CYCPLUS D17 Pro Intelligent Air Pump

Pump Instructions

This product is an intelligent air pump with adjustable pressure settings, designed for inflating and deflating SUP boards, kayaks, tents, mattresses, and more.

The CYCPLUS D17 Pro is a two-stage pump capable of inflating items up to 20 PSI. It features a high-precision manometer that measures pressure and automatically stops inflation when the set pressure is reached.

After use, ensure proper storage and enjoy your outdoor activities.

Before Use

Environmental Requirements

• Do not expose the pump to rain or immerse it in water. Always store it in a dry place.
• Keep the pump and inflatable items away from heat sources, extreme cold, humidity, dust, and direct sunlight.
• Do not use the pump in flammable or explosive environments.
• Use the pump at an ambient temperature below 40°C.

User Limitations

• This pump is not a toy; keep it out of reach of children.
• The pump is not intended for use by individuals with physical, sensory, or mental disabilities unless supervised by a responsible adult.

Technical Control of the Pump

• The pump must be used only as instructed.
• Do not set a pressure higher than the maximum allowable pressure for the inflatable item.
• The pressure range of this pump is applicable only to the original inflatable hose and nozzle.
• This pump is suitable for SUP boards or other inflatable items with an air pressure of up to 20 PSI.
• Inspect the appearance of the pump and all accessories to ensure they are functional and undamaged.
• If any parts of this air pump are damaged, do not use it and contact after-sales service.

Pump Disposal

• Do not dispose of the pump in fire to avoid explosion, battery leakage, or other hazards.
• Do not dispose of the pump as ordinary household waste. Waste must be collected separately for specialized recycling.

Safety Precautions

• Do not use the pump while charging.
• Do not turn off the pump during operation, setup, or maintenance.
• Ensure that the inflation and deflation ports are never blocked.
• Do not point the pump's inflation or deflation ports at anyone.
• Do not use the pump if water is suspected to have entered it. Always keep it dry.
• Do not leave the pump unattended for extended periods during use.
• To avoid accidental injury, do not disconnect the air hose during inflation.
• If you notice any abnormal sounds or high temperatures during use, stop the pump immediately.
• This pump should cool down completely for 30 minutes after 20 minutes of continuous operation to prevent internal damage caused by motor overheating.

Description

Screen Display:

• Real-time pressure value
• Set pressure value
• Unit of pressure measurement (PSI/BAR)
• Battery charge level
• Inflation port
• Deflation port

Buttons:

• Type-C port for charging
• Mode button
• Power button
• '-' button
• '+' button

Packing List

Ensure all accessories are present and in good condition. If you find any issues, contact after-sales service.

• Air pump
• Air hose
• Air nozzles
• Red sealing ring (spare)
• Orange sealing ring (spare)
• Blue sealing ring (spare)
• 2 white sealing rings (spare)
• Type-C cable for charging
• User manual

Button Description

Operating Instructions

Inflation

1. Hose Connection: Connect the hose to the inflation port and secure it (Step 1). Attach the air nozzle to the hose and secure it (Step 2). Insert the nozzle into the inflatable item's valve and secure it (Step 3).
2. Press and hold the [Power button] to turn on the pump; the screen will light up.
3. Long press the [Mode button] to select the pressure unit.
4. Press the ['+' and '-'] buttons to set the desired pressure (0.5-20 PSI / 0.04-1.4 BAR).
5. Press the [Power button] to start inflation.
6. You can press the [Power button] at any time to stop inflation.
7. The air pump will automatically stop when the set pressure is reached.
8. A long press of the [Power button] for 2 seconds after inflation will turn off the power, and the screen will go dark.

Deflation

1. Before deflating, open the SUP board valve to release some of the high-pressure air.
2. Hose Connection: Connect the hose to the deflation port and secure it (Step 1). Attach the air nozzle to the hose connector and secure it (Step 2). Insert the nozzle into the inflatable item's valve and secure it (Step 3).
3. Press and hold the [Power button] to turn on the pump; the screen will light up.
4. Press the [Power button] to start deflation.
5. Press the [Power button] to stop deflation in time, to avoid overheating the air pump.
6. A long press of the [Power button] for 2 seconds after deflation will turn off the power; the screen will go dark.

Operating Modes

1. Press and hold the [Mode button] to switch between FAN, CPR, and AUT modes.
2. After switching, the current mode will appear on the screen, blink twice, and return to displaying the real-time air pressure.
3. After restarting, the pump will return to AUT mode.

Operating Modes:

• FAN: Inflation using a fan (high airflow, max pressure 1 PSI).
• CPR: Inflation using a compressor (lower airflow, max pressure 20 PSI).
• AUT: Inflation using a fan if the current pressure is below 0.8 PSI, and using a compressor if the pressure is above 0.8 PSI.

Power Options

Charging

• This pump operates on a built-in battery and is charged via a USB Type-C interface.
• Use a charger that supports an output voltage of at least 5V, 2A. Failure to meet this condition may result in excessively long charging times or inability to charge.
• During charging, the battery indicator on the screen will flash, gradually increasing, and will light up continuously when fully charged.

Power Bank Function (Portable Charger)

• The air pump can function as a portable charger for other electronic devices via the USB Type-C interface. In Power Bank mode, the screen will display the battery charge level, and the indicators will be constantly lit, not flashing.
• If charging does not start immediately after connecting the device, press any button on the pump to start charging immediately.
• The pump cannot be charged or used as a portable charger while inflating or deflating.

Battery Maintenance

• Be sure to charge it at least once every 6 months and use it once a year to ensure reliable battery function.

Manometer Calibration

Recalibration of the manometer is required in the following cases:

1. If the screen displays a value other than 0 when the air pump is not connected to an inflatable item.
2. If the pump does not switch between fan and compressor when operating in AUT mode.

Procedure:

To calibrate the manometer, ensure the air pump is not connected to an inflatable item.

Press and hold the '+' and '-' buttons simultaneously until 'CAL 5' appears on the screen, after which the manometer will reset to 0.

Protection Mechanism

1. The air pump will automatically shut off after 1 minute if it is not operating or inflating.
2. The air pump will automatically stop if it continuously inflates for 20 minutes to prevent continuous operation due to abnormal working conditions.
3. The air pump will automatically stop after 10 minutes if the air pressure remains below 1 PSI to avoid inefficient operation.

Technical Specifications

• Dimensions: 215 × 172 × 85 mm
• Weight: 1.65 kg
• Battery: 5200 mAh / 18.5 V (96.2 Wh)
• Max. Inflation Pressure: 20 PSI
• Working Voltage and Current: 18.5V=13A (max.)
• Rated Power: <240W
• Type-C Input: 5V=3A, 9V=3A, 12V=2.5A, 15V=2A, 20V=1.5A
• Type-C Output: 5V=3A, 9V=3A, 12V=2.5A, 15V=2A, 20V=1.5A
• Storage Temperature: -10°C to 60°C
• Operating Temperature: 0°C to 40°C

Troubleshooting

Do not use this pump or attempt the following methods if water is suspected to have entered. Let the pump dry for 3 days before attempting to turn it on!

The table below lists possible problems that may occur during use. For troubleshooting, refer to the causes and solutions in the table. If the problem cannot be resolved, contact after-sales service.

Error Codes:

Manufacturer Information

Company: Chengdu Chendian Intelligent Technology Co., Ltd.

Address: No.88 Tianchen Road, Chengdu, Sichuan Province, China

Warranty: Free repair or replacement for 1 year for non-human-induced damage.

Contact: support@medgadgets.ru

Nozzle Description

For SUP boards:

• Valve Type: Halkey-Roberts New Shot, Summit 2, H3, Runho
• Adapter 1

For SUP boards:

• Valve Type: Leafeld C7, Leafeld D7
• Adapter 7

For inflatable items:

• Surfing Kite
• Duotone valve
• Blue sealing ring

For inflatable rings:

• Items: Inflatable ring, inflatable beach ball, etc.
• Adapter 1+2+3

For Boston valve:

• Items: Inflatable boat, inflatable mattress, inflatable tent, etc.
• Adapter 1+2+4

For Decathlon self-inflating mattress:

• Adapter 1+2+5

For 34mm two-way valve self-inflating mattress:

• Adapter 1+2+6

For regular vacuum storage bag

This instruction is for reference purposes only. Please select the appropriate nozzle based on the actual conditions.

For continuous improvement of functionality and user experience, CYCPLUS may make changes to the design, functions, or accessories. The actual product you receive may differ from the one described in this manual. For final information, please refer to the actual product.

Contacts

CALL CENTER

Mon-Fri: 9:00-18:00 (Moscow time)
Sat-Sun: Days off

+7 (929) 625-15-15
info@medgadgets.ru

WEBSITE: CYCPLUS.COM

Warranty and Returns

CYCPLUS PRODUCTS COME WITH A 1-YEAR MANUFACTURER'S WARRANTY

The warranty covers manufacturing defects. The warranty does not cover cases of misuse, improper operation, loss, or theft of the device.

MGADGET is the official distributor of CYCPLUS products in Russia.

CLIENT SERVICE MGADGET

Email: support@medgadgets.ru
(Our technical support will respond within 3 business days)

Working Hours: Mon-Fri, 9:00 to 18:00 Moscow time
Office Address: 140002, Lyubertsy, Oktyabrsky prospect, bldg. 20, корпус 2