សៀវភៅណែនាំអ្នកប្រើប្រាស់ សំណួរ និងចម្លើយចម្លើយ
ថ្ងៃទី 16 ខែធ្នូ ឆ្នាំ 2024 - ម៉ោង 01:20 ព្រឹក
ដើម្បីសរសេរកម្មវិធី Philips SRP3016S/27 remote controlអ្នកមានជម្រើសពីរ៖ ការបញ្ចូលលេខកូដផ្ទាល់ ឬស្វែងរកលេខកូដស្វ័យប្រវត្តិ។ នេះគឺជាការណែនាំជាជំហាន ៗ សម្រាប់វិធីសាស្ត្រនីមួយៗ៖
ការបញ្ចូលលេខកូដផ្ទាល់ (បានណែនាំ)៖
1. Locate the Code List included with your remote. Find the section for the type of device you wish to control (e.g., TV, DVD, Blu-ray, etc.).
2. Circle all the remote codes for the brand of your device in the Code List.
3. Press and hold down the SETUP button on the remote until the red light on the remote control turns on. Release the SETUP button.
4. Press and release the device button on the remote for the type of device you wish to control (e.g., TV, DVD, Blu-ray, etc.). The red light will blink once and remain on.
5. ប្រើប៊ូតុងលេខនៅលើឧបករណ៍បញ្ជាពីចម្ងាយ ដើម្បីបញ្ចូលលេខកូដពីចម្ងាយ 4 ខ្ទង់ដំបូងដែលអ្នកគូសរង្វង់ក្នុងបញ្ជីកូដ។ ភ្លើងក្រហមនឹងបិទបន្ទាប់ពីចូលខ្ទង់ទីបួន។
6. Point the remote at the device and test the buttons to see if the device responds. If the buttons do not operate the device, repeat steps 4 and 5 with the next code you circled for that device.
7. ធ្វើជំហានទី 1-6 ម្តងទៀតសម្រាប់ឧបករណ៍នីមួយៗដែលអ្នកចង់គ្រប់គ្រង។
ស្វែងរកលេខកូដស្វ័យប្រវត្តិ៖
1. បើកឧបករណ៍ដែលអ្នកចង់គ្រប់គ្រងដោយដៃ។
2. Press and hold down the SETUP button on the remote until the red light on the remote control turns on. Release the SETUP button.
3. Press and release the device button on the remote for the type of device you wish to control (e.g., TV, DVD, Blu-ray, etc.). The red light will blink once and remain on.
4. ដោយប្រើឧបករណ៍បញ្ជាពីចម្ងាយ សូមចុច និងលែងប៊ូតុង POWER នៅលើឧបករណ៍បញ្ជាពីចម្ងាយ។ ឧបករណ៍បញ្ជាពីចម្ងាយនឹងផ្ញើលេខកូដ 10 ផ្សេងគ្នាទៅឧបករណ៍។ ភ្លើងក្រហមនឹងភ្លឹបភ្លែតៗសម្រាប់លេខកូដនីមួយៗ ហើយបន្តបើកបន្ទាប់ពីផ្ញើលេខកូដទាំង 10 រួចហើយ។
5. តើឧបករណ៍បិទឬ?
- If YES, go to Step 6.
- If NO, repeat Step 4 to test the next 10 codes.
6. បើកឧបករណ៍ឡើងវិញដោយដៃ។
7. With the remote pointed at the device, press and release the VOL UP button. The remote will re-send the first code of the 10 codes from Step 4. The red light will blink once and remain on.
8. តើឧបករណ៍បិទឬ?
- If YES, you have found a code for the device. Press and release the same device button you pressed in Step 3. This will store the code in the remote. Go to Step 9.
- If NO, continue to press and release the VOL DOWN button until the device turns off to test the other 9 codes from Step 4. Be sure to wait approximately 3 seconds after each VOL DOWN button press to allow the device time to respond to the code. When the device turns off, you have found a code for your device. Press and release the same device button pressed in Step 3. This will store the code in the remote. Go to Step 9.
9. Use the remote to turn the device back on and test the buttons to see if the device responds. If the buttons do not operate the device, repeat the Auto Code Search process for each device you wish to control.
Note: These instructions are a summary of the information provided in the Philips SRP3016S/27 Backlit Universal Remote Control User Manual. For more detailed instructions and troubleshooting tips, please refer to the manual.
បន្ថែមមតិយោបល់ថ្មី។