Creality Space Pi Filament Dryer User Manual
Version: V6.0
Package List
- Creality Space Pi Filament Dryer x1
- Power Cable x1
- PTFE Tube x1
- User Manual x1
Product Introduction
Display Information:
- Real-time Temperature
- Drying Temperature
- Drying Material
- Drying Time (hours)
- Real-time Humidity
Control Buttons: Setting, Up, Down, Play
Kindly Reminder:
- When the product is placed in a humid environment, there may be some odor or smoke in first use, which is normal.
- The real-time temperature and humidity are only for reference for the environment inside the dryer, and cannot substitute for data given by a dedicated temperature and humidity sensor.
- After stopping drying, due to the fan ceasing to spin and residual heat remaining in the dryer, a slow increase in humidity levels shortly afterwards is normal. Upon opening the lid, an increase in humidity levels can be observed within approximately 30 minutes.
Product Parameters
| Product Series | Creality Space Pi Filament Dryer |
|---|---|
| Scope Of Application | 1kg Filament |
| Rated Voltage | UK/GB/EUR/AUS/BRA/CHL/ARG 220-240V~50/60Hz US/JPN 100-120V~50/60Hz |
| Working Temperature | 45~70°C |
| Working Time | 0~48H |
| Adjustment Mode | Touch Control |
Operation Guide
- Power On: Switch on the back power supply, then long press the "Play" button for 0.5s.
- Power Off: Long press the "Play" button for 0.5s, then switch off the back power supply.
- Switch Temperature Units: Long press the "Setting" button. A triangle icon will appear on the left side of the screen. Click "Setting" repeatedly until the triangle icon moves to the left of "PV". Then, use the "Up" or "Down" buttons to switch units.
Operation Guide (Continued)
- Modify Drying Temperature: Long press the "Setting" button. A triangle icon will appear on the left side of the screen. Click "Setting" repeatedly until the triangle icon moves to the left of "SV". Then, use the "Up" or "Down" buttons to modify the temperature.
- Change Drying Material: Long press the "Setting" button. A triangle icon will appear on the left side of the screen. Click "Setting" repeatedly until the triangle icon moves to the left of "Material". Then, use the "Up" or "Down" buttons to change the material setting.
- Modify Drying Time: Long press the "Setting" button. A triangle icon will appear on the left side of the screen. Click "Setting" repeatedly until the triangle icon moves to the left of "Time". Then, use the "Up" or "Down" buttons to modify the drying time.
Recommended Drying Temperatures For Different Filaments
| Display | Material | Temperature | Time |
|---|---|---|---|
| PLA | PLA | 50°C | 4-8h |
| PLA-CF | PLA-CF | 50°C | 4-8h |
| TPU | TPU | 55°C | 4-8h |
| PP | PP | 55°C | 4-8h |
| ABS | ABS | 65°C | 8-12h |
| ASA | ASA | 65°C | 8-12h |
| PETG | PETG | 60°C | 4-8h |
| PETG-CF | PETG-CF | 60°C | 4-8h |
| PC | PC | 65°C | 8-12h |
| PA | PA | 65°C | ≥12h |
| PA-CF | PA-CF | 65°C | ≥12h |
| PET | PET | 60°C | 4-8h |
⚠️ Warning: Please be aware that the outer shell may be hot to touch when the drying temperature is set above 60°C.
Instructions For Use Of PTFE Tube
-
Place the filament roll into the dryer. Feed the filament through the filament outlet on the top of the dryer as shown in the diagram.
Diagram Description: Filament Outlet
-
Thread the filament into the PTFE tube until a length of filament protrudes. Then, insert the front end of the PTFE tube into the filament outlet on the top of the dryer, ensuring a certain length is inserted.
Diagram Description: PTFE Tube
Attentions For Safe Use
- Please do not use this product when its power cord and socket are damaged or in contact with water.
- When not in use for a long time, please power off the product to avoid unexpected fire.
- Please never use this product under wet conditions.
- Please keep this product out of the reach of children.
- In case of any failure, please power off this product and then unplug it instead of using it continuously. Contact the after-sales service personnel for assistance, rather than replacing parts with non-original ones or dismantling the unit for repair.
- Please supply power according to the standard voltage required on the product nameplate; otherwise, there may be a possibility of abnormal operation.
After-sales Information
E-mail: CS@creality.com
Company Information
SHENZHEN CREALITY 3D TECHNOLOGY CO.,LTD.
Official Website: www.creality.com
Business Tel: +86 755-8523 4565
E-mail: cs@creality.com
Company Address: 18th Floor, JinXiuHongDu Building, Meilong Road, Xinniu Community, Minzhi Street, Longhua District, Shenzhen City, China.
Certifications: CE, FC, ROHS, PS E
