PROLIGHTS ÆtherBox LITE

Thank you for choosing PROLIGHTS. This product has been designed in Italy to meet quality and performance requirements for professionals. Any other use, if not expressly indicated, could compromise the product's condition/operation or be a source of danger. This product is meant for professional use and commercial use is subject to applicable national accident prevention rules and regulations.

Features, specifications, and appearance are subject to change without notice. Music & Lights S.r.l. and affiliated companies disclaim liability for any injury, damage, or loss arising from the use of, inability to use, or reliance on this document.

The product user manual can be downloaded from www.prolights.it or inquired from official PROLIGHTS distributors (PROLIGHTS Sales Network).

Scanning the QR code (not included here) accesses the download area for technical documentation, including specifications, user manuals, technical drawings, photometrics, personalities, and firmware updates.

PROLIGHTS is a trademark of Music & Lights S.r.l. All rights reserved. Music & Lights is located at Via A. Olivetti, snc, 04026 - Minturno (LT) ITALY.

Safety Information

[Warning] Please read the following instructions carefully before installing, powering, operating, or servicing the product. Observe these indications for future handling.

This unit is for professional use only, not for household or residential use.

Connection to Mains Supply

• Connection must be carried out by a qualified electrical installer.
• Use only AC supplies 100-240V 50-60 Hz. The fixture must be electrically connected to ground (earth).
• Select cable cross-section according to the maximum current draw and the number of products on the same power line.
• The AC mains power distribution circuit must be equipped with magnetic+residual current circuit breaker protection.
• Do not connect to a dimmer system, as this may damage the product.

Protection and Warning Against Electrical Shock

• Do not remove any cover. Always disconnect the product from power before servicing.
• Ensure the fixture is connected to Class III equipment operating at safety extra-low voltages (SELV) or protected extra-low voltages (PELV). Use an AC power source compliant with local codes, with overload and ground-fault protection.
• Before use, check that all power distribution equipment and cables are in perfect condition and rated for the connected devices' current requirements.
• Immediately isolate the fixture from power if the power plug, seal, cover, cable, or other components are damaged, defective, deformed, or showing signs of overheating.
• Do not reapply power until repairs are completed.
• Refer any service operation not described in this manual to the PROLIGHTS Service team or an authorized service center.

Installation

• Ensure all visible parts of the product are in good condition before use or installation.
• Make sure the anchorage point is stable before positioning the device.
• Install the product only in well-ventilated places.
• For non-temporary installations, securely fasten the fixture to a load-bearing surface with suitable corrosion-resistant hardware.
• Do not install the fixture near heat sources.
• Operating this device differently from what is described in this manual may cause damage, void the warranty, and lead to dangers like short circuits, burns, or electric shock.

Max operating ambient temperature (Ta): Do not operate if ambient temperature exceeds 45 °C (113 °F).

Minimum operating ambient temperature (Ta): Do not operate if ambient temperature is below -10 °C (14 °F).

Protection From Burns and Fire

• The exterior of the fixture becomes hot during use. Avoid contact by persons and materials.
• Ensure free and unobstructed airflow around the fixture.
• Keep flammable materials well away from the fixture.
• Do not expose the front glass to sunlight or other strong light sources, as lenses can focus rays and create a fire hazard.
• Do not attempt to bypass thermostatic switches or fuses.

Indoor Use

• This product is designed for indoor and dry environments.
• Do not use in wet locations or expose to rain or moisture.
• Never use in places subject to vibrations or bumps.
• Ensure no inflammable liquids, water, or metal objects enter the fixture.
• Excessive dust, smoke fluid, and particle build-up degrades performance, causes overheating, and damages the fixture.
• Damages caused by inadequate cleaning or maintenance are not covered by the product warranty.

Maintenance

[Warning] Before any maintenance or cleaning, disconnect the fixture from AC mains power and allow it to cool for at least 10 minutes.

• Only technicians authorized by PROLIGHTS or authorized service partners may open the fixture.
• Users may perform external cleaning following provided instructions. Any other service operation must be referred to a qualified service technician.
• Excessive dust, smoke fluid, and particle build-up degrade performance, cause overheating, and damage the fixture. Damages from inadequate cleaning/maintenance are not covered by warranty.

Warning: Use of alcohol or other detergents may damage lenses.

Radio Receiver

This product contains a radio receiver and/or transmitter:

• Maximum output power: 17 dBm.
• Frequency band: 2.4 GHz.

Disposal

• This product complies with European Directive 2012/19/EU – Waste Electrical and Electronic Equipment (WEEE). Dispose/recycle this product at the end of its life according to local regulations.
• Do not throw the unit into garbage at the end of its lifetime.
• Dispose according to local ordinances to avoid polluting the environment.
• The packaging is recyclable.

Compliance:

• 2014/53/UE - Radio Equipment Directive (RED).
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).
• UL 1573 + CSA C22.2 No. 166 - Stage and Studio Luminaires and Connector Strips.
• FCC Compliance: This device complies with FCC 47 CFR Part 15 Subpart B. Operation is subject to two conditions: 1. No harmful interference. 2. Must accept any received interference.

1 - Packaging

Package Content

• 1 x AETHERBOXLITE
• User Manual

Optional Accessories

Check the updated accessories list, description, and information at: https://www.prolights.it/product/AETHERBOXLITE#accessories

2 - Technical Drawing

Dimensions:

• Length: 140 mm [5.5 in]
• Height: 102 mm [4.0 in]
• Width: 63 mm [2.5 in]

3 - Installation

Mounting

Check that the supporting structure can safely bear the weight of all installed fixtures, clamps, track adapters, cables, and auxiliary equipment, and complies with local regulations.

When suspending the fixture above ground level, secure it against failure of primary attachments by attaching a safety wire approved for the fixture's weight to an anchor point on the product's main frame. Do not use removable parts or weak anchors for secondary attachment.

Warning: When clamping the fixture to a truss or other structure at any angle, use half-coupler type clamps. Do not use any clamp that does not completely encircle the structure when fastened.

Diagram Description: Figure 02 shows the ÆtherBox LITE mounted on a truss. An arrow indicates the fixture is attached to the truss. Another arrow points to a 'Track adapter' attached to the fixture. A safety wire is shown connecting the fixture to the truss anchor point.

4 - Connection to the Mains Supply

WARNING: For protection from electric shock, the fixture must be earthed!

The product has an auto-switching power supply that adjusts to any 50-60Hz AC power source from 100-240 Volts (range: 90-264V).

If installing a power plug on the power cable, use a grounding-type (earthed) plug, following the manufacturer's instructions. Consult a qualified electrician if unsure.

Maximum power consumption is 5.8W.

NOTE: To avoid risk, the Powercon true and the screw terminal block must not be powered at the same time.

5 - Start Up

Connect and Disconnect Power

• Check that the product is installed and secured as per Safety Information, ensuring personal safety.
• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz).
• The product is now ready for operation and can be controlled via the onboard input signals.
• To disconnect power, unplug the Mains from the socket.

6 - Product Overview

The product features the following components:

1. USER INTERFACE: Buttons and status LEDs for accessing functions.
2. DMX IN (5-p XLR): Pinout: 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5 N/C.
3. DMX OUT (5-p XLR): Pinout: 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5 N/C.
4. POWER IN: For connection to the Mains (100-240V~/50-60Hz).
5. SAFETY HOLE: For attaching a safety cable.
6. BOTTOM COVER: Allows access to track adapter connections.
7. TRACK ADAPTER PLATE: Allows easy installation of the track adapter accessory.
8. RUBBER COVER: Covers the track adapter hole when not used.

Diagram Description: Figure 03 provides a 3D view of the ÆtherBox LITE with numbered callouts corresponding to the components listed above.

7 - Control Panel

Control Panel Overview

The product has an OLED display and 5 buttons for accessing control panel functions.

Buttons Layout

The product has a display and buttons for control panel functions:

• TX/RX Button: To select Transmitter or Receiver mode.
• LEDs ON/OFF Button: Push to power ON/OFF the LEDs.
• LINK Button: To reset connections or link fixtures.

Diagram Description: Figure 04 shows the layout of the control panel buttons (BT, DMX, RDM, TX, RX, LINK, 25%, 50%, 75%, 100%) and the three main operational buttons (TX/RX, LEDs ON/OFF, LINK). Figure 05 details the function of each main button.

8 - Use

CRMX Toolbox App

The AETHERBOXLITE can be controlled by the CRMX Toolbox app via Bluetooth:

• Google Play: Link
• App Store: Link

9 - RDM Functions

The product communicates using RDM (Remote Device Management) protocol over DMX512 Networks. RDM is a bi-directional protocol for DMX512 control systems, enabling device configuration and status monitoring. It allows data packets to be inserted into a DMX512 stream without affecting non-RDM equipment, enabling consoles or controllers to send commands and receive messages from specific fixtures.

The PIDs (Parameter IDs) in the following tables are supported by the product.

Product Information & DMX512 Setup

Sensors & Power/Lamp Settings

Manufacturer Specific PIDs

10 - Accessories Installation

Track Adapter (CODE NAKKT30600)

Diagram Description: Figure 06 illustrates the installation of the track adapter. Step 1 shows unscrewing a bottom screw. Step 2 shows removing the bottom cover. Step 3 shows assembling the track adapter mechanism. Step 4 shows the connection of screw terminal blocks for DMX (GND, DMX-, DMX+) and Mains (L, N).

NOTE: To avoid risk, the Powercon true and the screw terminal block must not be powered at the same time.

Clamp (CODE C6002, C6016)

Diagram Description: Figure 07 shows the installation of clamps. Steps 1 and 2 are similar to the track adapter installation, involving unscrewing and removing the bottom cover. Steps 3.1 (for C6002) and 3.2 (for C6016) show the assembly of the respective clamp types.

11 - Maintenance

Maintenance the Product

It is recommended that the product be checked at regular intervals.

• For cleaning, use a soft, clean cloth moistened with a mild detergent. Never use liquid, as it might penetrate the unit and cause damage.
• Users may upload firmware (product software) via the DMX signal input port using UPBOXPRO or UPBOX2, following PROLIGHTS instructions.
• It is recommended to check at least annually for new firmware availability and perform a visual check of the device and mechanical parts.

Warning: The use of alcohol or any other detergent could damage the lenses.

• All other service operations must be carried out by PROLIGHTS, its approved service agents, or trained and qualified personnel.
• PROLIGHTS policy is to use the best quality materials for optimum performance and component longevity. However, components are subject to wear and tear. The extent depends on operating conditions and environment. Components may need replacement after extended use if their characteristics are affected.
• Use only accessories approved by PROLIGHTS.

Visual Check of Product Housing

• Check product cover/housing parts for damage and breaking start at least every two months. If a crack is found on a plastic part, do not use the product until the damaged part is replaced.
• Cracks or other damages to cover/housing parts can be caused by transportation, manipulation, or aging.

Troubleshooting

Contact an authorized service center for technical problems not resolved by the procedures in this table.