IMPORTANT SAFETY INSTRUCTIONS AND INSTALLATION GUIDE

READ BEFORE INSTALLATION

SAVE THESE INSTRUCTIONS

Questions, problems, missing parts? Before returning to the store, call Feit Electric Customer Service: 8 a.m. - 5 p.m., PST, Monday - Friday. Phone: 1-866-326-BULB (2852). Website: FEIT.COM

Feit Electric appreciates your trust and confidence in purchasing this LED Portable Work Light. We are committed to creating quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Feit Electric.

Important Safety Information

READ ALL INSTRUCTIONS

• All Safety and Operating instructions in this manual must be followed before using this product.
• Follow all safeguards stated in the manual, in addition to normal safety precautions when working with electrical devices. Always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury.
• Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or for the wet location portable luminaire. Receptacles are available with built-in GFCI protection and can be used for this safety measure.
• Use only with an extension cord for outdoor use, such as an extension cord of cord type SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW, STOOW, SJEW, SJEOW, SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW, or SJTOOW.
• To disconnect, turn off the switch, then remove the plug from the outlet. Do not disconnect by pulling on the cord.
• To reduce the risk of fire, keep away from combustible materials while in operation.
• To reduce the risk of injury, close supervision is necessary when this product is used near children.
• Suitable for Wet Locations

SAVE THESE INSTRUCTIONS

⚠️ WARNING: RISK OF SHOCK. House electric current can cause painful shock or serious injury unless handled properly.

⚠️ WARNING: When using outdoor portable luminaires, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury.

⚠️ WARNING: Use only three-wire extension cords that have three-prong grounding plugs and grounding receptacles that accept the appliance's plug. Do not use an extension cord near water or in areas where water may accumulate. Keep away from pools or spas. Keep plugs dry.

CAUTION: This portable light-emitting diode (LED) luminaire has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug does not fully fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not alter the plug.

Maintenance and Care

Maintenance of this work light is very minimal. Regularly clean the lens with a non-abrasive cleaning cloth. The same care should be provided for the stand.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Feit Electric Company, 4901 Gregg Road, Pico Rivera, CA 90660. Website: www.feit.com, Phone: 1-800-543-3348.

Limited Warranty

This product is warranted to be free from defects in workmanship and materials for up to 3 years from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, visit feit.com/contact-us, or call 1-866 326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

Please contact 1-866-326-BULB (2852) for further assistance.

Pre-Assembly

PARTS INCLUDED

NOTE: Parts not shown to actual size.

PARTS OF THE LED WORK LIGHT

Diagram of the LED Work Light showing: a Carrying handle at the top, the Work Light Body, a Lens covering the LEDs at the front, and a Stand at the base. The back of the Work Light shows a Power Button.

Assembly

1. Step 1

   Take out the LED Work Light Body (AA), the H-Stand (BB), the Locking Knob (CC), the Locking Washer (DD), and the Washer (EE).

   Illustration showing the individual parts for assembly: LED Work Light Body (AA), H-Stand (BB), Locking Knob (CC), Locking Washer (DD), and Washer (EE).

2. Step 2

   Attach the LED Work Light Body (AA) to the H-Stand (BB) by first inserting the Locking Washer (DD) and Washer (EE) onto the Locking Knob (CC). Then, screw the Locking Knob (CC) through the LED Work Light Body (AA) and into the stand (BB) (see Fig. 1). Tighten the Locking Knob (CC) to set into place.

   Figure 1 illustrates the attachment of the LED Work Light Body (AA) to the H-Stand (BB) using the Locking Knob (CC), Locking Washer (DD), and Washer (EE).

3. Step 3

   Once the LED Work Light Body (AA) has been attached to the Stand (BB), the LED Work Light can pivot vertically and horizontally into the desired position.

   Horizontal Pivoting

   To pivot horizontally, loosen the center Locking Knob, then adjust the work light to your preferred position. Once set to your desired position, re-tighten the center Locking Knob to lock it into place. This allows for side-to-side adjustment.

   Diagram illustrating horizontal pivoting of the work light, with arrows showing side-to-side movement controlled by the center Locking Knob.

   Vertical Pivoting

   To pivot vertically, simply adjust the Work Light to your preferred position. Once set to your desired position, additional tightening can be done using the Hex Key Allen Wrench (FF) found on the sides of the work light.

   Diagram illustrating vertical pivoting of the work light, with arrows showing up-and-down movement. The Hex Key Allen Wrench (FF) is indicated for additional tightening.