operation of the appliance and facilitate maintenance work.
ಅನುಸ್ಥಾಪನ
Fitting the drain hose
- Fit the drain hose supplied to the safety valve.
- Size the drain hose so that brine can drain off unimpeded when the safety valve is fully opened.
- Lay the safety valve drain hose with a constant fall to the drain.
- Ensure that the safety valve drain hose is open to the outside.
Charging the heat source system
- Shut-off valve, heat source flow
- Quick-action air vent valves
- Shut-off valve, heat pump flow
- ತುಂಬಿಸುವ
- ಹರಿಸುತ್ತವೆ
- Close the shut-off valve in the heat source flow.
- Open the shut-off valve in the heat pump flow.
- Connect the refrigerant flow line to the charging side of the unit.
- Connect the refrigerant return line to the draining side of the unit.
- Carry out a pressure test. Remove the safety valve and insert the plug supplied.
- ಸುರಕ್ಷತಾ ಕವಾಟ
- ಪ್ಲಗ್
- Check for tightness.
- Charge the heat source system to the required operating pressure. For this, observe the maximum operating pressure (see chapter “Specification/ Data table”)
- Close the shut-off valve in the heat pump flow.
- Remove the plug and refit the safety valve.
- Vent the heat source system via the quick-action air vent valve.
- After venting, close the quick-action air vent valve.
Removing the strainer
If there is a high pressure drop in the heat source system, you can remove the strainer in the filter chamber of the product (see chapter “Specification/ Pressure drop diagram”).
Material losses
For opening and closing the filter chamber, use exclusively the hook wrench supplied.
- ಸ್ಟ್ರೇನರ್
- ಕಾರ್ಟ್ರಿಡ್ಜ್ ಅನ್ನು ಫಿಲ್ಟರ್ ಮಾಡಿ
- Open the filter chamber. Remove the filter cartridge.
- Remove the strainer from the heat pump flow.
- Re-insert the filter cartridge. Close the filter chamber.
- Tighten the cover with a torque of 15 Nm.
- Open the shut-off valves in the heat source flow and the heat pump flow.
- Vent the heat source system via the quick-action air vent valve.
- After venting, close the quick-action air vent valve.
ನಿರ್ವಹಣೆ
- Clean the filter cartridge if required.
ವಿವರಣೆ
ಆಯಾಮಗಳು ಮತ್ತು ಸಂಪರ್ಕಗಳು
Pressure drop diagram
- Y Pressure drop [hPa]
- X Flow rate [1/h]
- 1 Pressure drop with filter cartridge and strainer
- 2 Pressure drop with filter cartridge
ಡೇಟಾ ಟೇಬಲ್
ಖಾತರಿ
The guarantee conditions of our German companies do not apply to appliances acquired outside of Germany. In countries where our subsidiaries sell our products a guarantee can only be issued by those subsidiaries. Such guarantee is only granted if the subsidiary has issued its own terms of guarantee. No other guarantee will be granted. We shall not provide any guarantee for appliances acquired in countries where we have no subsidiary to sell our products. This will not affect warranties issued by any importers.
ಪರಿಸರ ಮತ್ತು ಮರುಬಳಕೆ
We would ask you to help protect the environment. After use, dispose of the various materials in accordance with national regulations.
ದಾಖಲೆಗಳು / ಸಂಪನ್ಮೂಲಗಳು
 |
STIEBEL ELTRON 233307 WPSF Brine Filling Unit [ಪಿಡಿಎಫ್] ಅನುಸ್ಥಾಪನ ಮಾರ್ಗದರ್ಶಿ 233307, WPSF Brine Filling Unit, 233307 WPSF Brine Filling Unit |
