Dynalite | Philips lighting
Instruction Manual for PHILIPS models including: DMC2-UL, Multipurpose Modular Controller, DMC2-UL Multipurpose Modular Controller, Modular Controller, Controller
File Info : application/pdf, 6 Pages, 1.18MB
DocumentDocumentDDMMC2-CU2L, DMC2-CE Modular Controller Installation Instructions Instructions d'installation Installationsanweisungen Instrucciones de instalación Istruzioni per l'installazione Installatie-instructies Devices must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations. Les appareils doivent être installés par un électricien diplômé conformément à tous les codes et réglementations électriques et de construction nationaux et locaux. Die Geräte sind von einem qualifizierten Elektriker in Übereinstimmung mit allen geltenden Vorschriften zu installieren. Los dispositivos deben ser instalados por un electricista calificado y cumpliendo todas las normas y regulaciones, tanto nacionales como locales, sobre instalaciones eléctricas y obras. I dispositivi devono essere installati da un elettricista qualificato in conformità con le norme locali e nazionali vigenti in materia di costruzioni edilizie e installazione di impianti elettrici. De apparaten moeten worden aangebracht door een gekwalificeerde elektricien en in overeenstemming met alle nationale en plaatselijke elektriciteits- en bouwvoorschriften. / . 441 mm (17.36 in) 523 mm (20.59 in) 540 mm (21.26 in) X 4 Modules 285 mm (11.22 in) 352 mm (13.86 in) 380 mm (14.96 in) 106 mm (4.17 in) 1 2 3 200 mm (7.87 in) 200 mm (7.87 in) IEC Pollution Degree II 1 ¡ ¢ £¤ 1¡ ¥¦ 90% ¡ ¢ £0§¡ ¥¦ 200 mm (7.87 in) 4A 4B 5 IEC Overvoltage Category III 2 N1 N2 N3 L1 L2 L3 +24 V GND N1 L1 N2 L2 N3 L3 BUS Supply Module Output Module 1 N1 L1 N2 L2 N3 L3 BUS Output Module 2 BUS Communications Module 6 DCM-DyNet 7 1 Nm 8.8 Lb-in DCM-DyNet 3 8 DSM2 9 1 2 4 1 Nm 8.8 Lb-in DSM2-XX 1 Nm 8.8 Lb-in Installation example Exemple d'installation Installationsbeispiel Ejemplo de instalación Esempio di installazione Installatievoorbeeld MODULE 10 A Installation example Exemple d'installation Installationsbeispiel Ejemplo de instalación Esempio di installazione Installatievoorbeeld MODULE 10 B Installation example Exemple d'installation Installationsbeispiel Ejemplo de instalación Esempio di installazione Installatievoorbeeld MODULE MODULE 2 MODULE 1 SUPPLY N1 N2 N N3 L1 L1 L2 L2 L3 L3 N1 L1 N2 L2 N3 L3 Refer to enclosure label for earth bar wire gauge and torque ratings 11 MODULE 2 MODULE 1 SUPPLY N1 N2 N N3 L1 L1 L2 L2 L3 L3 N1 L1 N2 L2 N3 L3 N1 L1 N2 L2 N3 L3 Refer to enclosure label for earth bar wire gauge and torque ratings 12 DSM2 1 2 DCM-DyNet DMC2 DMC4 13 RS-485 DyNet Device must be de-energized before terminating cables. Do not energize without the front lid top cover in place. 5 14 4 1 3 2 15 Channel 1: Channel 2: Channel 3: Channel 1: Channel 2: Channel 3: Channel 1: Channel 2: Channel 3: Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any modifications not approved by the manufacturer of this device could void the user's authority to operate this device. Installation of a home and building automation and control system shall comply with IEC 60364 (all parts). The temperature limits and current-carrying capacities for the communication wires specified in IEC 60364-5-52 shall not be exceeded. This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B). Cet appareil numerique de la classe B est conforme a la norme NMB003 du Canada: CAN ICES-3(B)/NMB-3(B). © 2022 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners. www.lighting.philips.com/dynalite AZZ 431 0622 R15