MINCO S220185PD Resistance Temperature Detectors
លក្ខណៈបច្ចេកទេស
- ការពិនិត្យឡើងវិញ: (B) Original release
- កាលបរិច្ឆេទ៖ ៧, ១១, ១៣
- អេកូ៖ -៤០, ៤៥
- Detail Specification No.: 4006/S220185 Page 1 of 14
ការពិពណ៌នា
| ការពិនិត្យឡើងវិញ | ការពិពណ៌នា | កាលបរិច្ឆេទ | អេកូ |
| (–) | ការចេញផ្សាយដើម។ | 02.09.2016 | — |
| (ក) | Update Figure 1 to allow leads to enter body in all configurations | 11.02.2018 | 2819759 |
| (ខ) | Change minimum temperature from -60°C to -196°C; remove PW element option | 06.03.2024 | 3511297 |
ទូទៅ
វិសាលភាព
- This specification details the ratings, physical and electrical characteristics, test and inspection data for Resistance Temperature Detectors (RTDs – thermally sensitive resistors),100, 1000, or 10000 ohms at 0°C with a temperature range of -196°C to 200°C.
- It shall be read in conjunction with ESCC Generic Specification No. 4006, the requirements of which are supplemented and superseded herein.
TYPE VARIANTS
- Variants of the basic type RTD specified herein which are also covered by this specification are given in the Minco S220185 specifications drawing.
ការវាយតម្លៃអតិបរមា
- The maximum ratings, which shall not be exceeded at any time during use or storage, applicable to the RTDs specified herein, are as scheduled in Table 1(b).
វិមាត្ររូបវិទ្យា
- The physical dimensions of the RTDs specified herein are shown in FIGURE 1 and Minco S220185 specifications drawing.
ដ្យាក្រាមមុខងារ
- The functional diagram for the RTDs specified herein is shown in FIGURE 2 and Minco S220185 specifications drawing.
ឯកសារដែលអាចអនុវត្តបាន។
The following documents form part of this specification and shall be read in conjunction with it:
- (ក) ESCC Generic Specification No. 4006, Thermistors (Resistors, Thermally Sensitive)
- (ខ) IEC 60410, Sampling Procedures and Tables for Inspections by Attributes
- (គ) MIL-STD-202, Test Methods for Electronic and Electrical Component Parts
- (ឃ) Minco specification drawing S220185
- (ង) IEC 60751, Industrial Platinum Resistance Thermometers and Platinum Temperature Sensors
TERMS, DEFINITIONS, ABBREVIATIONS, SYMBOLS, UNITS
For the purpose of this specification, the terms, definitions, abbreviations, symbols and units specified in ESCC Basic Specification No. 21300 shall apply. In addition, the following symbols are used:
- NTC = Negative Temperature Coefficient
- ភីធីស៊ី = Positive Temperature Coefficient
- RZ = Zero Power Resistance
- RM = Minimum Temperature Resistance
- RL = Low Temperature Resistance
- RH = High Temperature Resistance
- PD = Power Dissipation
- កំពូល = Operating Temperature Range
- ធីអេសធីជី = Storage Temperature Range
- mW = Milliwatt
- Ω = Ohms
TABLE 1(a) – Element Variant Resistance/Temperature Characteristics
|
វ៉ារ្យ៉ង់ |
RZ |
Resistance/Temperature Characteristics (Note 2) | Temperature Coefficient (Ω/Ω/°C) | ||||||
| -196 អង្សាសេ
(ចំណាំ 3) |
-50 អង្សាសេ | 0°C
(ចំណាំ 1) |
+៨៥ អង្សាសេ | +៨៥ អង្សាសេ | +៨៥ អង្សាសេ | +៨៥ អង្សាសេ | |||
|
PD |
Nom. (Ω) | 20.25 | 80.31 | 100.00 | 109.73 | 128.99 | 138.51 | 175.86 |
0.00385 |
| Tol. (±%) | 5.45 | .១២៥ | .១២៥ | .១២៥ | .១២៥ | .១២៥ | .១២៥ | ||
| Tol. (±°C) | 2.56 | .១២៥ | .១២៥ | .១២៥ | .១២៥ | .១២៥ | 1.3 | ||
|
PF |
Nom. (Ω) | 202.5 | 803.1 | 1000.0 | 1097.3 | 1289.9 | 1385.1 | 1758.6 |
0.00385 |
| Tol. (±%) | 5.45 | .១២៥ | .១២៥ | .១២៥ | .១២៥ | .១២៥ | .១២៥ | ||
| Tol. (±°C) | 2.56 | .១២៥ | .១២៥ | .១២៥ | .១២៥ | .១២៥ | 1.3 | ||
|
PS |
Nom. (Ω) | 2025 | 8031 | 10,000 | 10,973 | 12,899 | 13,851 | 17,586 |
0.00385 |
| Tol. (±%) | 5.45 | .១២៥ | .១២៥ | .១២៥ | .១២៥ | .១២៥ | .១២៥ | ||
| Tol. (±°C) | 2.56 | .១២៥ | .១២៥ | .១២៥ | .១២៥ | .១២៥ | 1.3 | ||
ចំណាំ៖
- The reference resistance is specified at 0°C.
- Resistance shall be measured as specified in 8.3.1.1 at 0°C, pursuant to the deviations of 4.2.2 herein.
- IEC 60751 does not define class B (F 0.3) tolerance at temperatures below -50°C for thin-film elements.
The stated tolerance for S220185 at -196°C is based on double the tolerance allowed for wire wound elements per IEC 60751 at the minimum temperature.
TABLE 1(b) – Maximum Ratings
| លក្ខណៈ | និមិត្តសញ្ញា | ការវាយតម្លៃអតិបរមា | ឯកតា | សុន្ទរកថា |
| ការផ្តាច់ថាមពល | PD | 2 | mW | កំណត់សំគាល់ ១, ២ |
| ជួរសីតុណ្ហភាពប្រតិបត្តិការ | កំពូល | -៥០ ទៅ ៥០ | °C | |
| ជួរសីតុណ្ហភាពផ្ទុក | ធីអេសធីជី | -៥០ ទៅ ៥០ | °C |
ចំណាំ៖
- Never to be exceeded in the temperature measurement mode. The RTDs specified herein shall not be used in the self-heat mode.
- Assuming maximum excitation current of 1 mA for PD, PF, PW variants, and maximum excitation current of 0.3 mA for PS variant.
វិមាត្រ
រូបភាពទី 1 – វិមាត្ររូបវិទ្យា
| និមិត្តសញ្ញា | មីលីម៉ែត្រ | |
| នាទី | អតិបរមា | |
| A | 14.2 | 15.8 |
| B | * | * |
| C | 6.2 | 7.8 |
| D | – | 2.0 |
*Variable dimension as specified by model number. See S220185 specifications drawing for complete details.
ដ្យាក្រាមមុខងារ
រូបភាពទី 2 – FUNCTIONAL DIAGRAM
តម្រូវការ
ទូទៅ
The complete requirements for procurement of the RTDs specified herein are stated in this specification and ESCC Generic Specification No. 4006 for Thermistors (Resistors, Thermally Sensitive). Deviations from the Generic Specification, applicable to this specification only, are listed in Para. 4.2.
DEVIATIONS FROM GENERIC SPECIFICATION
- Deviation from Marking (ESCC General Specification No. 4006 Para. 4.4)
The component is too small to accommodate all of the marking specified. The required marking information, in full, shall accompany the component in its primary package. - Deviation from Zero Power Resistance (ESCC General Specification No. 4006 Para. 8.3.1.1)
- (ក) Sensors will not be mounted on brass rods or mounting plates.
- (ខ) Clips shall grip the leads within 13mm from the end of the leadwires.
- Deviation from Insulation Resistance (ESCC General Specification No. 4006 Para. 8.3.1.4) Sensors will be “immersed” in conductive metal shot “bath” in place of a V-block. Points of measurement shall be between sensor leads (shorted together) and metal shot “bath”.
- Deviations from Production Control (Chart F2)
- Internal Visual Inspection (ESCC General Specification No. 4006 Para. 5.2.1) Not applicable. The cover material is transparent, allowing any non-conformance to be found in External Visual Inspection.
External Visual Inspection (ESCC General Specification No. 4006 Para. 5.2.4)
Visual inspection will be used to determine compliance to the following:
- (ក) No residue from manufacturing process(es)
- (ខ) 0.005” minimum continuous seal (lamination)
- (គ) No tears or cuts with potential to propagate
- (ឃ) No crease or wrinkle that obstructs the contact surface of the sensing element, or covers more than 25% of the surface area
- (ង) No metallic foreign material that reduces spacing between un-insulated conductors to less than 0.002”, or reduces conductor/trim border to less than 0.005”
- (f) No foreign material that crosses or potentially damages a conductor, or is visible with an unaided eye
- (g) No cracks in thin-film ceramic substrate
- (ម៉ោង) No displaced or missing thin-film glass
- (i) No exposed bare leads
Weight (ESCC General Specification No. 4006 Para. 5.2.6) Not applicable. Weight is dependent on variant selections.
Deviations from Screening Tests (Chart F3)
Radiographic Inspection (ESCC General Specification No. 4006 Para. 8.6) Not applicable. The cover material is transparent, allowing any non-conformance to be found in External Visual Inspection.
External Visual Inspection (ESCC General Specification No. 4006 Para. 8.5)
- Visual inspection will be used to determine compliance to the following:
- (ក) No residue from manufacturing process(es)
- (ខ) 0.005” minimum continuous seal (lamination)
- (គ) No tears or cuts with potential to propagate
- (ឃ) No crease or wrinkle that obstructs the contact surface of the sensing element, or covers more than 25% of the surface area
- (ង) No metallic foreign material that reduces spacing between un-insulated conductors to less than 0.002”, or reduces conductor/trim border to less than 0.005”
- (f) No foreign material that crosses or potentially damages a conductor, or is visible with an unaided eye
- (g) No cracks in thin-film ceramic substrate
- (ម៉ោង) No displaced or missing thin-film glass
- (i) No exposed bare leads
Deviations from Qualification and Periodic Tests (Chart F4)
Shock (ESCC General Specification No. 4006 Para. 8.7)
- Shock will not be performed.
Vibration (ESCC General Specification No. 4006 Para. 8.8)
- Vibration will not be performed.
Dielectric Withstanding Voltage (ESCC General Specification No. 4006 Para. 8.9)
- Dielectric Withstanding Voltage នឹងមិនត្រូវបានអនុវត្តទេ។
External Visual Inspection (ESCC General Specification No. 4006 Para. 8.5)
- Visual inspection will be used to determine compliance to the following:
- (ក) No residue from manufacturing process(es)
- (ខ) 0.005” minimum continuous seal (lamination)
- (គ) No tears or cuts with potential to propagate
- (ឃ) No crease or wrinkle that obstructs the contact surface of the sensing element, or covers more than 25% of the surface area
- (ង) No metallic foreign material that reduces spacing between un-insulated conductors to less than 0.002”, or reduces conductor/trim border to less than 0.005”
- (f) No foreign material that crosses or potentially damages a conductor, or is visible with an unaided eye
- (g) No cracks in thin-film ceramic substrate
- (ម៉ោង) No displaced or missing thin-film glass
- (i) No exposed bare leads
Resistance to Soldering Heat (ESCC General Specification No. 4006 Para. 8.10)
- Not applicable. The sensor body can never be exposed to solder within the distance specified. Minimum lead length variant is 1 inch (25.4mm).
Moisture Resistance (ESCC General Specification No. 4006 Para 8.11)
- Moisture Resistance will not be performed.
Solderability (ESCC General Specification No. 4006 Para 8.14)
- Stripped end of leads shall be immersed to within ±1.25mm of lead insulation.
Terminal Strength (ESCC General Specification No. 4006 Para 8.15)
- Initial and final zero power resistance shall be measured as specified in 8.3.1.1 at 0°C, pursuant to the deviations of 4.2.2 herein.
Short Time Load (ESCC General Specification No. 4006 Para. 8.16)
- Final zero power resistance shall be measured as specified in 8.3.1.1 at 0°C, pursuant to the deviations of 4.2.2 herein.
Low Temperature Storage (ESCC General Specification No. 4006 Para. 8.17)
- Initial and final zero power resistance shall be measured as specified in 8.3.1.1 at 0°C, pursuant to the deviations of 4.2.2 herein.
Operating Life (ESCC General Specification No. 4006 Para. 8.18)
- Ambient temperature shall be controlled by convection oven and sensors will be energized as specified in Table 3 herein.
Permanence of Marking (ESCC General Specification No. 4006 Para. 8.19)
- Not applicable. The component is too small to accommodate all of the marking specified. The required marking information, in full, shall accompany the component in its primary package.
សម្គាល់
ទូទៅ
The marking of all components delivered to this specification shall be in accordance with requirements of ESCC Basic Specification No. 21700 and the following: The component is too small to accommodate all of the marking specified. The required marking information, in full, shall accompany the component in its primary package.
The information to be marked and the order of precedence shall be as follows:
- (ក) ESCC Component number
- (ខ) Traceability Information
- (គ) Manufacturer’s name or symbol (order of precedence per ESCC 21700 para. 4.4)
Tolerance and temperature coefficient are as specified in Table 1(a) per the corresponding variant.
The ESCC Component Number
The ESCC Component Number shall be formed by grouping together the following:
- (a) The number of the relevant Detail Specification excluding the /: 4006S220185
- (b) Sensing element variant: PD, PF, PS, or PW [characteristics as defined in Table 1(a)]
- (c) Number of leads variant: Y (2 leads), Z (3 leads), or X (4 leads)
- (d) Lead insulation variant: T = PTFE or K = polyimide
- (e) Lead length variant: specified in (whole) inches
- (f) Outer surface type variant: A = non-adhering or B = adhering (one side)
- (g) Testing level: F3 = Screening tests (Chart F3), F4 = Qualification and Periodic tests (Chart F4), or blank for Production Control (Chart F2) only
- (h) The total dose radiation level letter
- Blank if radiation test is not required
- If radiation test has been specified, add suffix for total dose radiation level: add “-D” for lead insulation variant “T”, add “-H” for lead insulation variant “K” (D=10k rads, H=1M rads per ESCC 22900)
Exampលេ៖ 4006S220185PFZK40AF3
Traceability Information
Traceability information shall be comprised of the following:
- (ក) Manufacturing date code (yyww)
- (ខ) Lot/batch code
- (គ) លេខស៊េរី
Exampលេ៖ 1223-379799-*-*-108
Manufacturer’s Name or Symbol
Each component package will be marked with Minco’s name and/or logo.
សំភារៈនិងថវិកា
The materials and finishes shall be as specified herein. Where a definite material is not specified, a material which will enable the sensors specified herein to meet the performance requirements of this specification shall be used. Acceptance or approval of any constituent material does not guarantee acceptance of the finished product.
រាងកាយ
- The sensing element shall be laminated between layers of polyimide film.
Lead Material and Finish
- The lead material shall be insulated stranded silver-plated copper wire.
TEST METHODS AND PROCEDURES
Production Control (Chart F2)
ការឆក់កម្ដៅ
- Thermal shock shall be performed in accordance with MIL-STD-202 Method 107 as directed by ESCC Generic Specification No. 4006. The test condition shall be C except sub-zero temperature will be – 55°C, number of cycles will be 10, and exposure time at temperature extremes will be 15 minutes minimum.
Room Temperature Electrical Measurements
- Unless otherwise specified, this will consist of zero-power resistance measurements at 0°C. Acceptable limits are as specified in Table 1(a).
Dimension Check
- The dimensions shall conform to those specified in Figure 1 herein.
Screening Tests (Chart F3)
Parameter Drift Values
- The maximum parameter drift values (D) are specified in Table 2 herein. Unless otherwise stated, measurements shall be performed at 0°C.
ដុតចូល
- The conditions for burn-in shall be as specified in Table 3 herein.
High, Low, and Minimum Temperatures Electrical Measurements
The resistance at high, low, and minimum temperatures shall be measured in accordance with Table 1(a) herein.
Room Temperature Electrical Measurements
- Unless otherwise specified, this will consist of zero-power resistance measurements at 0°C. Acceptable limits are as specified in Table 1(a).
Qualification and Periodic Tests (Chart F4)
Intermediate and End-Point Electrical Measurements
- The parameters to be measured and inspections to be performed at intermediate and end points during qualification and periodic tests are scheduled in Table 6.
Terminal Strength
- The test conditions for Terminal Strength shall be as follows:
- Applied Force: ៦៧.៥ ផោន (៣០០ អិន)
- រយៈពេល៖ 5 វិនាទី
ជីវិតប្រតិបត្តិការ
- The conditions for Operating Life testing shall be as specified in Table 3 herein.
តារាងទី 2 – Parameter Drift Values
| ទេ | លក្ខណៈ | និមិត្តសញ្ញា | អេស.ស៊ី.ស៊ី 4006 សាកល្បង វិធីសាស្រ្ត និង លក្ខខណ្ឌ | ដែនកំណត់ (D) | ឯកតា |
| 1 | Zero Power Resistance Drift | DRZ/RZ | ប៉ារ៉ា។ ៣
ប៉ារ៉ា។ ៣ (ចំណាំ 1) |
±0.2 | % |
ចំណាំ៖
- Deviations to Para. 8.3.1.1 per Para. 4.2.2 herein.
តារាង 3 – Conditions for Burn-in and Operating Life Tests
| ទេ | លក្ខណៈ | និមិត្តសញ្ញា | លក្ខខណ្ឌ | ឯកតា |
| 1 | Elevated Ambient Temperature | TEA | 200 ± 5 | °C |
| 2 | ការផ្តាច់ថាមពល | PD | 2 (ចំណាំ 1) | mW |
ចំណាំ៖
- Operating Life Test only. Burn-in Test is unpowered.
ការគ្រប់គ្រងផលិតកម្ម
តារាង 4 – Production Control Test Summary (Chart F2)
| អេស.ស៊ី.ស៊ី ទូទៅ ការបញ្ជាក់ ទេ 4006 | ការវាស់វែង និង អធិការកិច្ច |
និមិត្តសញ្ញា |
ដែនកំណត់ |
ឯកតា |
||||
| សាកល្បង ចំណងជើង | សាកល្បង វិធីសាស្រ្ត
និង នីតិវិធី |
សាកល្បង ប៉ារ៉ាម៉ែត្រ | ការកំណត់អត្តសញ្ញាណ | លក្ខខណ្ឌ | នាទី | អតិបរមា។ | ||
| Pre-Encapsulation
(Internal Visual) Inspection |
៣៥០/២៤០០ | មិនបានអនុវត្ត
(Note 1 per 4.2.4.1 herein) |
||||||
| ការឆក់កម្ដៅ | ៣៥០/២៤០០ | -55 +0/-5°C; 15 minutes min.
25 +10/-5°C; 10 minutes min. /15 minutes max. 200 +5/-0°C; 15 minutes min. 25 +10/-5°C; 10 minutes min. /15 minutes max. 10 cycles |
គ្មាន | គ្មាន | ||||
| Room Temperature Electrical Measurements | ៣៥០/២៤០០ | Zero Power Resistance | 0°C | RZ | Per Table 1(a) herein for specified variant | W | ||
| External Visual Inspection | ៣៥០/២៤០០ | 3 វិamples តែប៉ុណ្ណោះ
(Note 1 per 4.2.4.2 herein) |
ESCC20500/
ESCC2054000 |
Lot rejection for any
បរាជ័យ |
||||
| Dimension Check | ៣៥០/២៤០០ | 3 វិamples តែប៉ុណ្ណោះ | វិមាត្រ | In the event of a failure, test 100% | Per Figure 1 herein,
and S220185 specification drawing |
|||
| ទម្ងន់ | 5.2.6 | Dependent on variants (Note 1 per 4.2.4.3 herein) | ||||||
ចំណាំ៖
- Denotes exception to ESCC Generic Specification No. 4006.
តារាង 5 – Screening Tests Summary (Chart F3)
| អេស.ស៊ី.ស៊ី ទូទៅ ការបញ្ជាក់ ទេ 4006 | ការវាស់វែង និង អធិការកិច្ច |
និមិត្តសញ្ញា |
ដែនកំណត់ |
ឯកតា |
||||
| សាកល្បង ចំណងជើង | សាកល្បង វិធីសាស្រ្ត
និង នីតិវិធី |
សាកល្បង ប៉ារ៉ាម៉ែត្រ | ការកំណត់អត្តសញ្ញាណ | លក្ខខណ្ឌ | នាទី | អតិបរមា។ | ||
| Parameter Drift Values (Initial Measurements) | 8.3.2 | Zero Power Resistance | 0°C | RZ | Per Table 1(a) herein for specified variant | W | ||
| ដុតចូល | 8.4 | 200 ±5°C; 168 +14/-0 hours
គ្មានអំណាច |
||||||
| Parameter Drift Values (Final Measurements) | 8.3.2 | Zero Power Resistance | 0°C | RZ | Per Table 1(a) herein for specified variant | W | ||
| High, Low, and Minimum Temperatures Electrical Measurements | 8.3.3 | Minimum Temperature Resistance
Low Temperature Resistance |
-196 អង្សាសេ
-50 អង្សាសេ |
RM
RL |
Per Table 1(a) herein for specified variant Per Table 1(a) herein
for specified variant |
W
W |
||
| ធន់ទ្រាំនឹងសីតុណ្ហភាពខ្ពស់។ | 200°C | RH | Per Table 1(a) herein for specified variant | W | ||||
| Room Temperature Electrical Measurements | 8.3.4 | Zero Power Resistance | 0°C | RZ | Per Table 1(a) herein for specified variant | W | ||
| Radiographic Inspection | 8.6 | មិនបានអនុវត្ត
(Note 1 per 4.2.5.1 herein) |
||||||
| External Visual Inspection | 8.5 | (Note 1 per 4.2.5.2 herein) | ESCC 20500/ESCC2054000 | |||||
| Dimension Check | 8.5 | ESCC 20500 | Per Figure 1 herein,
and S220185 specification drawing |
|||||
ចំណាំ៖
- Denotes exception to ESCC Generic Specification No. 4006.
តារាងទី 6 – Intermediate and End-Point Electrical Measurements and Qualification and Periodic Tests Summary (Chart F4)
| ក្រុមរង 3 (12 បំណែក – ទេ បរាជ័យ permitted) | |||||||||
| អេស.ស៊ី.ស៊ី ទូទៅ ការបញ្ជាក់ ទេ 4006 | ការវាស់វែង និង អធិការកិច្ច |
និមិត្តសញ្ញា |
ដែនកំណត់ |
ឯកតា |
|||||
| សាកល្បង ចំណងជើង | សាកល្បង វិធីសាស្រ្ត
និង នីតិវិធី |
សាកល្បង ប៉ារ៉ាម៉ែត្រ | ការកំណត់អត្តសញ្ញាណ | លក្ខខណ្ឌ | នាទី | អតិបរមា។ | |||
| Dissipation Constant | 8.12 | Dissipation Constant | P(mW/°C) | 3 | mW/°C | ||||
| Thermal Time Constant | 8.13 | Thermal Tiime Constant | t | 30 | វិ | ||||
| ភាពអាចលក់បាន | 8.14 | Leads immersed within
±1.25mm of lead insulation. (Note 1 per 4.2.6.7 herein) |
Inspect per ANSI/J-STD-002 | Per ANSI/J-STD-002 | |||||
| Terminal Strength | 8.15 | 1 lb. for 5 seconds (each lead)
(Note 1 per 4.2.6.8 herein) |
Zero Power Resistance (initial) | 0°C
0°C |
RZ
DRZ/RZ |
(record only) | W
% |
||
| Parameter Drift (final) | -៤០ | +0.2 | |||||||
| Visual Examination (final) | No evidence of damage | ||||||||
| External Visual Inspection | 8.5 | (Note 1 per 4.2.6.4 herein) | ESCC 20500/ESCC2054000 | ||||||
| Dimension Check | 8.5 | ESCC 20500 | Per Figure 1 herein,
and S220185 specification drawing |
||||||
| ក្រុមរង 4 (20 បំណែក – ទេ បរាជ័យ គឺ permitted) | |||||||||
| អេស.ស៊ី.ស៊ី ទូទៅ ការបញ្ជាក់ ទេ 4006 | ការវាស់វែង និង អធិការកិច្ច |
និមិត្តសញ្ញា |
ដែនកំណត់ |
ឯកតា |
|||||
| សាកល្បង ចំណងជើង | សាកល្បង វិធីសាស្រ្ត
និង នីតិវិធី |
សាកល្បង ប៉ារ៉ាម៉ែត្រ | ការកំណត់អត្តសញ្ញាណ | លក្ខខណ្ឌ | នាទី | អតិបរមា។ | |||
| Short Time Load | 8.16 | Per Table 1(b) herein for specified variant
(Note 1 per 4.2.6.9 herein) |
Zero Power Resistance (final)
Visual Examination (final) |
0°C | RZ | Per Table 1(a) herein for specified variant No evidence of arcing,
burning, or charring |
W | ||
| ការផ្ទុកសីតុណ្ហភាពទាប | 8.17 | -62 ±3°C; 3 hours min
(Note 1 per 4.2.6.10 herein) |
Zero Power Resistance (initial) | 0°C
0°C |
RZ
DRZ/RZ |
(record only) | W
% |
||
| Parameter Drift (final) | -៤០ | +0.2 | |||||||
| Visual Examination (final) | No evidence of damage | ||||||||
| Operating Life 2000 hours | 8.18 | 200 ±5°C (convection oven); 2 mW energization
(Note 1 per 4.2.6.11 herein) |
Zero Power Resistance (initial)
Parameter Drift (1000 ±48 hours) Parameter Drift (from initial) (2000 ±48 hours) |
0°C
0°C 0°C |
RZ
DRZ/RZ DRZ/RZ |
Per Table 1(a) herein for specified variant | W
% % |
||
| -៤០
-៤០ |
+0.2
+0.2 |
||||||||
| Permanence of Marking | 8.19 | មិនបានអនុវត្ត
(Note 1 per 4.2.6.12 herein) |
|||||||
| External Visual Inspection | 8.5 | (Note 1 per 4.2.6.4 herein) | ESCC 20500/ESCC2054000 | ||||||
| Dimension Check | 8.5 | ESCC 20500 | Per Figure 1 herein, and S220185 specification drawing | ||||||
ចំណាំ៖
- Denotes exception to ESCC Generic Specification No. 4006.
Detail Specification No. 4006/S220185
សំណួរគេសួរញឹកញាប់
សំណួរ៖ តើខ្ញុំអាចកែប្រែផលិតផលសម្រាប់កម្មវិធីផ្ទាល់ខ្លួនបានទេ?
A: It is recommended to use the product as per the manufacturer's specifications to ensure safety and performance. Modifying the product may void warranty and pose risks.
សំណួរ: តើខ្ញុំគួរធ្វើដូចម្តេចប្រសិនបើផលិតផលមិនដំណើរការ?
A: ប្រសិនបើអ្នកជួបប្រទះបញ្ហាណាមួយជាមួយផលិតផល សូមមើលផ្នែកដោះស្រាយបញ្ហានៅក្នុងសៀវភៅណែនាំ ឬទាក់ទងផ្នែកជំនួយអតិថិជនសម្រាប់ជំនួយ។
ឯកសារ/ធនធាន
 |
MINCO S220185PD Resistance Temperature Detectors [pdf] ការណែនាំអំពីការដំឡើង S220185PD, S220185PF, S220185PS, S220185PD Resistance Temperature Detectors, S220185PD, Resistance Temperature Detectors, Temperature Detectors, Detectors |