Instructions for RUIDENG models including: RUIDENG, AT34, USB Tester with Full Colour Display
We also advise that you keep these instructions in a safe place for future reference as may be needed. Technical Parameters: Model: AT34. Display screen：0.96 ...
Quick charge recognition mode：QC2.0、QC3.0、APPLE 2.4A/2.1A/ 1A/0.5A、Android DCP、SAMSUNG Function Interface: Measurement Main Interface Quick Charge Recognition Interface Button Instruction: The button is located on back of the tester. There are 2 kinds operation ways, long press and short press.
File Info : application/pdf, 3 Pages, 517.72KB
DocumentDocumentHangzhou Ruideng Technologies Co., Ltd Instructions for USB Tester with Full Colour Display -Model: AT34 Dear Customer, Thank you for purchasing this Full Colour USB Tester from Hangzhou Ruideng Technologies Co., Ltd. Prior to using this product we recommended that you briefly familiarize yourself with these instructions. In order to ensure the correct operation and use of the device. We also advise that you keep these instructions in a safe place for future reference as may be needed. Technical Parameters: Model: AT34 Display screen0.96 Inch color IPS display Voltage measurement range:3.70-30.00V Voltage measurement resolution:0.01V Current measurement range: 0-4.000A Current measurement resolution: 0.001A Capacity accumulation range: 0-99999mAh Voltage measurement accuracy:±(0.8+4digits at 25) Energy accumulation range:0-99999mWh 999.99Wh Current measurement accuracy: ±(1+4 digits, at 25) Load impedance range: 1-9999.9 Power measurement range:0-120W Temperature range:0~80/32~176 Temperature measurement error:± 3/ ± 6 Working temperature range: 0~45 Refresh rate: 2Hz Dimensions64mmx22mmx12mm Product weight:14g (package 28g) Quick charge recognition modeQC2.0QC3.0APPLE 2.4A/2.1A/ 1A/0.5AAndroid DCPSAMSUNG Function Interface: Measurement Main Interface Quick Charge Recognition Interface Button Instruction: The button is located on back of the tester. There are 2 kinds operation ways, long press and short press. Short press is to realize switch between Measurement Main Interface and Quick Charge Recognition Interface. Long press is to realize switch of system setting. 1 Hangzhou Ruideng Technologies Co., Ltd Introduction of Icon Function 1 Press and hold the button to choose this icon to open or close the screen 2 Press and hold the button to choose this icon to switch the temperature unit. 3 Press and hold the button to choose this icon to switch data group 4 Press and hold the button to choose this icon to clear data group. 5 Press and hold the button to choose this icon rotate the screen Operation Instruction: After power on, welcome interface will be displayed firstly, then main measurement interface will be shown. Interface 1: Main Measurment Interface. 6Voltage Measurement 7Current Measurement 8Accumulated Capacity 9Accumulated Energy 10Temperature Measurement 11Number of the Data Group in use 12Load Equivalent Impedance 13Power Measurement Press the button on the back to switch to Quick Charge Recognition Interface Interface 2: Quick Charge Recognition Interface: 14D +: (DP) data positive signal level. 15D-: (DM), data negative signal level. 16Mode display The product will automatically identify a device with a supported fast charging mode. At this time the device supports the QC2.0QC3.0APPLE 2 Hangzhou Ruideng Technologies Co., Ltd 2.4A/2.1A/ 1A/0.5AAndroid DCPSAMSUNG.(Note: This quick charge agreement recognition model is for reference only, because cell phone updated quickly, it can't be absolutely accurate identification Parameter Setting: At any interface of 2 interfaces, Press and hold the button to realize data set. Long press the button more than 0.5s, the corresponding icon will be selected and displayed (the background of icon turns black to blue), then step through the options of screen off, temperature display units, data group switch, data group clear zero and screen rotation. Stop on the function you wish to set then loosen the button Press and hold the button, the corresponding icon will be selected and displayed, then loosen the button, screen will be off, then press the button or power on again, the display will light again . Press and hold the button, the corresponding icon will be selected and displayed, then loosen the button, the temperature unit will be switched. Degree centigrade is the default temperature unit Press and hold the button, the corresponding icon will be selected and displayed, then loosen the button, data group will be switched. This tester can provide 2 groups to store and check, 0 and 1 data group. When the data set is 0 group, the current capacity will be stored after power off. When power on next time, the stored mAh and mWh is blinking displayed. When the new mAh is up to 1 mAh, the stored mAh and mWh will be covered, and the values will start over. When data set is group 1, the current capacity will be stored after power off. And the stored capacity will be accumulated after power on. Press and hold the button, the corresponding icon will be selected and displayed, then loosen the button, the data of the current data group will be zero. Press and hold the button, the corresponding icon will be selected and displayed, then loosen the button, the screen will be rotated 180 degree, and stored automatically, which is convenient for later using 3Microsoft Word 2016