សៀវភៅណែនាំអ្នកប្រើប្រាស់ សំណួរ និងចម្លើយចម្លើយ
ឧសភា 03, 2025 - 05:03 AM
ដើម្បីដំឡើង Uolfin J7FNMQ-LWS24049-V7 3- ពន្លឺបូរាណសំរិទ្ធអន្តរកាល ពន្លឺ Vanity Vanity Lightសូមអនុវត្តតាមជំហានទាំងនេះ៖
1. Before starting the installation, make sure to turn off the power. Go to the main fuse or circuit breaker box in your home and place the main power switch in the "OFF" position. Also, ensure that the wall switch is in the "OFF" position.
2. Ensure that the mounting surface is clean, dry, flat, strong enough, and 1/4" larger than the canopy on all sides. Correct any gaps between the mounting surface and canopy exceeding 3/16" as required.
3. Check if the ceiling or wall can support the weight of the lamp មុនពេលដំឡើង។
4. សូមប្រាកដថាវ៉ុលtage ដែលអ្នកកំពុងប្រើគឺ 120V និងវ៉ាត់អតិបរមាtage ក្នុងមួយអំពូលគឺ 40W ។
៥.១. រក្សាលីត្រamp ឆ្ងាយពីសារធាតុអាស៊ីត និងអាល់កាឡាំង ដើម្បីជៀសវាងការបំផ្លាញផ្ទៃ។
6. នៅពេលជំនួសអំពូល សូមបិទ ឬដកខ្សែភ្លើងamp ហើយរង់ចាំរហូតដល់វាត្រជាក់ ព្រោះអំពូលអាចក្តៅបានលឿន។
Now, let's proceed with the assembly and installation:
Step 1: Unscrew the xxxx nuts (H) from the back plate (G) and gently remove the mounting plate (F). Set them aside for later installation.
Step 2: Pass the supply wires from the outlet box through the mounting plate (F). If necessary, drill holes on the wall for the anchors (A), attach the mounting plate (F) to the outlet box with mounting screws (C), and mark the holes. Remove the mounting plate (F), drill the holes, and insert the anchors (A) until they are level with the wall. Secure the mounting plate (F) to the outlet box with mounting screws (C) and wood screws (B).
Step 3: Make wire connections according to the provided chart. Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Ensure that no wire strands are exposed and carefully tuck all wires into the outlet box.
Step 4: Align the holes in the back plate (G) with the pre-assembled mounting screws and attach the back plate (G) to the mounting plate (F) using the previously removed xxxx nuts (H). Hand tighten until snug.
Step 5: Unscrew the socket rings (L) from the sockets. Place the glass shades (K) on the iron frames (J) and secure them with the socket rings (L). Install bulbs (not included) according to the recommended maximum wattage.
Step 6: Double-check that everything is installed properly, and then you can turn on the light and enjoy!
សូមយោងទៅលើការផ្តល់ឱ្យ សៀវភៅណែនាំ for further details and illustrations. If you have any additional questions or concerns, you can contact Uolfin customer support at +1 850 296 2377 or email uolfin@newdecorworld.com during their working hours: Mon-Fri 9:00 a.m. - 16:00 p.m. EST.
បន្ថែមមតិយោបល់ថ្មី។